Jump to content
Mac N Cheese

Mac N Cheese's build log

Recommended Posts

INSTALLED!!!

15.1v at idle.....full tilt doesn't drop below 14v :drink40::fing34:

now thats an alternator

more pics to come...to bad the alt. is absolutely hidden so you can't see the beauty....but i still gotta install a fuse holder and crimp the negitive line on the front bat.....

stay tuned

Share this post


Link to post
Share on other sites

INSTALLED!!!

15.1v at idle.....full tilt doesn't drop below 14v :drink40::fing34:

now thats an alternator

more pics to come...to bad the alt. is absolutely hidden so you can't see the beauty....but i still gotta install a fuse holder and crimp the negitive line on the front bat.....

stay tuned

that text made me extremely jelous

Share this post


Link to post
Share on other sites

The madness is about to begin.....again, well not to much. Remember i am not looking for a all out SPL setup, just a daily driver that is light on weight and still bangs...a solid 12 BL in a 2.0 cu ft enclosure~35Hz

equipment:

12 BL dual 1

Alpine MRP M1000 (yes i know, no subsonic filter blah....it was stuffed away in my closet so i wanna give it some use)

Knu Konceptz 4awg Kolossus cable

Sundown 100.4 (JL 6.5s, tweets)

Still need another set of components for the rear.

Also my enclosure is temporary due to the fact i dont know if my new car rear seats fold down......if they dont i know there is a armrest that connects to trunk. Maybe aeroport straight forward.

Previous setup (BTL 18m, sundown 3k..etc)

gallery_7108_326_850896.jpg

12 BL brushed alum :popcorn:

feels good to go back to a 12....

gallery_7108_326_374402.jpg

gallery_7108_326_383205.jpg

gallery_7108_326_676674.jpg

gallery_7108_326_4187.jpg

tomorrow it will be tested out in my brother car...going against a W7 :popcorn:

Found a type of car i am interested in but we will keep that a secret for now

Share this post


Link to post
Share on other sites

ohhhh.. i know i know.. and those e8;s look good. NOW GET THEM RECONED

i am working on it...remind me never to do a flush mount again! i have been sanding the front baffle for a couple hours now and still the BL will not sit in straight.....out of sandpaper and dont feel like buying a router. :No:

Share this post


Link to post
Share on other sites

Does that little fella think thats his new food bowl?

Share this post


Link to post
Share on other sites

picked up the necessary supplies from the local Lowes and ready to get started.

As of weather: high of 75, sunny with a breeze

Perfect!

Share this post


Link to post
Share on other sites

macncheese.jpg

6: Aero 18" long.

3.1cuft NET @33hz

Pay close attention-

The baffle, back and LEFT side are dual layered.

Share this post


Link to post
Share on other sites

internal height is 16.5", external - 18" single layered port side, top and bottom

Keep port's flare edge about 3-5" from the back wall

Share this post


Link to post
Share on other sites

internal height is 16.5", external - 18" single layered port side, top and bottom

Keep port's flare edge about 3-5" from the back wall

will do. Thanks Shiz,

Share this post


Link to post
Share on other sites

i have your other clamp here

haha i was looking for it! its all good, I found some other stuff around the garage

Share this post


Link to post
Share on other sites

i like all your work, mac

thanks, i appreciate it...enclosure is finished.

Am i the only person to seal a BL before?

Share this post


Link to post
Share on other sites

i applied a couple layers of speckled gray spray and i like the look of it. I am sick of using black with white specks so i thought i would change it up a bit. Plus i thought it would look nice with a giant ass black aeroport coming out of the side. Paint still has to dry for another hour and then ill be putting in the terminals, predrill the screws in for the BL.

gallery_7108_326_230423.jpg

Almost completed in a single day :popcorn:

Share this post


Link to post
Share on other sites

heres the spray I used..

gallery_7108_326_265523.jpg

Bolt terminals

gallery_7108_326_258118.jpg

Thought i would do alittle touch up of black textured around the corners..

gallery_7108_326_605789.jpg

gallery_7108_326_251421.jpg

gallery_7108_326_92692.jpg

Share this post


Link to post
Share on other sites

atta boy. when are you getting your car?

i think i found THE one! and its a killer deal so im hoping to purchase it tomorrow...already called and left my number. :woot:

the icons on here will be going nuts if i purchase it

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×