Jump to content
oakteg21

need assistance in designing a box for a 10" ssd on a HB foxbody m

Recommended Posts

Looking to get help on designing a box for a 10" ssd on a hatchback fox body mustang. This is for daily use by my gf. And would like help if possible from someone that is familiar with fox body mustangs hatches as they are small. Can someone please help im interested and having the box tuned to about 32 or 33hz.

Share this post


Link to post
Share on other sites

I can try to help you out. Is it gonna be a weird box?

Share this post


Link to post
Share on other sites

No just want to build a simple sub up port back enclosure

Share this post


Link to post
Share on other sites

Okk I just need the amount of power you're going to run, max dimensions, and link to sub page.

Share this post


Link to post
Share on other sites

pics of said car please? i had one and loved it! there is plenty of room right behind the back seat to do a very nice ported enclosure. Nothing odd shaped about it. Go out and measure the width between the wheel wells though and report back

Share this post


Link to post
Share on other sites

Ok will do so i will be using a Rockford fosgate prime 1200.1amp on a 10"fi ssd.

Share this post


Link to post
Share on other sites

Its been a while ive been here because issues with my dealership being sold and ending up with no job but was rehired with the buying dealership owner so ffeeling relieved now anyways im still looking for the box design for a 10" fi ssd i will be installing on my gfs car its fully loaded. Help will be greatly appreciated i know its a small hatch hope someone is able to help me trunk dimensions i dont have and cant get them so if someone has them it will be really appreciated if they can share them. Thanks.post-24474-0-70965900-1404597568_thumb.j

Share this post


Link to post
Share on other sites

Can't build a box without dimensions. Only takes a few minutes to measure. Go jman.gif

Share this post


Link to post
Share on other sites

I would if it was with me lol but my gf owns it and i hardly even get to see her thats why i was hoping someone might have demensions but a wild guess maybe 12" height, 19" l ength and 30" width

This sub doesnt require much room on its enclosure for optimum performance for a dd. I would want the design to be sub up port back for sure if someone could help with the design.

Edited by oakteg21

Share this post


Link to post
Share on other sites

I would if it was with me lol but my gf owns it and i hardly even get to see her thats why i was hoping someone might have demensions but a wild guess maybe 12" height, 19" l ength and 30" width

This sub doesnt require much room on its enclosure for optimum performance for a dd. I would want the design to be sub up port back for sure if someone could help with the design.

Without dimensions we are little help.

Share this post


Link to post
Share on other sites

If she can't spend 20 seconds with a tape measure then fuck it.

Share this post


Link to post
Share on other sites

So managed to squeeze a few minutes for tomorrow before she goes to work. I will have measurements tomorrow morning. Hope someone is able to help.

Share this post


Link to post
Share on other sites

Alright guys managed to measure the trunk very small trunk hopefully we can get a design that will give us optimum performance of the sub at 32hz and take the least possible trunk space. The reason why I choose this sub because it doesn't require much room for optimum performance. So whole trunk wise i measured 29.5" in depth, 37" in length, and height 11" but cover goes down to about 6" and i would like to keep the cover so i can use it to cover the sub when im not around. Like to use the length more then depth to keep more trunk space available so dont mind a low long sub enclosure. Sub up port back set up will be ideal for me. Hope someone can help out.

Edited by oakteg21

Share this post


Link to post
Share on other sites

Something like this?  1.2 net cubes,  ~23" of port(6.5" x 3.5" x 44"),  33hz(Fi Recomended)

 

post-40683-0-13643200-1404774156_thumb.j

Edited by Leedogg

Share this post


Link to post
Share on other sites

Something like this? 1.2 net cubes, ~23" of port(6.5" x 3.5" x 44"), 33hz(Fi Recomended)

Capture.JPG

Yes! Thats awesome!! Does your calculation software generate a cut sheet with it???

Share this post


Link to post
Share on other sites

Can someone help and also pm me a cutsheet if you can? Thanks.

Share this post


Link to post
Share on other sites

Not to hard to figure out the cut sheet from that picture.

Share this post


Link to post
Share on other sites

Not to hard to figure out the cut sheet from that picture.

Dont have prior knowledge on how to build a box. My uncle usually builds them for me.

Share this post


Link to post
Share on other sites

Not to hard to figure out the cut sheet from that picture.

Dont have prior knowledge on how to build a box. My uncle usually builds them for me.

he could probably figure out the cuts from that picture if you could show him. . But I'm sure you could pm the guy that did the design and he could give you the cut sheet

Share this post


Link to post
Share on other sites

Will try that thanks because i have no prior knowledge building boxes or designing them i tried before and failed miserably

Share this post


Link to post
Share on other sites

I'll work up a cut list for you...but it'll be next wednesday before I m back to work where I have the file at.

Share this post


Link to post
Share on other sites

Why don't you try yourself and then ask to see how it is? Spoon feeding doesn't help anyone.

Share this post


Link to post
Share on other sites

I'll work up a cut list for you...but it'll be next wednesday before I m back to work where I have the file at.

No rush i really appreciate it.

Share this post


Link to post
Share on other sites

Why don't you try yourself and then ask to see how it is? Spoon feeding doesn't help anyone.

Thats true, havent had much time at all now that the dealership i worked for has been sold and more then half of the employees werent rehired to the new owners company but a handfull of techs including myself have to work 6 days a week opening to closing and not to mention i have school after work. But i wil try to squeeze some time to try it out.

Edited by oakteg21

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×