Jump to content
CarlosRodriguez

just paid for a zcon!What rms are you pushing yours at?? HELP

Recommended Posts

Well as the title says just payed for 2 12 inch zcons dual ones

The Car : 94 bmw 325i

Electrical : xs power d3100, xp3000, mechman 320 alt. 2/0 welding cable in the rear soon to be 4 more runs of kicker hyper flex 2+, 2- for a total of 6 if neededninja.gif

Amps: pair of planet audio bb2400.1 strapped @ 1 ohm (.5 per amp)

Subs: soon to be 2 12inch ZCONS smile.png dual 1

the question 1 : will this be enough power to push them ??

q 2: what do you guys, girls run to your zcons ??

q3 : how long was your build time for them ?? if you remember that is smile.png

any info is appreciated

Edited by djrockstar

Share this post


Link to post
Share on other sites

I ran a crescendo bc5500 to mine...so roughly 2600-2800 each

Expect 3-4 weeks before you get them...is a safe estimate

Share this post


Link to post
Share on other sites

Question #1- depends on your enclosure size, enclosure type and tuning

Question #2- Most people i've seen on here run speaker wire to their zcons. Some others run DMMs to them when they screw them up and others run CA glue on them when they are rebuilding them.

Question #3- I can't answer this one.. just gotta sit back and watch Titanic a couple hundred times back to back and then.... They'll be there.

q1:its going to be a trunk box so about 2.5 at most per sub around 35 hz

q2: lol thats good info on that speaker wire thing laugh.png what i ment to say is rms power wise per sub

q3: have to get the rental card out and pick it up then pass out for around a month

I ran a crescendo bc5500 to mine...so roughly 2600-2800 each

Expect 3-4 weeks before you get them...is a safe estimate

how big of a box do you have them in ?

and figured something like that

Share this post


Link to post
Share on other sites

I ran a crescendo bc5500 to mine...so roughly 2600-2800 each

Expect 3-4 weeks before you get them...is a safe estimate

I've run my Zcon 18 on 5k for sometime, but it takes some experience to run that much power without any problems. If you plan on running a ton of power make sure your box is on the small side.. I've learned this the hard way when upgrading power. Lower power = Big box, Lots of power = small box.

Current lead time is about 3 weeks excluding weekends.

Share this post


Link to post
Share on other sites

2.5ft3 is not horrible, but you can get by with less..around 2 - 2.25f3 net each would be just fine and work amazingly well.

Share this post


Link to post
Share on other sites

I'm running 1200 to mine in a 6cu box So I think you will be ok. But will be running 2500 soon. A few other members are running 5k (smartly) 3-4 weeks would be good estimate

Share this post


Link to post
Share on other sites

I'm running 1200 to mine in a 6cu box So I think you will be ok. But will be running 2500 soon. A few other members are running 5k (smartly) 3-4 weeks would be good estimate

Who are you talking too?

You quoted nobody!!!

Share this post


Link to post
Share on other sites

I ran a crescendo bc5500 to mine...so roughly 2600-2800 each

Expect 3-4 weeks before you get them...is a safe estimate

I've run my Zcon 18 on 5k for sometime, but it takes some experience to run that much power without any problems. If you plan on running a ton of power make sure your box is on the small side.. I've learned this the hard way when upgrading power. Lower power = Big box, Lots of power = small box.

Current lead time is about 3 weeks excluding weekends.

ahh thats better then 4 weeksdancingsmilie.gif

2.5ft3 is not horrible, but you can get by with less..around 2 - 2.25f3 net each would be just fine and work amazingly well.

gotcha trying to get a bit wider port then what i have probably going to build a in trunk box once i completely finish the electrical upgrades

I'm running 1200 to mine in a 6cu box So I think you will be ok. But will be running 2500 soon. A few other members are running 5k (smartly) 3-4 weeks would be good estimate

i plan on up grading to around a single 5 k once i get rid of these amps and subs (sa-12s) still dont know exactly to what atm though

Share this post


Link to post
Share on other sites

That only sounds better cus he said 3 weeks....excluding weekends.

My box was 8cf after displacement and tuned to 32hz...

Share this post


Link to post
Share on other sites

Thank you for your order, I just finished processing it (them). Current lead time is 3-4 weeks unfortunately due to the "busy season" of car audio being right now.

When the subs are due to ship, you will receive a store email with your tracking information.

As I am positive any SSA subwoofer owner will tell you, they are well worth the wait.

Share this post


Link to post
Share on other sites

Yes Mark I agree with you.

Share this post


Link to post
Share on other sites

Ihave had 2600rms going to my 1 15 in 4 cubed tuned at 30hz. Loves the power.

And yes. Its well worth the wait for them

Share this post


Link to post
Share on other sites

pictures of current stuff or this thread is worthless

Share this post


Link to post
Share on other sites

my bad i got caught up with work wonder why i never got email resposes hmm but here are some pictures of whats in there atm..

what i use to set my gains..

smddd-1revieew.jpg

the 320 amp alt

IMAG0768.jpg

IMAG0763.jpg

IMAG0765.jpg

the sa -12s box tuned to around 35 hz

IMAG0657.jpg

IMAG0451.jpg

my two batterys

IMAG0728.jpg

IMAG0733.jpg

2/0 welding cable

IMAG0745.jpg

IMAG0742.jpg

IMAG0743.jpg

IMAG0744.jpg

thats All i gots for now should be more to come as i get it

on a side note should i fiber glass the spare tire well into the intrunk box or would it cause more issues then benefits??

Share this post


Link to post
Share on other sites

that looks intense!!!

Share this post


Link to post
Share on other sites

nice stuff man im digging everything keep those pics coming

Share this post


Link to post
Share on other sites

Thanks I hope I can get it louder at least a lil bit .. smile.png

I don't think that will be a problem. wink.png

Share this post


Link to post
Share on other sites

I'm thinking this is going to be the next box any input suggestions?

Also this box will be fiber glassed inside, resin a matt

gross volume 7.18

port area 70 in^2

port area per ft 12.30 in^2

net volume 5.69 (2.845 per sub)

tune 37.62 hz

IMAG0785.jpg

IMAG0786.jpg

IMAG0787.jpg

Edited by djrockstar

Share this post


Link to post
Share on other sites

the zcon Have Arrived smile.pngadhd.gifpopcorn2.gif although i seen the Dam ups guy drop it off his truck from the top step in the front it rolled and my heart Dropped sad.png but i inspected it and its seem a ok angry2.gifjon.gif

here are some pictures

didnt know to start a build log or maybe a mod can move thiss?? anyways onto the pics of the new STUFF lol

IMAG0025.jpg

IMAG0026.jpg

IMAG0037.jpg

IMAG0038.jpg

IMAG0036.jpg

IMAG0035.jpg

IMAG0033.jpg

IMAG0031.jpg

IMAG0028.jpg

New New radio lol

IMAG0041.jpg

and a 6 inch aero smile.png new box being built tomorrow

IMAG0042.jpg

Share this post


Link to post
Share on other sites

Looks awesome man! You are only using one 6" port?

Share this post


Link to post
Share on other sites

the zcon Have Arrived smile.pngadhd.gifpopcorn2.gif although i seen the Dam ups guy drop it off his truck from the top step in the front it rolled and my heart Dropped sad.png but i inspected it and its seem a ok angry2.gifjon.gif

I would've been soooooo pissed. Glad it's ok though.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×