sxmdaniel
-
Content Count
9 -
Joined
-
Last visited
Posts posted by sxmdaniel
-
-
I also haven't measured to find out if my sub box will actually fit in my car. Or if I'll have enough airspace once it's built.
How does this sound...
32 x 12"Q's Powered off 3 x 100.2's
I have about 3 cubic feet to work with...will someone design me a box that SLAMS!!!
Fishercustoms.com , ask for Chris he'll set u up
0 -
I'm going to order four 10 " Q's to be mounted sealed each connected to it's own Alpine PDX 1.1000 , ( all 4 were benched at 1200 RMS ) , my question is BP power or no BP power , i have seen posts where they were said to perform wonderfully under 1000 watts , and many more that stated they could take more , so i'm confused as to if i should BP them or nt please answer , thank you
0 -
OOOPs , sorry guys , found my answer on a previous post asking same question under FI product category , thanks anyway .
0 -
Looked at the technical posts on SSD's did not find any explanation on this extr , what is BP power , what does it do ??
0 -
Also on the BL's, P chamfer is including in the cooling package. So no need to buy both!
Thank you , will keep you posted .
0 -
Newly converted to FIcarudio products by xconcepts from caraudio i am wondering what is the min power requirement for the SSD's i will be replacing a pair JL Audio 10w3v2's in a sealed enlosure of 0.625 which are both being powered by a JL Audio 500/1 , and being unfermiliar with the FIcarudio subs , i'm wondering will a pair of 10 "SSD's work properly being connected and boxed the same way ??
The Jl's were rated 300 W each , will the amp be sufficient for these two SSD's to perform properly ? i,m also thinking flat wind and copper , is it a good idea to add these two add ons with this amp and enclosure set up .?
Will also be adding a pair of 10 " 2 ohm BL's each connected individually to it's own Alpine PDX 1000.1 in a ported enclosure tuned at 32 , will add P chamfer , cooling , Flatwind , and universal , what do you guys think ??
Dan
0 -
Newly converted to FIcarudio products by xconcepts from caraudio i am wondering what is the min power requirement for the SSD's i will be replacing a pair JL Audio 10w3v2's in a sealed enlosure of 0.65 which are both being powered by a JL Audio 500/1 , and being unfermiliar with the FIcarudio subs , i'm wondering will a pair of 10 "SSD's work properly being connected and boxed the same way ??
The Jl's were rated 300 W each , will the amp be sufficient for these two SSD's to perform properly ?
Will also be adding a pair of 10 " 2 ohm BL's each connected individually to it's own Alpine PDX 1000.1 in a ported enclosure tuned at 32 , will add P chamfer , cooling , Flatwind , and universal , what do you guys think ??
Dan
0 -
Yup , another newbie here , i,m an active member of nissanmurano.org and i am getting ready to upgrade my system im my Mo , xconcepts forum member of Nissanmurano.org highly recommended FI and i'm ready to go , so here i am .
look forward to the FI experience .
Dan
0
BP power for Q's ??
in General Fi
Posted
I posted this question already in the technical category and only got an answer from JimJ ( thank you ) , and would appreciate more feedback so that i may place my order Asap , so i'm starting over in the general section hoping for more opinions , thank you .
I'm going to order four 10 " Q's to be mounted sealed each connected to it's own Alpine PDX 1.1000 , ( all 4 were benched at 1200 RMS ) , my question is BP power or no BP power , i have seen posts where they were said to perform wonderfully under 1000 watts , and many more that stated they could take more , so i'm confused as to if i should BP them or nt please answer , thank you
Dan