black_cirrus

If I Remember once I was told there were 8 major battery factorys in the us and they were run by 3 companys. The guy worked for exide but could have been blowing smoke. I have a exide orbital grp75 I think

I know how to edit the pic. but can't remember how to save a screen shot to edit it. it won't right click save as.

How did you do that I can't remember anymore tricks. to get the pic.

that sounds about right my mackie mixer board sub output says 75 -hertz down. The other boxes say 36-130 for the subs and 36-30,000 for the full ranges. So It may go all the way down.

There is one of those in my town, Black crew cab, I think it had tires over 50 inches, dually bed over single tires that must be 2 feet wide, air ports on both bumpers, giant hook on a winch behind the bumper, yellow engine, under the bed in the rear tire well is a crome piece of metal 12-16 inches tall so you dont see thru the frame and bed.. the driver was late 30's going to the gym. made the yellow f-350 crew cab long bed 0n 38's look kinda small. also there a couple times was a deisel jeep wrangler I think it was a 6.5 GM but not sure .

what about a 3.1 just install a center speaker for movies. but on second thought my screens will not be centered so that would sound wierd unless I put a small speaker above each screen. You guys are right this could be more trouble than I thought.

any suggestions on a dvd player that play dvd-a and pref. Sa-cd,s dvd movies also stand alone is okay. I think I will try to tune my system better before I do 5.1. but I do like the down mix idea.

for a front center speaker I could mold one in my dash or get a stand alone like this and putting in a rear center would be like putting in any rear speaker not factory. But all the alpine controls except the F1 is 5.1, Not sure on the F1 it may be 5.1 also. And dvd-audio sounds better. the imaging thing may be an item to detour me but I think I can work it out.

my idea was to take the surround processor. direct to the rear speakers, and center speakers(s). use the aux. in, on the deck to control the front components. my main problem is subs to the deck or Y'ed into the sub rcas.

Because I can and want to. Also 5.1 would be fine because to my observevation most dvds are 5.1 but speakers come in pairs and amps are 2-4 channels so 6.1 would be very little more work. 1 more speaker in rear deck and wire to amp.

I have really thinking about trying to run surround sound into my car but don't want to spend very much I want to keep my active 3way system I should be wiring this week, cross-overed in my deck I like my alpine 7998. What options do I have no cheap junk like pyle please

ghetto times only a few: Hard wired a deck used duck tape only on the connetions. Also used something to test wires but dont remember what now I was 400 miles from home and 15 min from town. at a friends place no tools stripped the wire with my leatherman I wired a door lock relay pair for keyless entry with 2 wire indoor extension cord. Now days I have spare wire and keep a roll of speaker wire on hand and buy elec tape by the ten pack But I have gotten pickier about how the work is done by my stupidist stunt ever thats another story. I still use my jump start pack to bench test stuff.

okay take the rem. off the amp turn on the deck and then press the rem. back on the amp if it does the amp doesn't like the rem. source. most decks delay the amp turn on to prevent pops other wise the pre outs are toast. how did you toast the int. amp

the amps maybe powering up before the deck starts. On my church's sound system if I turn on the second amp that feeds aux. speakers before the mixer board they pop. (the main amps are switched on with the board but the second amp is not used full time. so it is turned on seperate) I would try to power the amps up after the deck is on with a switch or some thing

Thank you for making it totaly clear.Thats what I thought but have never seen it laid out. FYI the 3way switch is a internal menu func. on my deck. now to find some good 4 cond. speaker wire and get it run. I already use the int. crossover but left the sub low pass on because I have it xovered lower from the deck doesn't sound any diff.