Jump to content
Sign in to follow this  
shizzzon

Taramp's Group Buy Amps, processors, etc...

Recommended Posts

Taramp's Official Group Buy

 

The Group Buy will end February 16, 2014 11:59pm EST on a Sunday night.

 

We expect all orders to come in and ship out domestically between week one and two of March. We expect all orders to be delivered to customers in the Group Buy before SBN 2014 which is March 22-23, 2014.

 

All prices set below for immediate payment include shipping and is good for the lower 48 states. Shipping to Alaska, Hawaii, other territories of the US and all International orders are subject for custom shipping quotes which shall be done via contacting me at- shizzzon@gmail.com

 

All amplifiers (unless otherwise noted) come with custom Wire inputs used to run extra or larger cables to amp to prevent unwanted voltage drop.  

It IS POSSIBLE that some amps may not have their inputs manufactured on time(mid March).  If this happens, we will let you know and ship them out for free immediately after receiving them.  

We just want to let everyone know this just in case our deadline is not met.

 

Warranty coverage is 1yr from manufactured date.

 

We offer alternate warranty coverage that is described in this link-


 

And now, the pricing-

 

HD Series

Full Range SMD(Surface-Mounted Device) Technology based Class D amps.

These amps range from 5Hz-10HZ - 15KHz, Power rated at 0.3-0.5% THD and have on-board subsonic, low pass and bass boost* with efficiency ranges in the 72-78% range at low ohm stability range.

 

When placing your order, PLEASE put into text field which ohm stability version you wish to purchase!  The power rating next to the amp model will be it's capability at specified ohm version.

IE- 1,439w amp can be built for 1 or 2ohm rating.  Certain amps may or may not have additional ohm versions but ALL versions will be listed next to each amp.

Power supply range- 10.5v-16vDC

 

HD8000

9,595w @13.8v @0.5% THD

Ohm versions- 1 or 2 ohm

Dimensions (WxHxD): 9.02" X 2.56" X 19.57" 

Weight: 13.47lbs

Wire input adapter- Triple 1/0 - 4/0 Insert with Protective Insulation

Price- $795 shipped PayPal-IntegrationPage-PaymentBTN-BuyNow

 

HD6500

7,796w @13.8v @0.3% THD

Ohm versions- 1 or 2 ohm

Dimensions (WxHxD): 9.02" x 2.56" x 18.82" 

Weight: 11.46lbs

Wire input adapter- Triple 1/0 Insert with Protective Insulation

Price- $729 shipped PayPal-IntegrationPage-PaymentBTN-BuyNow

 

HD5000

5,997w @13.8v @0.3% THD

Ohm versions- 1 or 2 ohm

Dimensions (WxHxD): 9.02" x 2.56" x 17.6" 

Weight: 11.44lbs

Wire input adapter- Triple 1/0 Insert with Protective Insulation

Price- $659 shipped PayPal-IntegrationPage-PaymentBTN-BuyNow

 

HD4000

4,798w @13.8v @0.3% THD

Ohm versions- 1 or 2 ohm

Dimensions (WxHxD): 9.02" x 2.56" x 14.76" 

Weight: 9.08lbs

Wire input adapter- Triple 1/0 Insert with Protective Insulation

Price- $615 shipped PayPal-IntegrationPage-PaymentBTN-BuyNow

 

HD3000

3,598w @13.8v @0.3% THD

Ohm versions- 1 or 2 ohm

Dimensions (WxHxD): 9.02" x 2.56" x 11.34" 

Weight: 6.86lbs

Wire input adapter- 4awg to 1/0 terminal

Price- $469 shipped PayPal-IntegrationPage-PaymentBTN-BuyNow

 

HD2500

2,998w @13.8v @0.3% THD

Ohm versions- 1 or 2 ohm

Dimensions (WxHxD): 9.02" x 2.56" x 9.53" 

Weight: 5.73lbs

Wire input adapter- 4awg to 1/0 terminal

Price- $425 shipped PayPal-IntegrationPage-PaymentBTN-BuyNow

 

HD1600

1,919w @13.8v @0.3% THD

Ohm versions- 1, 2 or 4 ohm

Dimensions (WxHxD): 9.02" x 2.56" x 9.53"

Weight: 5.52lbs

Wire input adapter- 6awg to 1/0 terminal

Price- $376 shipped PayPal-IntegrationPage-PaymentBTN-BuyNow

 

HD1200

1,439w @13.8v @0.3% THD

Ohm versions- 1 or 2 ohm

Dimensions (WxHxD): 9.02" x 2.56" x 8.08"

Weight: 4.37lbs

Wire input adapter- Unavailable

Price- $332 shipped PayPal-IntegrationPage-PaymentBTN-BuyNow

 

HD800

959w @13.8v @0.5% THD

Ohm versions- 1 or 2 ohm

Frequency Range- 20Hz - 30KHz

Dimensions (WxHxD): 7.68" x 2.2" x 7.91"

Weight: 3.53lbs

Wire input adapter- Unavailable

Price- $295 shipped PayPal-IntegrationPage-PaymentBTN-BuyNow

 

HD400.4S

All ratings are at 0.02%THD at 13.8v

Ohm versions- 2 ohm only

4x100w @2Ω / 2x100w @2Ω + 1x200w @4Ω

4x60w @4Ω / 2x200w @4Ω / 2x60w @4Ω + 1x120w @8ohm

4x33w @8Ω / 2x120w @8Ω / 2x33w @8Ω + 1x66w @16ohm

Frequency Range- 10Hz - 38KHz

HPF / LPF Fixed @80Hz

Dimensions (WxHxD): 5.94" x 2.01" x 7.99"

Weight: 1.4lbs

Wire input adapter- Unavailable

Price- $174 shipped PayPal-IntegrationPage-PaymentBTN-BuyNow

 

T Series

Besides the T500, this line is Taramp's extreme high output series with efficiency ranges from 71-89% at 1ohm(and at 1 or 2ohm on T500). These amps are also full range for use for bass and midbass\range as well going up to 5KHz with subsonic and low pass filter.

All power ratings based on 12.6v with power supply voltage range from 10.5-15.0v.

 

T20.2KW

20,200w @0.3%THD

23,800w @13.8v

Frequency Range- 5Hz - 5KHz

Ohm versions- 1 ohm only

Dimensions (WxHxD) - 11.46" x 2.2" x 28.74" 

Weight: 31.09lbs

Wire input adapter- Triple 1/0 - 4/0 Insert with Protective Insulation

Price- $1829 shipped PayPal-IntegrationPage-PaymentBTN-BuyNow

 

T14.2KW

14,200w @0.3%THD

16,800w @13.8v

Frequency Range- 5Hz - 5KHz

Ohm versions- 1 ohm only

Dimensions (WxHxD) - 11.46" x 2.2" x 28.74"

Weight: 29.76lbs

Wire input adapter- Triple 1/0 - 4/0 Insert with Protective Insulation

Price- $1659 shipped PayPal-IntegrationPage-PaymentBTN-BuyNow

 

T10.9KW

10,900w @0.3%THD

12,890w @13.8v

Frequency Range- 5Hz - 5KHz

Ohm versions- 1 ohm only

Dimensions (WxHxD) - 11.46" x 2.2" x 24.88"

Weight: 22.71lbs

Wire input adapter- Triple 1/0 - 4/0 Insert with Protective Insulation

Price- $1399 shipped PayPal-IntegrationPage-PaymentBTN-BuyNow

 

T500D

500w @0.5%THD

599w @13.8v

Frequency Range- 20Hz - 30KHz

Ohm versions- 1 or 2 ohm

Bass Boost

HPF / LPF fixed at 100Hz

Dimensions (WxHxD) - 8.27" x 6.61" x 2.05"

Weight: 2.65lbs

Wire input adapter- Unavailable

Price- $189 shipped PayPal-IntegrationPage-PaymentBTN-BuyNow

Edited by shizzzon

Share this post


Link to post
Share on other sites
TS Series

This line of amplifiers come in 2 or 4 channels. These amps come in 1ohm or 2ohm stability models and all ratings below are of 1ohm model. Expect slightly higher efficiency with 2ohm models.

All amps in the TS line use FIXED Crossover points.

Power supply range- 10v-16vDC

 

T1300x2

Rated Measurement- 13.8v @0.45%THD

2x780w @1/2ohm

2x468w @2/4ohm / 1x1559w @2/4ohm

2x257w @4/8ohm / 1x935w @4/8ohm

1x514w @8/16ohm

Frequency Range- 15Hz - 38KHz

Ohm versions- 1 or 2 ohm

Efficiency- 80%

Power Supply- 9vDC minimum

Bass Boost

HPF / LPF fixed at 100Hz

Dimensions (WxHxD): 7.68" x 2.2" x 12,2"

Weight: 4.87lbs

Wire input adapter- Optional $20 (6awg to 1/0), not included

Price- $359 shipped PayPal-IntegrationPage-PaymentBTN-BuyNow

 

T1200x4

Rated Measurement- 13.8v @0.5%THD

4x360w @1/2ohm

4x237w @2/4ohm / 2x720w @2/4ohm

4x130w @4/8ohm / 2x474w @4/8ohm

2x260w @8/16ohm

Frequency Range- 20Hz - 30KHz

Ohm versions- 1 or 2 ohm

Efficiency- 80%

Bass Boost

HPF / LPF fixed at 100Hz

Dimensions (WxHxD): 7.68" x 2.2" x 14.25"

Weight: 6.06lbs

Wire input adapter- Optional $20 (6awg to 1/0), not included

Price- $399 shipped PayPal-IntegrationPage-PaymentBTN-BuyNow

 

T800x4

Rated Measurement- 13.8v @0.5%THD

4x240w @1/2ohm

4x150w @2/4ohm / 2x480w @2/4ohm

4x72w @4/8ohm / 2x300w @4/8ohm

2x144w @8/16ohm

Frequency Range- 20Hz - 40KHz

Ohm versions- 1 or 2 ohm

Efficiency- 78%

Bass Boost

HPF / LPF fixed at 100Hz

Dimensions (WxHxD): 7.68" x 2.2" x 12.44"

Weight: 5.18lbs

Wire input adapter- Unavailable

Price- $319 shipped PayPal-IntegrationPage-PaymentBTN-BuyNow

 

T600x4

Rated Measurement- 13.8v @0.45%THD

4x180w @2ohm

4x108w @4ohm / 2x360w @4ohm

4x60w @8ohm / 2x216w @8ohm

2x120w @16ohm

Frequency Range- 10Hz - 40KHz

Ohm versions- 2 ohm only

Efficiency- 80%

HPF / LPF fixed at 100Hz

Power Supply- 9vDC minimum

Dimensions (WxHxD): 6.61" x 2.13" x 10.04"

Weight: 3.35lbs

Wire input adapter- Unavailable

Price- $249 shipped PayPal-IntegrationPage-PaymentBTN-BuyNow

 

T400x4

Rated Measurement- 13.8v @0.05%THD

4x100w @2ohm

4x63w @4ohm / 2x200w @4ohm

2x126w @8ohm

Frequency Range- 20Hz - 30KHz

Ohm versions- 2 ohm only

Efficiency- 80%

HPF / LPF fixed at 90Hz

Power Supply- 8vDC minimum

Dimensions (WxHxD): 5.28" x 1.65" x  7.99"

Weight: 1.96lbs

Wire input adapter- Unavailable

Price- $179 shipped PayPal-IntegrationPage-PaymentBTN-BuyNow

 

T150x2

Rated Measurement- 13.8v @0.05%THD

2x75w @2ohm

2x45w @4ohm / 1x150w @4ohm

2x25w @8ohm / 1x90w @8ohm

1x50w @16ohm

Frequency Range- 18Hz - 40KHz

Ohm versions- 2 ohm only

Efficiency- 80%

HPF / LPF fixed at 100Hz

Dimensions (WxHxD): 6.54" x 2.01" x 3.62"

Weight: 1.12lbs

Wire input adapter- Unavailable

Price- $109 shipped PayPal-IntegrationPage-PaymentBTN-BuyNow

 

Crossovers

 

CRX2

Channels - 2

Subsonic Filter: Variable Bypass /20/60/80Hz (-24dB/ 8deg 4deg order Linkwitz-Riley )

Bass Boost: 0 to 10 dB (40Hz)

Low Pass Filter: Variable from 100Hz to 10KHz (-12dB/ 8deg 2deg order Butterworth)

High Pass Filter: Variable from 100Hz to 10KHz (-12dB/ 8deg 2deg order Butterworth)

Input Impedance: 27K ohms

Output Impedance: 440 ohms

Maximum Input L/R: 4.57 V RMS @ 15.4 dBu

Output Level L/R: 9.3 V RMS @ 21.6 dBu

Max. Output of the Pass Thru L/R: 9.3 V RMS @ 21.6 dBu

Frequency Response: (-1dB) of 10Hz to 100KHz

Total Harmonic Distortion (THD): < 0.01% at 1KHz

Crosstalk (Separation between channels): >90dB

Power Supply Voltage: 10 to 16 VDC

Nominal Consumption: 250mA @ 12.6 Vdc

Protection: Reverse Polarity and short circuit

Dimensions (WxHxD): 6.18" x 1.65" x 5.71" 

Weight: 1.01lbs

Price- $134 shipped PayPal-IntegrationPage-PaymentBTN-BuyNow

 

CRX4

Electronic Crossover 12dB/ 8nd with 4 channels

 

LOW: With variable cut(LPF) from 45 to 275Hz and bass enhancement of 6dB ( "bass boost") adjustable from 20 to 65Hz

MID-LOW: With initial cut (HPF) variable from 25Hz to 140Hz and final cutting (LPF) variable from 300Hz to 7.5KHz

MID-HIGH: With initial cut (HPF) variable 200Hz to 4.6KHz and final cutting (LPF) variable of 1.2KHz to 12KHz

HIGH: With variable cut (HPF) of 550Hz to 12KHz

Individual level Controls for channel

Track LOW and MID-LOW mono, with independent inputs

Tracks HIGH AND MID-HIGH stereo, separated from inputs LOW and MID-LOW

Dimensions: 7.48" x 5.71" x 1.58" (L x W x H) 

Weight: 1.24lbs

Price- $159 shipped PayPal-IntegrationPage-PaymentBTN-BuyNow

 

CRX5 Plus

Quantity of channels - 4 + 1 Pass Thru

Track Pass Thru (R L)

Phase Selectable: 0/180 Degrees

Variable Level: -infinity to 6dB

Via Low (R L) Mono

Subsonic Filter: Selectable (Bypass 40/60/80Hz ) (-24dB/ 8nd) butterworth

Low Pass Filter: Variable from 100Hz to 2KHz (-12dB/ 8nd Linkwitz-Riley )

Bass Boost: Variable 0 to 10 dB (40Hz)

Phase Selectable: 0/180 Degrees

Variable Level: -infinity to 10dB

Via Low Mid (R L) Mono

High Pass Filter: Variable from 30Hz to 600Hz (-12dB/ 8nd Linkwitz-Riley )

Low Pass Filter: Variable from 600Hz to 10KHz (-12dB/ 8nd Linkwitz-Riley )

Phase Selectable: 0/180 Degrees

Variable Level: -infinity to 10dB

Track High Mid (R and L) Stereo

High Pass Filter: Variable from 400Hz to 3KHz (-12dB/ 8nd Linkwitz-Riley )

Low Pass Filter: Variable from 5KHz to 20KHz (-12DB/ 8nd Linkwitz-Riley )

Phase Selectable: 0/180 Degrees

Variable Level: -infinity to 10dB

Track High (R and L) Stereo

High Pass Filter: Variable from 2KHz to 10KHz (-12dB/ 8nd Linkwitz-Riley )

Phase Selectable: 0/180 Degrees

Variable Level: -infinity to 10dB

Input Impedance: 10K Ohms

Output Impedance: 470 Ohms

Maximum Input Level R/L: 4.57 V RMS @ ( 15.4 dBu)

Maximum Level of Output R/L: 9.3 V RMS @ ( 21.6 dBu) 

Max Output Level of Pass Thru R/L: 9.3 V RMS @ ( 21.6 dBu)

Frequency Response: (-1dB) of 10Hz to 100KHz

Total Harmonic Distortion (THD): < 0.01% at 1KHz

Crosstalk (separation between channels): >85dB

Power Supply Voltage: 10.5 to 16 VDC

Nominal Consumption: 420mA @ 12.6 Vdc

Protection: Inversion of Polarity

Dimensions (WxHxD): 9.37" x 1.65" x 5.71" 

Weight: 1.54lbs

Price- $189 shipped PayPal-IntegrationPage-PaymentBTN-BuyNow

 

DTX 2.4s

Quantity of channels - 4

Filters: Per DSP, 24-bit/ 48KHz, (-24dB/ 8th) - 4TH order (Butterworth)

VIA LOW (L/R)

cut-off Frequency (HPF): 9 preset adjustments 20/25/30/35/40/45/50/55/60Hz

cut-off Frequency (LPF): 19 preset adjustments 60/70/80/90/100/110/125/140/160/180/200/225/250/280/320/360/400/450/500Hz

TRACK LOW MID (L/R)

cut-off Frequency (HPF): 11 preset adjustments 60/70/80/90/100/110/125/140/160/180/200Hz

cut-off Frequency (LPF): 25 preset adjustments 200/225/250/280/320/360/400/450/500/570/640/720/800/900/1K/1.1K/1.2K/1.4K/1.6K/1.8K/2K/2.2K/2.5K/2.8K/3.2KHz

TRACK HI MID (L/R)

cut-off Frequency (HPF): 21 preset adjustments 200/225/250/280/320/360/400/450/500/570/640/720/800/900/1K/1.1K/1.2K/1.4K/1.6K/1.8K/2KHz

cutoff Frequency (LPF): 9 preset adjustments 5.1K/5.7K/6.4K/7.2K/8.1K/9.1K/10K/11K/12KHz

VIA HIGH (L/R)

cut-off Frequency (HPF): 17 preset adjustments 2K/2.2K/2.5K/2.8K/3.2K/3.6K/4K/4.5K/5.1K/5.7K/6.4K/7.2K/8.1K/9.1K/10K/11K/12KHz

Input Impedance: 18K ohms

Output Impedance: 470 ohms

Maximum Input L/R: 4.0 V RMS @ ( 14 Dbu)

Maximum Level of Output L/R: 4.0 V RMS @ ( 14 dBu)

Frequency Response: 20Hz to 23KHz (-3dB)

Total Harmonic Distortion (THD): < 0.01% at 1KHz

Signal / Noise Ratio: >90dB

Crosstalk (separation between channels): >80dB

Power Supply Voltage: 10 to 16 VDC

Nominal Consumption: 0.50A @ 12.6 Vdc

Protection: Reverse Polarity and short circuit

Dimensions (WxHxD): 9.76" x 1.65" x 5.32"

Weight: 1.52lbs

Additional Functions: Adjustments of phase, gain, alignment and mute

Price- $229 shipped PayPal-IntegrationPage-PaymentBTN-BuyNow

Share this post


Link to post
Share on other sites
Equalizers

 

DEQ-1000

Frequency Selection:

15 Bands separated by 2/3 octave (25Hz, 40Hz, 63Hz, 100Hz, 160Hz, 250Hz, 400Hz, 630Hz,

1KHz, 1.6KHz , partials close , 6.3KHz , 4KHz, 10KHz, 16KHz) Mitigation

/ Enhancement: up to 12dB in steps of 0.5dB

Signal / Noise Ratio: >100 dB

Crosstalk (separation between channels): >85dB

THD: < 0.01%

Frequency Response: 15Hz to 23KHz (-3dB)

Maximum Level of Input Signal: 2.0V RMS

Maximum Level of Output Signal: 2.0V RMS

Input Impedance: 22K OHMS

Output Impedance: 330 OHMS

Operating Voltage: 8V to 16V DC

Maximum Consumption: 400mA

Dimensions (WXHXD): 7.6" x 1.7" x 4.72" 

Weight: 0.68lbs

 

Additional Functions:

Limiter with 6 levels of attenuation: (-3dB/ -6dB/ -9dB / -12dB / -15dB / -18dB)

Filter HPF (subsonic): (Fc = 30Hz / 40Hz / 50Hz / 60Hz / 70Hz / 80Hz) with attenuation of

24dB/ 8nd

Filter LPF: (Fc = 500Hz / 1KHz / of 1.5khz / 2KHz / partials close ) with attenuation of 12dB/ 8nd

screen Saver with VU

VU Bargraph leds with TI CLIP

Price- $229 shipped PayPal-IntegrationPage-PaymentBTN-BuyNow

 

Power Supplies

 

TEF-30A

Dual voltage Power Supply: automatic (127 / 220V AC)

Operational range 127V: 100 to 140V AC

Operational range 220V: 200 to 240V AC

Rated Current max. output: 30 Amps

Efficiency: 85% Consumption

Maximum Current Draw 127V: 5.6 Amps

Maximum Current Draw 220V: 4.0 Amps

Maximum Floatation at full load (30A @ 12.6V): < 3%

Input Fuse (internal): 10A, quick action

Dimensions (WxHxD): 6.54" x 2.05" x 5.71"

Weight: 2.36lbs

Price- $229 shipped PayPal-IntegrationPage-PaymentBTN-BuyNow

 

TEF-50A

Dual voltage Power Supply: automatic (127 / 220V AC)

Operational range 127V: 105 to 140V AC

Operational range 220V: 210 to 240V AC

Rated Current max. output: 50 Amps

Efficiency: 85% Consumption

Output Voltage (Selectable): 12.6/ 13.8v/ 14.4vDC

Maximum Current Draw 127V: 8.0 Amps

Maximum Current Draw 220V: 5.0 Amps

Maximum Floatation at full load (50A @ 12.6V): < 3%

Input Fuse (internal): 10A, quick action

Dimensions (WxHxD): 10.55" x 2.83" x 6.22"

Weight: 5.51lbs

Price- $339 shipped PayPal-IntegrationPage-PaymentBTN-BuyNow

 

TEF-100A

Dual voltage Power Supply: automatic (127 / 220V AC)

Operational range 127V: 105 to 140V AC

Operational range 220V: 190 to 240V AC

Rated Current max. output: 100 Amps

Efficiency: 85% Consumption

Output Voltage (Selectable): 12.6/ 13.8v/ 14.4vDC

Maximum Current Draw 127V: 16.5 Amps

Maximum Current Draw 220V: 12.8 Amps

Maximum Floatation at full load (100A @ 12.6V): < 3%

Protection Threshold against overload/ short outlet: 120A

Dimensions (WxHxD): 10.55" x 2.83" x 11.42"

Weight: 9.48lbs

Price- $449 shipped PayPal-IntegrationPage-PaymentBTN-BuyNow

 

TW Master/Slave

CHARACTERISTICS OF the TRANSMITTER (TW-MASTER):

Operational Range of Radio Frequency: 2.4GHz ISM band (2.404GHz to 2.476GHz)

Maximum Power of RF transmission: 20.2dBm (105mW)

Connectivity: Up to 4 receivers (Slave)

Input Impedance: 10K ohms audio (RCA) and 1K ohms (WIRE)

Maximum Level of audio input L/R (RCA): 2V RMS ( 8dBu)

Frequency Response: 10Hz to 22KHz (-1dB)

Total Harmonic Distortion (THD): 0.01% the 1KHz

Signal/Noise Ratio: >90dB

Crosstalk (separation between channels): >80dB

Power supply Voltage: 10 to 16V DC

Maximum Consumption: 160mA @12.6

Consumption in Stand-by: 10mA

Protection: resettable thermal fuse (PPTC), internal protection against polarity reversal

Dimensions (WxHxD): 3.47: x 1.18" x 4.65" 

Weight: 0.22lbs

 

CHARACTERISTICS OF RECEIVER (TW-slave):

Operational Range of Radio Frequency: 2.4GHz ISM band (2.404GHz to 2.476GHz)

Maximum Power of RF transmission: 20.2dBm (105mW)

Output Impedance: 470 ohms audio

Output level of audio L/R: 2V RMS

Frequency Response: 10Hz to 22KHz (-1dB)

Total Harmonic Distortion (THD): 0.01% the 1KHz

Signal/Noise Ratio: >90dB

Crosstalk (separation between channels): >80dB

Power supply Voltage: 10 to 16V DC

Nominal Consumption: 100mA @12.6

Consumption in Stand-by: 40mA

Protection: resettable thermal fuse (PPTC), internal protection against polarity reversal

Maximum Current output from remote: 250mA

Dimensions (WxHxD): 3.47" x 1.18" x 4.65" 

Weight: 0.22lbs

Price- $179 shipped PayPal-IntegrationPage-PaymentBTN-BuyNow

 

 

Additional Slave device-

Price- $94 shipped PayPal-IntegrationPage-PaymentBTN-BuyNow

 

Universal Antenna-

 

TFM1080i

The TFM 1080i Antenna has a universal application. It can be installed in any vehicle, secured by double-sided tape, developed with high performance, active circuitry that ensures clean reception, free of interference and noise. Great signal reception from AM and FM. Its design comes from meeting with the market trend, lightweight and discreet.

 

TFM 1080i antenna universal electronic windshield printed Rod 10.25"

SMD Technology amplified

8' 6" Cable from the antenna

Connector in brass surface treated to eliminate oxidation

Red LED

Connection PLUG DIN

Universal Application, can be installed in any vehicle

Price- $19 shipped PayPal-IntegrationPage-PaymentBTN-BuyNow

 

Voltmeters-

 

VTR-1200

Innovative Digital Voltmeter

Unique design, lightweight, transparent, functional and practical; very easy to be installed.

Displaying BLUE showing the mark of innovation that TARAMPS provides to its consumers.

For its connection, the connector system is detachable facilitating ease of installation.

 

Technical Data:

Voltage Range: 10.2 to 27V DC

Maximum Current output remote (OUT) 650mA

Maximum current Consumption: 60mA 

Dimensions: 4.72" X 3.47" X 1.18"

Weight: 0.22lbs

Price- $59 shipped PayPal-IntegrationPage-PaymentBTN-BuyNow

 

For RCA Cables and T-Line High Voltage amps(115v-390vDC), contact shizzzon@gmail.com for custom price quote.

Share this post


Link to post
Share on other sites

I know some guys in Indy that will be participating in this ;)

Share this post


Link to post
Share on other sites

May have to grab myself a HD8k if my budget allows :)

Share this post


Link to post
Share on other sites

I wouldn't hesitate. Finally got my other hd8k back from repair. Man these things put out hella power. I wish I could buy 2 more lol.

Share this post


Link to post
Share on other sites

the price on the HD8000 makes me sad I bought amps recently

Share this post


Link to post
Share on other sites

Hurry!

 

Group buy ends tonight! 

Share this post


Link to post
Share on other sites

It's over....now get me & the Indy guys our amps!! ;)

Edited by chicagofan

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

  • Recently Browsing   0 members

    No registered users viewing this page.

    1. Recent Topics

        • 17 comments
        • 178 views
        • 393 comments
        • 32,175 views
        • 2 comments
        • 670 views
        • 5 comments
        • 1,446 views
        • 6 comments
        • 1,015 views
        • 1 comment
        • 961 views
  • Similar Content

    • By Sencheezy
      My old build log was deleted when DSS lost their section. So I have to start from scratch. Here is the update for my truck for the 2015 season. This build will be complete by October 2015 and will consist of the following hardware.
       
      6 Team SSA 15" subwoofers
      3 Taramps HD30kSPL amplifiers
      3 JuiceBox LiFePo4 80ah batteries and 1 20ah.
      Single Reflex Bandpass Enclosure 10 cuft sealed, 35 cuft ported, 900cuin port area
       
      The end goal is to do a 165 any where. My last build loudest score was 162.3 outlaw with 6 15" DSS Ethos and 3 Taramps HD8000
       
      This is still my only vehicle that I own. 
       

    • By antoinez28
      My goals to be able to hit a 155.0
      With a window line box and being able to demo low note and burp high notes like in the 50s
      My build came a long way ...
      Working on getting that iPhone 6 slow mo cam is great
      https://m.youtube.com/watch?v=VOoaSMFNRbw
    • By sps1989
      My current setup consists of:
      -Advance auto parts group 34/78 up front
      -stinger spp1500d in the back
      -mechman 270a alt
      -Crescendo bc2k
      -Crescendo c1100.4
      -Knu konceptz 1/0 all around including big 3
      I was wanting to upgrade to something bigger (maybe a dc level 6 18). I am tore between 2 options...(both options will have c1100.4 and same batteries plus some later down the line)
      1st:
      -Taramps hd5000
      -2 positive runs of sky high 2/0 from front to back
      -3 positive runs to the amp
      -Big 3 in sky high 2/0
      2nd:
      -Another bc2k strapped to the other one
      -1 run of sky high 2/0 from front to back
      -2 runs of knu 1/0 or 1 run of sky high 2/0 to each bc
      -big 3 in sky high 2/0
      I can save money going with another bc, but would the more efficient taramps be a better option? Im just curious of yalls thoughts on the taramps.
    • By Sencheezy
      Ok guys, here is MY personal Review of the Taramp HD8000
       
      I personally own Three of them. I purchased two use from DangRebel here, and the third directly from Shizzzon. One of used ones from DangRebel went into protect immediately upon hooking up. And the BNIB from Shizzzon also went into protect while demoing Sunday afternoon while at Slamology. 
       
      Here is a few pictures of my installation for Reference. 
       
      On the chargers.
       

       

       

       
       

       

       
      So to explain my experience in total. My system consist of One DC Power 240XP, 100ft of 3/0, Ten Batteries. I also should mention I run each amp at 1.5 ohm, the amps are the Two ohm version.  Now, the drive down to Indiapolois is about 5 hours long. For the better half of the trip, I would turn the gain up half way, couldn't take much more than that, (pressure wise). So the most my voltage would drop would be .1-.3 Volts. During some testing at the shop, we clamped 3200 watts starting at 2.7 rising to 8.1 pulling a little over 300 amps of current. 
       
      The first time demoing there that Friday night, I was able to burn up 2 300 amp fuses while playing full tilt after 2 or 3 songs. Replaced the fuses, back up and running. 
      Saturday, I beat ALL DAY. Was still having engine issues. So for 87% of my demos were at battery voltage. Since the engine was off, that also means no rear A/C to cool them, still no issues. Yes, they did get warm. On sunday, got warm enough to not hold your hand longer than 30 seconds. But again, it wasn't THAT hot lol. 
       
      To describe how the amps are mounted. The rear wall is 3" thick of High Quality MDF. Which an another layer of 3/4" wood mounting plate is attached. Then the steel rack. Then the amps are mounted onto an 3/4" MDF mounting baffle, that is mounted onto the steel amp rack. Shizzzon informed me that there was still too much vibration, and wired too low, which is why the bottom amp failed. I was able to verify that the amps were indeed moving, but from what I could see, it was only becuase the truck itself was moving. Not much else I can do about that. 
       
      So in sum, these amps, in my opinion, are the better choice for us in every aspect, EXCEPT durability. If you think of where these amps come from and their origin, it makes sense for what I see is their biggest flaw. These amps are MUCH more sensitive than Koreans. The output section especially. We had I believe 3 other Team IAK members whom amps failed as well. One was becuase the wrong gauge was used for the speaker cable. One was for no reason, there's mine, and one other. 
       
      So, for advice for other users. It is ok to run these amps, they do power, cheap, small, and stupid efficient. To run these long term usage, have these key items.
       
      2-3 Group 31s PER HD8000. Use the appropriate size for the output section. 8 gauge min. Ensure there is NO to VERY min. vibration. And wire to the proper ohm load. I wouldn't even risk burping lower than rated. Do not count on box rise. 
       
      Please note, that the ENTIRE weekend I beat the living piss out of my system lol. Most people, demo for 20-30 seconds at most per demo. I would play full songs full tilt, had no issues. I played my system for at least 4-10 hours in total over the weekend. The amps gave me no issues until Sunday afternoon. Which was a much hotter day, maybe 5-10 degrees more. There was no smoke, just protect light. Yes there was troublshooting performed. Turn system off, let cool down, unplug everything, let cool down, remove RCA/Speaker cables, etc. 
       
      Moving forward, I will Continue to run these amps. At four ohms each for now, then at World finals run at 2 ohms. 
  • Recent YouTube Posts

×