Jump to content

nicholasrhall

Members
  • Content Count

    73
  • Joined

  • Last visited

Everything posted by nicholasrhall

  1. nicholasrhall

    2 Skar Sk-2500

    Saw your build log, your in Huntsville, Alabama right?
  2. nicholasrhall

    2 Skar Sk-2500

    still for sale?
  3. nicholasrhall

    SEALED REAR CHAMBER BP ENCLOSURE (4TH ORDER)

    Great job on making this as simple as possible. So much easier to understand than anything else ive read. Ill have to use this in future builds. It'll make things so much easier. Sticky this? Maybe post this up in SQL/SPL fabrication section as "4th order bandpass for dummies" or something like that.
  4. nicholasrhall

    Port location/type for Zcon 12

    Under 3 cuft wont hurt anything. From what I understand, the zcons seem to like the smaller enclosures. its recommended a 2.5- 3.25 cu ft ported. So you should be fine. I had my 2 xcon 12's in 3.9 cuft ported at 31 hz and they loved it. Metered a 143.7 sealed at the glass with no deadening on around 1500 watts. If the zcons are anything like the xcons parameter wise, i think it'll work great for you. But dont just take my word for it. im just going off what ive seen and heard from friends.
  5. nicholasrhall

    My First "Real" Jeep Build

    wierd. thats the only reason i could think for a key to be there. maybe the original owner had some idea for something.
  6. nicholasrhall

    My First "Real" Jeep Build

    Thats what I initially though because the keys for the Jeep have Chips and you need to bypass for remote start but nothing on the wire was exposed, and id imagine the wire would have to touch the metal? Regardless im ordering one of those alarms with an LCD on the remote that goes off when a doors open and shows which door, so Ill just save that project until I purchase that. I actually had to do this last week at a shop i work at. I used the secondary key to make sure the chip was a ignition issue. But in short the reason your prolly has that key behind the dash is because the chip in the original key failed. And alot of people will do that instead of changing the ignition cylinder. It can be done on chryslers chevys and any car with a chipped key. What happens is that your sort of bypassing your anti theft system, the wires should be going to the key cylinder and then when wrapped around the other key(and then some wires have to be cut and jumped), it will fool your car into thinking it has a the correct key in it. This doesnt however make your car easier to steal. from what i understand you should still have to have the chip in the original key to make the complete circuit to start the car.
  7. nicholasrhall

    I need some design help for my box

    Let me know asap. Im thinking about starting on the build soon.
  8. Im designing a box for my new improved build and i jus want to verify that im doing it all correctly. The box will be for two 15 inch SSA EVIL series subs. But for right now i have two dc lvl 4 15's that will go into the box temporarily. So it will be designed mainly around the EVIL's. The car its going into is a 2007 Scion Tc. I measured out max dimensions and came up with a box that i think turned out very well. i wanted it tuned low, mid 30's and low 31's maybe. Heres what i came up with::: Pic from sketchup (Copied and pasted from MS word) Box Measurements Maximum limits for the SCION TC Width = 37 inch max (pushing) Depth = 38 inch max (also pushing) Height = 15 inch max after double baffled 14.25 inch height before baffle and 12.75 internal height for mounting depth Subwoofer Displacement- .22 per sub (EVIL SSA 15) = .44 total .21 per sub (DC LVL 4 15) = .42 total Bracing Displacement = Using 2x4’s(1.5”x3.5”) = ( .125x.292x??? ) Using max internal Height – Up and down bracing – 1.5”x3.5”x12.75”.039 CuFt x3 (Three braces) Total displacement in CuFt = 0.117CuFt Using max Width internal – Side to side (Port wall to right wall) 1.5”x3.5”x35.5” .108CuFtx2(two braces) Total displacement in CuFt = 0.216CuFt Using max Depth internal – front to back bracing – 1.5”x3.5”x36.5” .111CuFtx2 (also two braces) Total displacement in CuFt = 0.222CuFt Box bracing displacement for max measurement specs – Total = 0.555 CuFt Total Box Displacement for max dimensions including woofers and braces Using SSA EVIL 15’s = .995 CuFt displacement Using DC LVL 4 15’s = .975 CuFt displacement 8.1CUFT without displacement 7.105 cuft displacement with EVIL 15’s and bracing 7.125 cuft with dc 15’s and bracing Port dimensions 12.75 H x 7.5 W =95.625sqin With EVIL 15’s – SqIn of port per cuft = 13.5 With DC LVL 4 15’2 – SqIn of port per cuft = 13.4 Tuning with EVIL 15’s = 30.47 Hz tune Tuning with DC 15’2 = 30.425 Hz tune Does all of this look correct? Am i missing anything that is throwing me off or is this perfect?
  9. nicholasrhall

    I need some design help for my box

    yah I was gonna stagger/offset them. that or jorizontal mount. I jus wanted to make sure my math was right and the tuning was correct.
  10. nicholasrhall

    I need some design help for my box

    Well if all my math is correct, and the box that i built is correct, then shouldnt it all fit?
  11. nicholasrhall

    ShiZZZoN's Build #2 The Epicness of 2011-2024

    The brake light thing is probaly the one inside the cluster. My tc does the same thing. 2007 Tc. It started doing it when my brakes were pretty worn. It was due to the fluid level being just a little low due to the pads being a little worn. Its either the fluid due to pad wear or the e brake needs adjustment, but id lean towards the fluid. It should stop when you get the brakes serviced. When the fluid is a little low and you take off at with good pace, the fluid shifts and goes farther from the sensor. Its nothing bad. Just watch the pad wear and fluid levels. Just dont top off the fluids unless theres a fluid leak. I work at a shop and theres reasons most places dont top off brake fluids when you have significant pad wear. 1. theres nothing wrong with it being a little low due to pad wear, topping it off is pointless. 2. Fluid levels double as a pad wear indicators. 3. It makes a hell of a mess when you service the brakes.(when you push the pistons back into caliper, fluid overflows from resevoir and goes everywhere) 4. its a sealed system the only reason youd ever need to add fluid is if there is a leak somewhere.
  12. nicholasrhall

    WTB: SSA XCON 12D1, Alpine PDX 1.600

    i have one, what would you offer shipped?
  13. nicholasrhall

    2 12 inch SSA XCON box design ideas and I need help

    http://www.soundsolu...&attach_id=3097 I'd use this one before all the others. 4.4ft^3 @ ~33hz add a little bit of dowel bracing and it would be perfect. the other one is about 4.5 cubes too, but i accounted for sub displacement (.34ft^3 for two 12's) and dowel bracing displacement. so it'll be roughly 4-4.1 ft^3 in the end.
  14. ok so im designing a box for two 12 inch xcons, ported going into my 2007 scion tc(Hatchback). Right now i have a decent box but its time for a rebuild. My box right now is 40.5 inches wide, 20 inches deep, and 17 inches high behind the rear seats. Its tuned at about 29-31 htz(not too sure). It does a 143.7 on the meter sealed up on the glass. No deadening, no beauty panels. But my concern is that my port is an Lport on the drivers side, it only goes halfway across the box so one woofer is above the port and the other is not. Im worried that the sub above the port is loading off of it and the other is not. If it is i want to fix this, so a rebuild is underway. It has been almost a year with this box so i might as well. What i want to know is, what is the best placement of the port and woofer? Sub up/port back? Sub back/ Port back? Sub forward/port forward? sub up/ port sidefiring? Sub forward/ port sidefiring? Sub back/Port sidefiring? Im using winisd to help design it and also using google sketch up. I am going to be putting two 12 inch xcons D1 woofers on about 2400 rms(soon to be ALOT more tho) What amount of port area do i need for the enclosure? will be updating this thread with more info as i go, along with shit loads of questions. Also going to design each enclosure and post a pic from sketchup of it along with specs, so i can get some sense of confirmation. kinda doing this to see if a better design will put up a better number. still with no deadening and no beauty paneling. Then will add beauty panels and test again, then remove it all and deaden the shit out of the car and see what it does. IDK why i wanna do that, jus kinda curious i guess.
  15. nicholasrhall

    2 12 inch SSA XCON box design ideas and I need help

    Thanks to everyone who has put input on this, i really and truely appreciated the help. i will be posting a build log for this box later, look out for it if you want. will also include installing door speakers extra batts and amps and stuff
  16. nicholasrhall

    2 12 inch SSA XCON box design ideas and I need help

    nvrmnd its like 4.053ft^3 tuned at about 33.285htz. unless my math is jus really screwed up
  17. nicholasrhall

    2 12 inch SSA XCON box design ideas and I need help

    aight so it would be like this correct? but what would the volume end up as?
  18. nicholasrhall

    2 12 inch SSA XCON box design ideas and I need help

    would there be a spl loss or gain going either way?
  19. nicholasrhall

    2 12 inch SSA XCON box design ideas and I need help

    I personally would, but in the end it is your call. how much would it bring the box volume down to? what would it tune the box to to just bring the port to 34.75 inches? that would give me five inches all the way through
  20. nicholasrhall

    2 12 inch SSA XCON box design ideas and I need help

    He's doing a side port. The external width of the box is 40.5" - 0.75" - 0.75" = 39" The port length would be 36". Why wouldn't 36" fit in 39"? So if his port was 38" long he would still not have to bend it? but he would have 3.75" left open to the port entrance. You don't think that's enough? I always try to bend at the port width if possible. 3.75 should be enough but I would still bend at 34.75. I know with aero ports people say half of the port width, but that is a minimum and I always try to use more if possible. Would your way sound any different than my way, probably not. It is just how I have always done things and I was curious as to see when you would draw the line and bend it. so would you say go through the trouble of bending it or jus leave it with 3.75 inches of clearance?
  21. nicholasrhall

    2 12 inch SSA XCON box design ideas and I need help

    aight, either way is cool as long as ill have enough volume in the end
  22. nicholasrhall

    2 12 inch SSA XCON box design ideas and I need help

    so it should effectively look like this?
  23. nicholasrhall

    2 12 inch SSA XCON box design ideas and I need help

    ohhh so the port starts at the very beggining of the port opening in the box? ive been under the impression that if the port goes close to the back wall then the distance should be the same as the width of the port and should turn
  24. nicholasrhall

    2 12 inch SSA XCON box design ideas and I need help

    ohh, but if my port is 5 inches wide, wouldnt it need to be five inches all around? cuz if i did a 36 inch length there would only be 3inches of space at the end
×