lincolntc
-
Content Count
24 -
Joined
-
Last visited
Posts posted by lincolntc
-
-
so i pulled my dp yesterday, and to my surprise when i set it on top of the box none of the screws or the driver pulled over to the motor. usually this happens, so i put a few on the side of the motor, and to my surprise they were very easy to pull off. this is unusual as it is a pita to do usually. any thoughts as to why this happened and wnat to do??
0 -
with no t/s parameters, is there any possibility of coming up w/ a design for either one? single dp 15 (d1.4), orion 2500d
0 -
just found my btl to be the same way last night, the magnet closest to the top plate split in half
0 -
i have, but i didnt look at it. looks like a bad deal
0 -
thanks you ia2 for the double answer
0 -
anyone know if the lethal injection 10 uses the same bolt pattern?
0 -
is there any 10" baskets that will bolt to a dp motor? are the holes in the way to drill it out to fit a 12 spoke or any other 10" basket? looking to turn a 15" dp into a 10" for an 03 deville rear deck ported thru the armrest install
0 -
top plate ID is 3.3793937
0 -
top plate ID is 3.3793937
0 -
gap measures .225 +/- .005
is that a tight enough spec.??
can i get a D2, ND??
0 -
i had a similar problem when i built the btl's first box, check to make sure the port is firmly secured to the top and bottom of the box. when i stuck my head in the port, i thought my sub was f@cked, but closer review showed that my port wall seperated from my top baffle. nothing a few screws and some titebond didnt fix:)
its worth a shot
0 -
bassahaulic it was a D1 before i took the cone off, and i will be measuring the gap at work today with a faro arm (3D mapping and precision measuring instrument)
its damned hard to measure a magnetic gap with metal calipers:D
0 -
is there a way to identify a D2 from a D1, other than measurements? which i can check:)
0 -
heres the link to the original sale, team psi at ca.com says it was a D1 motor
http://www.caraudio.com/forum/showthread.p...black+btl+18%22
is it possible ND to not have to send it in? and here are a few pics, maybe you can tell how old??
Pole +gap
motor
0 -
which of the old 3 slug options were cosidered basically universal, D1 or D2.i bought my btl from teampsi on ca.com, on his ad he said its a D1 so its basically universal. i have read else where that the D2 were the ones considered universal.
can anyone clear this up? im about to order a recone, and i want D2's but i want to make sure it will fit!
thanks fellas
0 -
if you weld the holes closed then redrill, they'll fit;)
0 -
thanks for clearing that up nick, gonna need a recone soon, do the new kits come w/ woven tinsels?
a broken tinsel is the reason i seen the offset
0 -
shes in storage for the winter
0 -
anyone else?
0 -
if you look close the pole channel is offset to the left of the outer channel almost the whole width of the channel.
0 -
look at the cooling channel around the one o'clock position, it isnt lined up but all the rest are!
is this normal? if not any performance issues from this??
thanks
0 -
i need 4 tinsel leads, one broke, i fixed it, then the other broke! im just going to replace all 4, do you still sell just the leads? if so how much and where to pay
for a loaded btl 18
thanks
0 -
how did you secure the 8g wire to the basket? i see it looks like it goes thru the terminal holes,but...
0
plans are screwed unless
in Incriminator Audio
Posted · Edited by lincolntc
so i planned on turning my smoked dp 15 into 10", only once i tore in to it i have an older 08 model with the ia basket holes only (2 sets- 12 and 15, 18 and 21) cant fit a 12 spoke or a aq,dd,ab basket
my question is, will the dr or li 10" baskets bolt up to a dp motor?