UNIT 6639

Or you could order a sub and get one inside the box , I totaly screwed mine up trying to put it on the window

The BL was/is ported, so to will the SSD's be ported, they are going to go in the box I had built for the 2 BL's.

Hey guys, I am planning on trading my single BL 10" to a friend for 2 10" SSD's . I am trading because I just cant come up with the money for a new amp and another BL 10". So I figure, with my current amp (eD 9.1) I would be better off with 2 D1 SSD's. I have a custom built box for 2 10's , but never could come up with the monies to purchase the 2nd BL so the box is just sitting in my basement living room. I am thinking the SSD's would sound great off 1200 watts or 600 each. What I am hoping is that they will be louder than the single BL, I am assuming that with the extra cone area of the 2 that they will be louder off that alone. What do you guys think?

I have one, I like it alot! I have it listed for sale here but I am leaning towards keeping it. I know alot of peoples hat eD but the 9.1 is a solid amp in my opinion!

RE does not sell the 12.1 anymore, I am wondering if they can repair a damaged one. I have a friend who has one that needs minor repairs. Anybody know?

I think FI doesnt recommend BL's sealed, I think Q's and SSD's are their subs that you would want to go sealed with. Thats not to say a BL wont work sealed though, it would be a waste though IMHO

How much are they shipped to 26851? I want one for my old e12k. The old e cone has a little damage to it, running it inverted now. Also, where could I get the glue needed to put it on? Can I buy the glue from FI?

I understand that part, so what coil config will run an amp at .7? I know 2 D2 subs will net you a .5 ohm impeadence, but what VC config gets .7? What? quad coils or something?

I see alot of post where guys are running there amps at .7 ohms, how is this possible. I have run amps at 1 ohm or even .5, but how do you get .7??

When you remove your rear deck, please post how you did it, i cant begin to figure out how to get mine off!

I heard some rumblings about a new subwoofer company from a topic over on Sound Illusions forum, I clicked on a link that brought me over here to SSA. I joined just to be able to ask questions about FI products, next thing I knew, a BL was sitting on my door step!

I researched FI as deeply as I could on this forum before ordering a BL. After what I read here and talking to Scott,Nick and Shawn, I decided to send FI my money! Yea, the price of FI subs also influenced my decesion, but if I would have read bad things about FI, Iwouldnt have bought anything from FI. And some people wonder why people are going bonkers about FI right now, CUSTOMER SERVICE is why! You dont only get a GREAT sub at a more than fair price, but you get great customer service as well........ even if you dont buy something. I sweated Nick, Scott, and Shawn with my questions that I could have searched for, all 3 answered and thanked me for my interest! I really cant say enough good things about FI!!!

I have a BL 10" with the daily option, to me, it sounds great, it sounds just as good as my AA Avalanche did and my Ava sounded GREAT! I cant wait to get my second BL 10" so I can REALLY wang!

I know your busy Scott, but PM sent with my question? Arghh, your PM box is full , seems your popular around these parts

I know your busy Scott, but PM sent with my question?

Hey guys, I am having an issue with my amp I am wondering if my RCA's are bad, I had them loose in the trunk while my amp was uninstalled, could they have touched and burnt out or something, I didnt tape them off, only the power wire and ground, I didnt think they needed to be taped off as well. But my amp is sounding unright! the output is very low, I turned the gain up to max and it does not sound like a 1200 watt amp should sound, I dont know if that makes sense. I say that because I switched amps, from a eD 9.1 to a RE 12.1, nothing changed except the amp, all wiring is the same, the 9.1 was thumping, I know both amps are different but they are both supposed to put out 1200 rms so I am hoping its the RCA's. I am going to pull the HU when I get home and make sure both RCA's are in the HU, i may need to buy new ones to rule that out, is there a way to test them without special tools?

I have one and have some questions, wondering if you are familiar with them, I cant find much info on them on the net, google has faild me , anyway, if you do could you respond?

Well that didnt sound too inspiring , anyway, if all I can opt for is a drop in kit, thats fine! My e12k is in fine working order as it is, I just want a recone for it to "renew" it.

Vick, are you going to be able to get the full rms out of the 9.1 with your 18's? I forget what VC configuration you have on your 18's .

Scott, I forgot to ask, would I be limited to reconing it to only D4? I was hoping to get it reconed to D2 so it could pull the full power from my amp at 1 ohm. If not, D4 it is!

Thanks Scott, if you do find the items needed to recone my sub, could you pm me a shipped to 26851 quote for the kit? This sub is OLD!!! but still works, I was sitting on my basement couch looking at my BL 10" sitting next to the e12k and the thought hit me that they look similar, so then I thought hey maybe FI could sell me a recone kit for the e12k and I could have a new sub! Scott, guys, help me understand, if this sub or any sub has a certain size coil, for instance, this one has a 2.5, it cant be reconed to a bigger coil? So, I am limited to only reconing it to another 2.5" coil right, ok , if thats so, will I gain anything(sound/performance wise) by reconing it besides the new FI cone. It could use a new cone anyway because the dust cap was pushed in, it was repaired with but the cap has creases in it. Would I gain anything with the spiders Scott mentioned. And if it turns out Scott does not have coils for it, could I just pickup the cone and spiders from FI and just add those to the coils that came with the sub in its original configuration? Thanks Scott and NG for replying. Waiting on your reply Scott so I can send monies to you for the kit

I have an old e12k "blue e cone" DVC 2 ohm, I am hoping I can recone it, its still working and sounds good butI want to renew it I guess, I read somewhere that these were made by RE, so I was hoping I could get an FI recone kit and do it. If this is possible, what could I recone it to? Would the recone kit basicly change the sub into an FI like sub? Or would I need to have a new motor for that? Anybody have any info?

Low end is what I am looking for, I am not to concerned with tight bass, I have another sub and box that I can use for that if I want to switch up a little. I will try it out the way it is and decide from there, I will be sure to watch the gains, it will be getting 1200 rms from a 12.1, as soon as the amp gets here, supposed to be here on Wednesday

Thanks alot for replying man , I will see what I can find to shrink it down a little.

What kind of sound would I get if I dont bring it down to the proper size?