Updating some more orders now.

#8641 make the list?

Your's is at the top of the list of next to be shipped out.

What about Order #8675

A lot of Zcon's are in the works now, yours is in that batch.

Thanks

Updating some more orders now.

#8641 make the list?

Your's is at the top of the list of next to be shipped out.

What about Order #8675

Will start on beauty plate and amp rack until subs ship.

26" from the front baffle, so that is about 11.25" from the back wall. Now about 8" with the deflector in place.

 One coat then the lacquer

Wow, I could have waited then and build a smaller enclosure. Have to look more into them after I get my zcon's.

I would make it where the end of each side of the port is half the distance away from the "triangle as the port is wide. . If that's makes wines how I said it lol

I worry about building up turbulence by making it that close and wondering about displacement I will lose also. Have to draw it out and take a hard look at it.

28~29 Hz

Double post

Do anybody think I should make the back port divider longer or will this be OK ^.

That's real nice. How you doing the trim plate. I was thinking about starting off with fiberglass but might end up going with plywood.

Done some work on the Lanche after my dentist appt today. Went by the body shop and intalled the helper bags and 1" spring spacer. Then I got home and finished pre drilling and mock up on the box. them pulled it ll back apart. Ready to start gluing it together tomorrow.

Looking nice

Just made my 3 month mark, March 18 is when I placed my order. Can't wait to see how they sound in this box.

March 18th was 2 months ago lol

Yea 2 month's lol feel like 6 but still have little to finish up.

Trust me, I know. Im waiting on 6 zcons that i ordered on the 14th of March

Well I going shut up because they might be in same batch. Aaron stated that a lot are getting push out. I will finish up the box and door panels. That's will nice with 6 zcon's.

Just made my 3 month mark, March 18 is when I placed my order. Can't wait to see how they sound in this box.

March 18th was 2 months ago lol

Yea 2 month's lol feel like 6 but still have little to finish up.

Just made my 3 month mark, March 18 is when I placed my order. Can't wait to see how they sound in this box.

 

Don't know if I should put less angle on the triangle

Nevermind, I think this will be a better fit for me. (2/4 Kit For 99-06 GM Truck).

Thanks for the link, I was looking the (Belltech 2-3/4 00-06 Tahoe Yukon Escalade ETC lowering kit). I don't how bad the ride will be with 2" drop in the front.

 

 

 

Got fine thread kreg screws instead of coarse thread. I have exchange them so I can finish the back, top, corner bracing and parallel dowels. I see that a lot people orders being shipped out and hope I am in at least the next batch.

Looking good Lee, is the ride any different being lowered? I am also thinking about dipping my rims since they are old and seen salt water of Hawaii.

Thanks.

One baffle done

Looking good, get some bracing in there and she will be stout.

Going brace with 2" dowels and still have to cut and place corner braces. Still debating on running a full port divider down middle or a partial. Made the box a little bigger than design. 50" X 20" X 38".

Looks good man! I think you'll be happy with the birch decision.

I probably would try to avoid putting a brace in the port as it'll increase turbulence in there. Maybe just double up the side walls of the port and round over the ends.

I was worry about the rear of the port. Because they will firing into each other except in the center at rear where I will add a deflection (triangle). Double up on port walls, that will be with birch ply. Lol. I used a total of three sheets of BB for the box already.

Looking good, get some bracing in there and she will be stout.

Going brace with 2" dowels and still have to cut and place corner braces. Still debating on running a full port divider down middle or a partial. Made the box a little bigger than design. 50" X 20" X 38".

Well, I finally went out and brought the the Baltic Birch and it is about the same weight as mdf. It did cut light butter. Still have to go over the cuts with my flush trim bit and cut the holes out for the subs.