thanosdbfan

4 awg to 8 awg adaptors

Need an answer A.S.A.P....

Any news?

OK thanks for the clarification....I hope the order is not shipped yet... If it is not done can you update my order?

That's weird....I have spoken to several people in the web where they put Fi recones into MTs... Anyway i wil sent you an e-mail.Thanks!!!

Hmmm...So here is what i witnessed...One 12" sub triple stacked motor 0,7 ohm/VC coils connected in paralell configuration score 15_.4 db Second test one 12" sub quadral stacked motor same nominal impedance same configuration score 8 db lower.The only difference was the position of the coil.In the first case all the windings except the top five were into the magnet gap but in the second case all the windings were in the magnet gap. There was no difference in the length of the coil in both cases.So my thought was that it must have a sensitivity issue that caused such a huge difference.To be honest i expected the heavy loade motor to be louder... By the way, i recently (2,5 weeks ago) ordered 2 BTL recones for my 18" RE audio MTsDid you receive my order and payment via paypal?

Just wondering... Does the Hixm coil has better efficiency in comparison with the standard BTL coil?What are the pros and cons when using the first in SPL /power handling/output? Is there any signifficant difference in the subs sensitivity? A few days i have watched some tests on some new quad stacked motor subs and i wondered if it would make any difference if the coils were put a little higher than they originaly ought to be put (like 4-5 windings were out of the motor top instead of putting all the coil in the magnet gap)

They are killers...

So,is it out? I need one for my DE 3200s A.S.A.P.

I used to have similar problems with my old school TU 600... Try to do the next. 1.Check your amplifier ground wire connection.It is best to sand off the paint on the chassis ground connection spot. 2.Use a bigger ground wire 3.Try to use a single ground spot for every unit (one for each amp one for the proccessor etc) 4.Don't use a capacitor.Useless...(at least for USAMPS) If you see any improvement,check the power wire/wires. Last thing you should check is the RF (360.2) unit.There is a possibility that it my not be compatible with the input of USAMPS.I have witnessed this with my old symmetry EPX 2 (A lot of hiss and popping when i turned off the amps).Problem was solved with a new USX-3

whats the bix tuned to Typical PANDA/MARBELLA frequency 68Hz Fb is 55Hz

I guess i have to be patient. Anyway thanks!!!

OK

Ooops! My bad... Yes... I am talking about the standalone module...

For the AX line...

I was wondering if the MLT is available...

Bummer, well i learned a good expencive lesson on that one At least you have a limited edition amp.... we have a guy running one here daily with no problems, that little thing's a damn beast. I'm not going to say he beats on it constantly though. 2 guys here still use them in competition, in NSPL classes, because last year the fuse rating had to be 150 or less, and it has a 120 amp fuse rating. Guy with one of them hit 148.xx yesterday on 2 12's, and could have been a bit louder, but they couldn't get his cd player to quit skipping. During testing, the 4000x was .7 louder than a DD M3 He should try a cd changer or a different location for the source unit...

Bummer, well i learned a good expencive lesson on that one At least you have a limited edition amp....

The 4000X cannot play more than 5 minutes continiously... Don't use it for daily unless USAMPS experts say you can.When we bought them Jack Matheny specificaly noted that these amps were not for daily use... It was a little beast when it was first released...Regardless of its size it's very strong...I used 2 of them on 2 15'' MTs in a street C (160 lt net ported enclosure setup 3 years ago. Max score 152,6 dbs on a single Optima bluetop and only 1 0gauge power wire.on my Peugeot 106

Score is now 161.8 dbs certified and rising fast...

Made contact! Thank you!

Greg hasn't answered my e-mails...Need an answer fast!!!!Help!!!!

Compared to an AX 3200 DE which one would be the winner? I believe the new AX is capable of producing 240 Volt output...

them thangs are expensive $3500 i thought they quit mking the usa series but i guess not unless its a scam We have been using these things since 2003.Still running strong...Last certified score was 160.1 with 2 MTs 18"

OK... 2 MTs 18 DVC 0.9 OHM running by 2 USAMPS USA 6000.Each amp runs 1 sub @0.5 ohm nominal. on a wall . Street max setup (one ODYSSEY PC 2150 battery) 8 runs OO gauge wire on + and another 8 runs on -. Car SEAT MARBELLA Current certified score 160.1db @ 68 Hz...