Jump to content
altoncustomtech

Anyone ever heard of/used Percy's HyperFiber?

Recommended Posts

I searched the forum for any previous posts and information on this and came up empty handed so I apologize if this has been covered before.  I finally talked to my buddy about the fiberglass stuff he was talking about that came ready to go, all you had to do was mold it around whatever it was you were using it on and let it cure.  I found out that it actually cures in sunlight, or under UV light and has a wire mesh in it to help it hold it's shape.

 

It's not horribly expensive either.  I found 1 sq.ft. pieces for $24 at Jeg's of all places which I didn't think was too unreasonable considering it's got everything a person needs to make it work.  I would imagine that by the time a person bought enough resin, hardener, molding supplies, glass mat, etc. to do the little sail panel pods I'm wanting to do that it would cost more than $48.  Maybe not, but for the location and shape these are going to have to have at least doing the main part of the pod would likely be easier with the Hyperfiber.

 

 

This is a subject I know VERY little about so some insight and help would be greatly appreciated by anyone who has fiberglass experience and especially experience with this product.

Share this post


Link to post
Share on other sites

I've sent an email to the manufacturer hoping to get some literature on the products.  I've watched a few videos on the same/similar products and it looks like it can do just what I'm looking for it to do.  

Share this post


Link to post
Share on other sites

Have you heard of pre-preganated materials?  This is that, but instead of using heat to cure, this uses UV.  I am glad you posted this as I was holding off my fiberglass work due to the cold.   Now, I can do it in this crap!  Great find!

Share this post


Link to post
Share on other sites

i think twistedchild 420 has a video on youtube of him using something like this

Share this post


Link to post
Share on other sites

Have you heard of pre-preganated materials?  This is that, but instead of using heat to cure, this uses UV.  I am glad you posted this as I was holding off my fiberglass work due to the cold.   Now, I can do it in this crap!  Great find!

 

I hadn't before my buddy had informed me of it.  This stuff should be available everywhere from everything I've found on it so far.  I can't wait to try the stuff out.

 

 

i think twistedchild 420 has a video on youtube of him using something like this

 

I've found several videos on it and they all tell me the same thing, "GO FOR IT!!"  lol...

 

I got the email back from the manufacturer and unfortunately the Percy's brand product is no longer being made so I'll have to go with another brand.

Share this post


Link to post
Share on other sites

There's always the smd sunflash stuff that cures via uv. But most people don't want to support him.

Share this post


Link to post
Share on other sites

Smd uv crap!

Share this post


Link to post
Share on other sites

Smd uv crap!

sigh.gif

It's no crap, it's just company that didn't want to go trough selling it themselves so they asked him to sell it instead.

Edited by kirill007

Share this post


Link to post
Share on other sites

Saw an article about a similar pre-preganated fiberglass material about 2 years ago in Hot Rod magazine. The cost stated in the article was a lot higher which is why I assumed it hadn't caught on, but maybe now that it's becoming more available the prices are coming down.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.

    1. Recent Topics

        • 17 comments
        • 178 views
        • 393 comments
        • 32,175 views
        • 2 comments
        • 670 views
        • 5 comments
        • 1,446 views
        • 6 comments
        • 1,015 views
        • 1 comment
        • 961 views
  • Similar Content

    • By Jacob Eshack
      Hey guys, I have e12 d2 I got a while back from Jacobs yard sale, I was thinking it would make a decent home theater sub, Just want some ideas on tuning/aero port/ down firing?/ If anyone can help out Id appreciate

    • By mklett33
      Hey all! Much like my previous threads I am starting another part of a build that will be completely documented through video. The support for the door pod series was awesome and I hope you guys enjoy this series just as much. Just like before I will be video taping every single step and editing all the information together to present to you. If you haven't seen my videos before I hope that you enjoy them and would love to hear what you think!
       
      If you missed the seeing the door pods I mentioned above here is how they turned out:
       
      http://www.youtube.com/caraudiofabrication'>
       
      If you would like to see the in depth process of each step for how I made these door pods there is a conveniently organized playlist on YouTube at this link:
       

       
      But enough about the door pods! Its time to get into our next project: The Fiberglass Under Seat Sub Box! Lets get started!
       
      First a little about the system:
       
      The Vehicle:
      Chevy Duramax 2500 HD Extended Cab (Will add pics soon)
       
      The Gear:
      Alpine Type R's 6.5" Component Speakers
      10" JL Audio W3 (Just kidding, I was planning on using this but have fallen in love with the DAD KMH-8, so we are using that instead)
      Knukonceptz wiring
      Wirecare.com wire protection products
      Alpine MRP-M500
      Alpine MRP-F300
       
      If you are interested in a review for the KMH-8 or learning more, check this out:

       
      I started with a concept, I knew that I wanted to build a box that would house both the amplifiers for the system and hide the wiring, but at the same time I wanted quick and easy access to them. The plan for how I am going to do this is difficult to explain, but as the build progresses it will become clear. 
       
      The box will also feature several inserts, I have entertained the idea of doing light up plexi on parts of the box. But I am not sure I want too. What do you guys think?
       
      Anyhow here is the initial idea, I like to get stuff out on paper first, really gets the creative juices flowing:
       
      http://www.youtube.com/caraudiofabrication'>
       
      With the general idea framed out I started building. Pretty traditional stuff here but one of the coolest things I can teach you here is how I used a "Adjustable Curve" to get a perfect match with the floor contour of the vehicle. I also got the "Beauty Panel" frame trimmed out on the top of the box.
       
      http://www.youtube.com/caraudiofabrication'>
       
      To see the steps that got me to this point check out the video below!
       

       
      Well, thats it for now, off to a good start, I already have the bottom fiberglass molded, just need to edit the video, so you guys have to wait!    Let me know what you guys think, wondering what direction you think I should go with the insert pieces, back lit, metal mesh, etc.
    • By mklett33
      In this tutorial write up we will be covering how to create some awesome door panel pods that will add a custom look to your install, allow you to integrate multiple speakers into a door panel, and allow you to control the mounting position of the speakers. Note that while these are in fact door “pods” that are not actually permanently bonded are made as part of the door panel itself, there are many techniques within that could be used if you were in fact planning on creating door “panels” from scratch. Let’s begin!
       
       
      Step 1: Woodwork and Templates:
       

       
      In order to have a good foundation for our door pods we want to make awesome speaker rings. The video above covers many of the details needed.  Take your time with this step as clean woodwork is essential to having a good foundation to create the door pods.
       
      Tools needed:
      Router
      Jig Saw
      Jasper Circle Jig
      Flush Trim Bit
      Rabbeting Bit
      Foam Tape
      LTP
      Stapler and Staples
       
      Upon completion you should have great looking speaker templates that are prepped for molding into the panel.
       

       

       
       
      Step 2: Reverse Mounting Speakers:
       

       
      This step is not essential in terms of design, but it is important to have a plan for exactly how the speakers will mount. The last thing we want is to make these amazing door panels and use wood screws to secure the speakers that will become loose with time. Take a look at the fasteners we used here instead.
       
      Tools Needed:
      Drill and Bits
      Marker
       
      When complete your speakers will be ready to mount securely to your pods.
       

    • By Trent Hari
      I would like help with a design of a box for a Sundown Audio SA 12" sub woofer , that is 12"  at the bottom, 8" at the top 17" tall and 30" long, with the sub woofer mounted on the slanted side. I would like it to be ported, and tuned to 32 HZ.
       
      Again,
      3/4" MDF 
       
      12" bottom
      8" top
      17" tall
      30" long
       
      Tuned to 32 HZ
       
      Sub-woofer mounted on slanted side
       
      Truck-box style.
       
       
       
  • Recent YouTube Posts

×