Jump to content
meade916

2002 Caddy on bagz...8 Fi BTL 18's, 2 RF T15k amps (new vid pg 31)

Recommended Posts

DSC03145.jpg

DSC03148.jpg

I spent a ton of time on the wiring so i wanted to show it a little. There will be a plexi glass window in this spot on both sides. The 3sixty is barely in the window but at least i can see the light and tell what mode its in. I had no choice, the legnth of the RCA's and the fact its already done made it where i cant move it up more. Its fine it will be a suttle little view- thru anyway....

DSC03149.jpg

DSC03150.jpg

DSC03151.jpg

DSC03152.jpg

Ok time to deal with the PowerMaster charger. I wanted both windows to be in the same spot left to right........i didnt want a window down low on the left, and up top on the right so it was time to break out the butcher knife again. I had to peal the sticker off to gain access to the screws holding the circuit board to the case.

DSC03153.jpg

DSC03154.jpg

DSC03155.jpg

DSC03156.jpg

DSC03157.jpg

DSC03159.jpg

Share this post


Link to post
Share on other sites

Time to extend the wires......everything is soldered and heatshrunk. I extended the on/off switch wires to the front. I will probably drop a stinger volt meter where the power switch hole is. The digits fit perfect back there, too bad the one i have stopped working.

DSC03160.jpg

DSC03161.jpg

DSC03162.jpg

DSC03163.jpg

DSC03164.jpg

DSC03166.jpg

DSC03167.jpg

DSC03168.jpg

DSC03169.jpg

DSC03171.jpg

Had to make some brackets to hold the face to the wall. I had some Stainless layin around so i made up a few. They worked perfect.

DSC03173.jpg

DSC03175.jpg

DSC03179.jpg

DSC03183.jpg

DSC03185.jpg

DSC03184.jpg

the left side will match the right on the next set of updates. The window on the driver side will show the status of the charger along with a shot of the buss bars.......im clockin out for the night though, it was a long day.

Share this post


Link to post
Share on other sites

Steve that is nuts!

Share this post


Link to post
Share on other sites

thanks!

tinkered around a little this week. It was hard to work with the wind blowing so damn hard....it sucks almost as much as the rain or a 115 degree day. Just ruins any motivation.

heres a few pics of what i did though so far.

DSC03186.jpg

DSC03187.jpg

DSC03189.jpg

DSC03191.jpg

DSC03192.jpg

DSC03193.jpg

DSC03195.jpg

DSC03196.jpg

DSC03194.jpg

Share this post


Link to post
Share on other sites

if you look close you can see the plexi i put behind those window holes. Its just so i can see how it might look. Im going to remove it and after it gets wrapped up ill drop the real plexi piece in and perhaps back-light the stuff behind it......

DSC03266.jpg

DSC03269.jpg

DSC03276.jpg

DSC03275.jpg

DSC03278.jpg

DSC03281.jpg

DSC03283.jpg

Oh ya, something else i ordered up came on Friday :)

Im not puttin it in till last though i dont want to have to clean sawdust off brand new black carpet. Should match the seats and interior perfect.

DSC03289.jpg

DSC03290.jpg

DSC03294.jpg

Share this post


Link to post
Share on other sites

You did such an incredible job of routing all that wiring, that it is really sad covering it up. . .

Looks awesome man!!!!

Share this post


Link to post
Share on other sites

love ur work some nice chit u got there my fav one is my eye poped out lmfao

Share this post


Link to post
Share on other sites

wow it took me about 2 hours to go through the whole build.. Great job. Love the doors!

Share this post


Link to post
Share on other sites

thanks!!

sanded and sanded today...also started mounting the wood trim but i wont post pics of that till tomorrow....

DSC03337.jpg

DSC03338.jpg

DSC03339.jpg

DSC03340.jpg

DSC03341.jpg

DSC03354.jpg

DSC03355.jpg

DSC03356.jpg

DSC03357.jpg

DSC03358.jpg

also made a video tonite of the sister in law gettin served....http://www.youtube.com/watch?v=1lwxlaBARNE :D

Share this post


Link to post
Share on other sites

today i mounted the Neo-magnets so the panels could "snap" into place yet still come off if i need access...BTW, these RULE :)

DSC03359.jpg

DSC03361.jpg

DSC03363.jpg

DSC03366.jpg

DSC03365.jpg

DSC03367.jpg

DSC03368.jpg

DSC03369.jpg

DSC03370.jpg

DSC03371.jpg

DSC03374.jpg

DSC03381.jpg

Share this post


Link to post
Share on other sites

DSC03382.jpg

DSC03383.jpg

DSC03384.jpg

DSC03385.jpg

DSC03386.jpg

DSC03387.jpg

DSC03388.jpg

DSC03397.jpg

DSC03398.jpg

DSC03393.jpg

DSC03394.jpg

DSC03395.jpg

DSC03396.jpg

this will put the trim panels into better perspective.......at least how they are attached. Dont mind the pics in the beginning, that is just so it makes sense if some strange youtube viewer is wondering WTF im doing :)

Share this post


Link to post
Share on other sites

I have seen this on youtube before this system is so clean of a build. I love it when you played some michael jackson on youtube. Keep the great working going man....

Share this post


Link to post
Share on other sites

Nice idea on the magnets.

Share this post


Link to post
Share on other sites

sneak peak at the seats. Headrests are out for embroidery.......they are black with grey suede and are gonna say "T-30k" in black thread with rockfords font...pics when they come in.

DSC03406.jpg

DSC03408.jpg

DSC03409.jpg

Share this post


Link to post
Share on other sites

Can't wait to see these back in the truck all done up... Looking real good man...

Share this post


Link to post
Share on other sites

×