Jump to content
Sign in to follow this  
Tmax98

Distro block help

Recommended Posts

hey guys

i need some help here i have been runnin all over the web trying to find a proper distro block but it seems very hard to find the one im lookin for

so here is what im lookin for a 2 way distro

with 1/0 input

and a 1/0 output

and a 4awg output

and can be fused to 300 amps

thanks

Share this post


Link to post
Share on other sites

The one you linked will work, but it uses the same type connections as the KnuKonceptz blocks that are a total PITA to work with.

Share this post


Link to post
Share on other sites

it doesnt have a 4Ga output though... search around more and you should be able to find a 1 in 2out.... Some of them even have insert so you can choose 1Ga, or 4Ga

Share this post


Link to post
Share on other sites

just get one with 2 1/0 gauge outputs, the 4 will fit in just fine

Share this post


Link to post
Share on other sites
just get one with 2 1/0 gauge outputs, the 4 will fit in just fine

that was the plan :)

Share this post


Link to post
Share on other sites
The one you linked will work, but it uses the same type connections as the KnuKonceptz blocks that are a total PITA to work with.

what was such a PITA?

i have 2 knu distros right now didnt have to much trouble with them

besides not haveing some wire cutters and cutting the 4awg with my pocket knife lol

death to the scearaed :suicide-santa:

Share this post


Link to post
Share on other sites
just get one with 2 1/0 gauge outputs, the 4 will fit in just fine

that was the plan :)

checked darvex.com?

Share this post


Link to post
Share on other sites

just did the one i found was the only one sutible for my application

the knu ones would work but the fuses are too small

Share this post


Link to post
Share on other sites
The one you linked will work, but it uses the same type connections as the KnuKonceptz blocks that are a total PITA to work with.

what was such a PITA?

i have 2 knu distros right now didnt have to much trouble with them

Getting the compression fittings threaded straight was a pain, but getting them tightened down to where they wouldn't come loose was almost impossible.

Share this post


Link to post
Share on other sites
The one you linked will work, but it uses the same type connections as the KnuKonceptz blocks that are a total PITA to work with.

what was such a PITA?

i have 2 knu distros right now didnt have to much trouble with them

Getting the compression fittings threaded straight was a pain, but getting them tightened down to where they wouldn't come loose was almost impossible.

Oh my god!

You aren't lyin!

I have their Konfused battery terminals... I already crossthreaded one battery terminal insert because of their impossibility.

The idea is a good one, but unless you have 2 hrs of patience, it's ridiculous to the HIGHEST level.

It took me just over 2hrs to install the positive terminal on my starting battery. That is just stupid.

They better not come loose either.

I liked everyone else's terminal's where they're held in by screws but couldnt find any that could accept minimum of 3 2/0 wires.

Share this post


Link to post
Share on other sites

ya i think i may have cross threaded my distros on one

and i tighted one fittin to much and bent it and it looked like an oval lol

but have had no problems as of yet lol

and i will be gettin rid of the 3way block once this one comes in if somebody well send me a few bucks for it :peepwall:

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

×