Jump to content
Sign in to follow this  
dharris2488

New Member/The Woodlands, TX Introduction...

Recommended Posts

Sounds good.  I'd like to meet some new people, that actually know what they're doing... Should be a good show for me.

Share this post


Link to post
Share on other sites

There is a show on the 13th of July at DipTex. you can find info at Bassbattles and Soundoff.org for bass comps in the Houston and surrounding areas. I'm always down for a few beers!!

Tell Paul at DipTex I said hello. Those guys know how to get loud for sure.

Share this post


Link to post
Share on other sites

I think they might have the blazer running by that time. (12) ethos 15's on 40k

Share this post


Link to post
Share on other sites

 

There is a show on the 13th of July at DipTex. you can find info at Bassbattles and Soundoff.org for bass comps in the Houston and surrounding areas. I'm always down for a few beers!!

Tell Paul at DipTex I said hello. Those guys know how to get loud for sure.

 

Will do....

Share this post


Link to post
Share on other sites

I think they might have the blazer running by that time. (12) ethos 15's on 40k

Definitely checking that out... Hey Quentin, you offer recones for the Ethos right?  I think in maybe 6 months to a year, I will order D1 coils so I can wire to 1ohm.  Didn't want to do it right now, as my amps still have that new car smell to them :)   I know rise varies with every tone, but I think I'm  seeing close to 3.5ohms of rise on average.  I'm assuming it will probably be somewhat safe to wire the Q2200's at 1ohm strapped... I know you can't "tell" me to do it, but are the SoundQubed amps typically ok to wire to .5ohm single or 1ohm strapped?  This will be a daily driver as well...

Share this post


Link to post
Share on other sites

Well this sucks, my left front 6.5 Kappa just shorted out on me.  I took the speaker out of the door and water poured out of it.  Looks like I'm going to be looking for some front stage much sooner than I thought.  I need to find those dense foam acoustic rings that go around my speakers to protect them.  This really sucks!  I liked the Kappa's...  Oh well, time to move on to bigger an better, whatever that may be!

Share this post


Link to post
Share on other sites

The rise seen in most systems isn't caused by frequency or music played. Your typical dmm doesn't read quick enough. The rise seen is caused from heat. The dual twos have been shown on the Klippel to get over 6 ohms in series.

Share this post


Link to post
Share on other sites

The rise seen in most systems isn't caused by frequency or music played. Your typical dmm doesn't read quick enough. The rise seen is caused from heat. The dual twos have been shown on the Klippel to get over 6 ohms in series.

Oh ok... Well then, I guess I will rock what I have for now until it's time to recoil the subs.  I'm sure it will still be a marked improvement over my current setup.  I'm excited for them to get here, I'll tell you that...

Share this post


Link to post
Share on other sites

http://www.soundsolutionsaudio.com/forum/topic/61760-ethos-dual-12-enclosure-39w-x-16h-x-1975d/?view=getnewpost

Didn't look like you had an answer on the enclosure, not sure if it will fit in your car. It is the one Q designed for me on the same setup you are getting. Works beautifully.

Welcome to the site btw!!

Share this post


Link to post
Share on other sites

http://www.soundsolutionsaudio.com/forum/topic/61760-ethos-dual-12-enclosure-39w-x-16h-x-1975d/?view=getnewpost

Didn't look like you had an answer on the enclosure, not sure if it will fit in your car. It is the one Q designed for me on the same setup you are getting. Works beautifully.

Welcome to the site btw!!

Thank you for the enclosure design.  I do have one and I will post it in a second.  Basically, its 32.5hz, Vb=3  34.5W 16.5H 23.375D with 5 1/8" port width.  Leaves me 3.75 before displacement/bracing.  Let me see if I can post the pic.  I can't take credit for the box design, as Joe X over at SMD designed it for me.  I doubt it sounds bad, but you never know.  Joe X designs some decent enclosures and I haven't heard to many bad complaints, if any at all.  Now I have a proven back up... Thanks

 

By the way, this is for everyone, this site has been much friendlier and straight forward in regard to responses, over SMD.  Thanks for all the welcomes and valuable information everyone has shared with me so far. 

Share this post


Link to post
Share on other sites

Quentin, do you have any decals that I can buy to put on my enclosure?  I would like a big DSS or something like that so I can poly over it.  Let me know if you do please...

Share this post


Link to post
Share on other sites

How big would you like it? I can up to ~13 x 39 and still be proportionate. I have blue, white, black, silver, and red.

Send me an email or on so I don't forget

Edited by Quentin Jarrell

Share this post


Link to post
Share on other sites

How big would you like it? I can up to ~13 x 39 and still be proportionate. I have blue, white, black, silver, and red.

Send me an email or on so I don't forget

Thanks Q... Sending email now.

Share this post


Link to post
Share on other sites

Sweet and old school guy. I'm in the humble area if you need any help. I've built many systems and love doing it.

Share this post


Link to post
Share on other sites

Sweet and old school guy. I'm in the humble area if you need any help. I've built many systems and love doing it.

drailed77, what's up?  Sorry for just getting back with you, been on vacation.  Computer off, cell phone off, disconnected from the world.  Was quite nice!

 

Well, I'm having an issue with my enclosure.  The lows from 27hz to @35-37hz still sound sick!  Anything higher than that, and it's like i'm hearing a knocking sound in my enclosure.  It sounds like it's really coming mainly from the right subwoofer area, closest to the port.  Almost sounds like resonating of some kind.  It's making me sick... This enclosure was a BIOTCH getting in my car and now I also have it sealed off. 

 

What I would like to do, since it looks like I'm going to have to hack into my enclosure (and it won't ever be the same after that) is design it with a center round opening of some sort.  I think I can save some space and also get the end result I'm looking for.  Here's the question, I've always designed slots as my ports, using the enclosure of one of the port walls.  I've NEVER designed or built a round port.  I'm thinking with (2) 12" Ethos, I will need at least an 8" aero to make this happen  Is this correct?  Also, is it good to flare both the inside AND outside, or just the inside, or just the outside?  This is a daily driver application, sealed off, and probably no competitions.  I want it to sound good on music, but also get loud when I want it too.  So, a little mix of both... 

 

Where I get confused on designing this type of enclosure is, the part where it asks for Vb, do I put in net Vb or gross Vb, so it can determine the length of the tube to get to the desired tuning frequency?  This is where i'm confused... I'm sure this is a completely noob question, but this is where i'm stuck... Any help will always be appreciated!

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

×