ONE15ISALLINEED

i personally have experienced problems with rca outputs on pioneers going bad and other people

Sub is in a slot port enclosure, 3.5 cu ft, tuned @ 32hz. I was thinking a sundown saz2000. the audioque 2200d is a little more budget friendly. especially at 389 brand new shipped. on top of other minor upgrades with the electrical system i will have to do. Suggestions appreciated.

i came to the conclusion that the voice coils burnt out. im now facing another problem. i still have my audioque 1200d installed. i now have a new atomic ap15 installed. i mounted in my box and went to wire it up. i then turned the car on to find that my amplifier is not turning on. why, i do not know. a week ago when i was doing testing it came right on and i have not touched it since. i checked my power wire fuse, good. i checked the amp fuses, good. possible wire shortage? remote wire problem? i have not had a problem with it not turning on at all. its very frustrating never had so many problems with a system before, thanks for help. add on: if i had a band ground for my amp, would my amp power light even come on?

well i took the sub out to check if the wires were connected inside maybe they were coming loose...they were intact...i also noticed when the amp is on theres a small airy noise coming from the speaker like a channel station that isnt coming in

watch the show as it developes, lol. I still have yet to check it all out. this setup is actually in my girlfriends car. Hard for me to find the time to look at it. Im just wondering if it reall is the sub that was burning. He clearly put his nose to the port on the box and then smelled the diamond amp and said the amp was burning up. he told me get a new one so i did and the smell is still there after some hard playing. once i dis mount the sub and check it out ill determine it.

no the sub is wired correctly i know that. i meant the wires running from the box to the amp could possibly been wired from + to - , vice cersa

another question. if for some accidental reason i wired from the amp to the box terminals the opposite way (positive to negative), would that fry the sub instantly or through time? i only experienced this problem through out a couple days. the thing is i dont have spring terminals they are bolts. its a dual 2 ohm wired to 1 ohm. im almost sure i have the wires right just have not took the time to take out and check it all

i do not know what my voltage is at. The audioque 1200d has a protection mode, im saying that it is not going into protection mode though

Just recently i have experienced some problems with my system. 15" diamond audio hex pro & audioque 1200 (witch use to be a diamond audio 1200). At first i was experiencing a slight smell after a minute or so at loud volume. A friend of mine told me the capacitors in my diamond audio amp were frying. I then purchased a audioque 1200 and swapped it out with the diamond amp. At the first install the ground was bad so i moved it and scraped the paint. The slight smell came back even after switching the amps. I then started to experience the subwooofer fading in and out at times. One time it went completely silent and after turning the car on and off the sub came back on. It then again began to fade in and out to where i get no sound from the sub at all. Now what im wondering are what the possibilities are problem wise and what steps to take. Is the sub blown, is there a bad ground, rcas on head unit? The audioque's power indication light is on. Thanks for any replies

im pretty sure theres hundreds of available pre-fab boxes built for your truck online. or even put a order in at your local audio shop. what year is it? edit - 07 based on your screen name

ya THANKS lucky for a more positive answer appreciate it. gotta learn someday riiight?

good answer shizzzon, exactly what i was looking for, thanks

im asking in general. are these ports specific for spl. i mean do people really drive around with that thing in there truck. looking like a christmas present out of how the grinch stole christmas

are these spl boxes? cuz that thing is damn ugly

while were talking about ohm loads here, dont you want to run as many ohms as you can while still feeding at least the rms power into a sub. the more ohms the "harder" or "deeper" the sub performs. fill me in plz