Jump to content
liljestrand

08 scion xb^2 B2 products galore.

Recommended Posts

Comparing outside physical characteristics of a motor is a terrible way to compare woofers. They are two completely different woofers who share the same size ferite slugs.

Share this post


Link to post
Share on other sites

looking good, I think th SP4 motor should have been bigger considering the coil size

agreed... its weird how the SP4 and the Zcon look like they have the same motor...

Ironic?

All SSA motors look nearly identical to Fi models.

perhaps the same company lol

the top plate and bottom plate are diff of course to fit the coil.

yes the wofferes are very different, motors not so much lol.

I think it would be interesting to compare a SP4 to a ti styled sub with a 4hp :)

Share this post


Link to post
Share on other sites

et6yc5.jpg

this is the rough sketchup...and i mean rough....of the new box....should be just over 6 cubes after displacement

Share this post


Link to post
Share on other sites

looking good sir!

Share this post


Link to post
Share on other sites

Get it going man! :-)

Share this post


Link to post
Share on other sites

No more Zcons ? You're running Fi sp4's now. Why did you change ?! :)

Nice installs

Share this post


Link to post
Share on other sites

No more Zcons ? You're running Fi sp4's now. Why did you change ?! smile.png

Nice installs

So he could run a sealed box instead of a ported box

Share this post


Link to post
Share on other sites

No more Zcons ? You're running Fi sp4's now. Why did you change ?! smile.png

Nice installs

So he could run a sealed box instead of a ported box

I read the same a while back but not it looks like he's building a ported box. Am I wrong?

Share this post


Link to post
Share on other sites

imagejpeg_2_9.jpg

:TMNT:

Share this post


Link to post
Share on other sites

I did state the change was to go sealed and get my backseat back.

I met up with some team nwspl guys and they felt we could build a ported box in the cargo area.

So the box will be ported but it will be small for the zcons optimally.

It will be roughly 6 cubes after displacements.

We will do some straight up test because not only I but some team members are interested in the results.

And Sen posted a pic of one of my problems I found today. The crescendo pa mids are a Tad bigger than the ia comps I had

Share this post


Link to post
Share on other sites

I am tuned in!

Share this post


Link to post
Share on other sites

I heard the Crescendo mids are not as impressive as a lot of people hoped they would be, they are getting a couple things changed on them with the new batch coming out. Navid is always improving things

Share this post


Link to post
Share on other sites

Most of the problems are either weak terminal mounts. Or a scratchy sound. The scratchy sound means something got in the coil gap. If you unscrew the middle bullet thing and spray air in there it should clear it out.

But hey its a beefy little speaker for only 25 bucks. Hopefully get to hear it this week. Will be matching these with their ft1 supertweets

On the crescendo 1100.4

Share this post


Link to post
Share on other sites

Looking good, I'm anxiously your review of the sp4s. popcorn.gif

Share this post


Link to post
Share on other sites

Cant wait to see the box phil

And even better the results :)

Share this post


Link to post
Share on other sites

Well box will be built tomorrow. Can't wait!

Heres some pics to tide you over.

IMG_20120328_113519.jpg

how everything looks below the cargo floor. It's a bit messy but I had to do what i could to get this ready for the box build tomorrow.

And yes i know the inputs are above the other amp. I have a rubber mat underneath them atm till something better can be thought of.

IMG_20120328_122019.jpg

Cargo floor back in waiting on the box build.

IMG_20120328_144604.jpg

Team NWSPL shirts!

Share this post


Link to post
Share on other sites

Nice!!! I don't gots a team.. But I play for all... lol

Share this post


Link to post
Share on other sites

IMG_20120329_113946.jpg

Project DB 1/0 to 4g adapters on the 1100.4

IMG_20120329_121150.jpg

Starting the box.

IMG_20120329_132326.jpg

Back wall

IMG_20120329_170153.jpg

IMG_20120329_171947.jpg

IMG_20120329_193305.jpg

IMG_20120329_202236.jpg

IMG_20120329_204450.jpg

IMG_20120329_214119.jpg

And thats where we are at. Was a good day of good company and much bs'ing.

Box will be sanded inside and out, and painted black. With adjustable ports...32hz for daily and 50hz for burping. roughly 10ish cubes after displacements.

Share this post


Link to post
Share on other sites

Looking good Phil, I'm very interested in what you think of this setup. Great progress so far!

Share this post


Link to post
Share on other sites

Great!!! Someone said you were going sealed???LOL... what happened???

Share this post


Link to post
Share on other sites

I didn't think it was gonna be possible to do ported in the back. The Team NWSpl guys told me otherwise lol.

Share this post


Link to post
Share on other sites

I didn't think it was gonna be possible to do ported in the back. The Team NWSpl guys told me otherwise lol.

Mhmm! I'm excited for you!!

Share this post


Link to post
Share on other sites

box looks good so far!

Share this post


Link to post
Share on other sites
385649_394772557207584_100000245298129_1488212_1625611361_n.jpg

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×