Jump to content
Sign in to follow this  
KenC210

2013 Tundra Build (slow)

Recommended Posts

Now on to some updates. I started with the power wire that will be running towards the back. Two runs of of sky high 1/0 glad I was able to fit both runs along the side.

20140831_185719_zpsszsvv3or.jpg

20140831_185724_zpsarhpdxoi.jpg

 

 

The speaker wires from the door and dash wrapped up and will be routed.

20140831_123050_zpsjlgzvnno.jpg

 

Then to find a place for the front stage amp. Was hard to come up with a place but however under the front seat was best place, didn't really want to put anything under the seat but I had limited space. So I made a base out of 1/2in mdf so it would be secured.

20140831_180057_zpswmuv9h5t.jpg

20140831_180123_zps3zdtxmlp.jpg

A test fit to make sure it will be fine...

20140831_180142_zpsjz4sofpm.jpg

Good to go so I will be placing it there. Time to remove all seats again...

20140831_194825_zpsoqiqyjhu.jpg

 

Now to start with the Audio control LC7i to help me integrate the factory amp to the other amps. Of coarse with a good diagram I got from TundraTalk.net to help me out with which wires are what I was able to knock this out.

20140831_131159_zpsejvrchvg.jpg

20140901_182955_zpsw8n6ly6y.jpg

20140901_182939_zps8f2zu2gn.jpg

 

Now that I was able to get those wires done with the processor time to start cleaning up this mess of wires and start running them where they will go.

20140901_182901_zps6acigkil.jpg

 

Got my 12volt turn on relay in place to get the multiple accessories to turn one.

20140901_183023_zpsdzmnlien.jpg

 

Also got the Dakota digital  in place while i was running all the wires. The voltage will be read from the sub amp.

20140901_183044_zpstzhdtqbe.jpg

Share this post


Link to post
Share on other sites

Getting the box in for fitting. Also getting the holes drilled for T nuts.

20140907_180241_zpsccnazd97.jpg

20140913_173332_zpskzvazmp8.jpg

20140913_173321_zpsdpehpoeg.jpg

20140913_173356_zpschoghlzo.jpg

20140914_184244_zpsb2x7tbdb.jpg

 

After i got the subs mounted in place it was time for the amp.

20140915_144448_zpssqls7ris.jpg

20140915_144428_zpswzvnsakk.jpg

 

After the power, grounds set, and a double check for everything it was time to finish the rest off...

20140915_160505_zps5y3yoeuo.jpg

 

 

So I got everything playing and had a few issues. I had a tweeter not working which i found the problem which was where I soldered the wires together I guess I pulled the wire a bit to hard and it tore the wire, so I re solder and got it playing. The next big thing i have is with the aero ports are vibrating. I thought I had the in very secure when build the box but I guess not. I will have to try and fix this if I can't come to a decent idea to help prevent the rattle from the ports.

Share this post


Link to post
Share on other sites

Got around to setting up the gains so here is a test vid of the Hertz. I will be needing to fixing the subs box due to some issues with the port rattling so I have the subs at zero gain as of now till I get around to fixing the problem. I know the issue with the ports but I will need to cut out the front baffle and replace it as I will be securing the aero ports a bit better.

 

Share this post


Link to post
Share on other sites

any updates on this? As somebody with a crewmax getting ready to do some sub work, im very interested to see how the box fits with the seat in.

Share this post


Link to post
Share on other sites

any updates on this? As somebody with a crewmax getting ready to do some sub work, im very interested to see how the box fits with the seat in.

Yeah I have just been working on redoing the sub box since I messed up with the aero ports and didn't secure them properly. So I went and changed some specs to make it work as a slot port. The box ended up being slightly wider. Will be posting up some vids here shortly. I will also get a few pics of the box in with the seats up.

Share this post


Link to post
Share on other sites

Just a few pics of it all installed.

 

20141128_163134_zpsog8u8idt.jpg

20141128_163148_zpsuedhpa2g.jpg

20141128_163236_zpsrvpoduep.jpg

20141128_163244_zpsztxcmee3.jpg

20141128_163319_zpssicntrba.jpg

20141128_163335_zps5sedqsau.jpg

 

Just for the clearance for the passengers in the back

20141128_163356_zpsjyakahsa.jpg

Share this post


Link to post
Share on other sites

Just a bit of an update 12" bulletproof lift kit with icon coil overs sitting on 20x12.50 rockstar II rims with 38's toyo open country.

 

20150103_164711_zpswm4hggo9.jpg

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

×