Big E

I agree. Remember...no replacement for displacement.

Do you have the electrical to back up 6K RMS? Looks like you're skimping out by buying a below-quality amp in the Crunch...I'm hoping you have a 300A/dual 300A alternators and at least 4 deep cycle batteries...

ICIX is probably the only place to find people that like eDuh anymore.

Who actually asks the one person that can give them a straight answer nowadays? Forums are the way to go!

Yeah, it'll have an 8 X 19 rear deck opening.....I guess I'd like to know if someone has used this design in a trunk car and did it perform better than a ported box??? How do you figure it's tuned to 35 hz?

Kicker K-series. Sweet! One problem though: the speakers are Polk MOMO's, not Pro 60's.

Mmmm flush mount Amp rack (need to clean up wires...possibly make a false floor to get them off the box)

That could be where I went wrong; I used the roll-on stuff.

That wasn't the point. I'm saying that if you call a company asking if you need a product they sell, and it is applicable, albeit unnecessary, they will still tell you that you need it. I'd like to see proof of premature failure due to a lack of isolators.

Well I got the box built, and I'm happy with it 3.7 ft^3 @ 30 hz. I used the dupli-color truck bed liner and I'm thoroughly disappointed. It didn't cover well at all...flat black paint would have been just as good. The Blazer is in the shop right now getting the doors fixed...I'll snap a few pics of the install and the box fully painted later on tonight or tomorrow.

Do me a favor and call Stinger and see if you need a capacitor

I almost feel bad for you.

Do we have to leave one feedback for each person? Or how is the drawing going to work? Are you going to put our name in a hat each time we get a referral, or each time we send a feedback?

7.1

If you're worried about cost, the SSD is a fine subwoofer.

Call the dealership and find out

Also don't forget, you'll need to buy an SD card with either camera you pick. I suggest either the SanDisk Ultra or Extreme...the size is up to you. The Ultra and Extreme have faster write times so they're good if you take a lot of action pictures.

Both are going to be very nice cameras. If you want to play with them in person, your local Circuit City should have both of them on display. I'd pick the Rebel XSi over the 40D just because I can't justify spending the extra money for the 40D.

Work on my Blazer pretty much stops until Thursday. I have to drop it off to have the door pins and bushings replaced...the doors sag pretty bad right now. There goes another $200

You play your sub up to 100 hz? Your crossover point should be right around 60 hz...

IMO the customer service of Sundown is bar-none the best I've ever dealt with for any company. SSA is a close second Honestly though, all three are going to do what you want them to do. I'm a Sundown fanboy now so I am a bit bias if it comes between those three. Then again...my cost on a zx1500.1 at Circuit City almost makes it worth going to the Kicker....

Did you try playing music without dropping the headliner first to see what it was like? I was hoping to avoid dropping the liner; I imagine it will be a pain. I've got the sun/moonroof and the overhead console so I don't know if it's going to be worth the extra effort. My 'peakers showed up today (Yes, I am going to be running them passive.) I've got the floor and the walls deadened and ensolite'd. I plan on having the door pins and bushings replaced before putting in the speakers as they have to take the doors off anyway. I'll be running RCAs and power wire tomorrow/Monday and most likely building the box Monday as well.

No pix but I got the front seating area fully deadened and I have both the walls deadened. I've still got over a full roll left, and I'm down to about 1/3 of a roll right now. It seems that I've only used ~40 sq.ft right now. I've got a full layer over half the floor and a full layer on each side of the wall. Does this seem normal or should I probably have another layer on the floors?

Alright, I snapped some pics of the ICON and the headunit. I haven't gotten too much in the way of progress of sound deadening as I'm caught at yet another snag. One of the torx bolts for the seat belt on the driver side was already stripped...and I found a LOC hanging off one of the rear speakers as well as the RCAs and a REM wire... ICON Alpine CDA-9811, currently in my beater while the ZR2 is sidelined And the problems/progress thus far: My buddy's bringing over a pair of huge vice grips which should be enough to get the torx bit out. If not, I'll drill it out and tap a new hole. I'll be working all through the night and morning trying to get this done before my dad gets back home from Ohio.

Sounds like one 12" ported should suit you nicely. You'll be able to keep quite a bit of room and it'll still shine in output (assuming correct box size). As for the spare problem...I hung it out back