shizzzon

Sounds good! SSA Forums- Bigrank916 - USB/LCDOther Forums - 0

Here is the official pricing YOU would have to pay if you did it yourself first. I like everybody to see this before you see the actual group buy pricing so you can what you are really saving. USB Bass meter- Cost - $270 Shipping - $55 Wire transfer fee - Typically $10-45 Total customer cost - $335-370 USB Bass meter PRO (2 meters side by side) Cost - $470 Shipping - $55 Wire transfer fee - Typically $10-45 Total customer cost - $535-570 USB with LCD Bass meter- Cost - $330 Shipping $55 Wire transfer fee - Typically $10-45 Total customer cost - $395-440 RTA meter- Cost - $250 Shipping - $55 Wire transfer fee - Typically $10-45 Total customer cost - $315-350 Now here is group buy pricing - USB Bass meter - (single meter) 5-9 Orders - $327 Shipped in the lower 48 states. 10-24 Orders - $300 Shipped in the lower 48 states. 25-45 Orders - $271 Shipped in the lower 48 states. Orders over 45, even more discount but more custom pricing. USB Bass meter PRO - (dual meters side by side) 5-9 Orders - $512 Shipped in the lower 48 states. 10-24 Orders - $465 Shipped in the lower 48 states. 25-45 Orders - $415 Shipped in the lower 48 states. Orders over 45, even more discount but more custom pricing. USB with LCD Bass meter - 5-9 Orders - $382 Shipped in the lower 48 states. 10-24 Orders - $350 Shipped in the lower 48 states. 25-45 Orders - $315 Shipped in the lower 48 states. Orders over 45, even more discount but more custom pricing. RTA meter - 5-9 Orders - $308 Shipped in the lower 48 states. 10-24 Orders - $282 Shipped in the lower 48 states. 25-45 Orders - $257 Shipped in the lower 48 states. Orders over 45, even more discount but more custom pricing. PLEASE REMEMBER - NOT EVERYBODY HAS TO ORDER 25 OF ONE THING TO GET THE 25-45 DISCOUNT! THIS IS BASED AS A WHOLE GROUP ORDER REGARDLESS OF WHICH METER U WANT. The exact pricing will be finalized once the group buy is over. Pricing should NOT increase, i'll make damn sure i'll keep this pricing set firm.

I'll be posting pricing in a few minutes. I would like to let people know this before just as a "Just in case this happens" from some new info i was just told by the company. This may not happen but if it does i want you all to be aware. If this does happen, which may not, it should only vary by a few bucks. They have informed me that since they do not keep a large inventory, it's quite possible that some requests may need to be build during the time the money is sent off. This is what this means- If all the orders are NOT the same... For example- 5 people want the usb bass meter and 5 people want the lcd meter and 5 people want the rta... If some of these items are not already made, they will have to go into quick production and make each thing separately that isn't already ready.... What this means is that it's "possible" that a slight increase in dealer cost would happen. I'm NOT SAYING it will.. so this is what's gonna happen to keep everybody informed- I'm gonna post pricing in just a few minutes. At the end of the group buy, i will send the requested list to them to give me a verified pricing list for everybody! Once this has happened, EVERYBODY will need to send me the money IN FULL at that time. There will be no partial payments, it will need to be in full. Once all the payments have been received(i'll give u all a little while), then the order will be sent off with a time frame if anything needs to be made. Again, even if the dealer cost goes up, if it's not by much, then i might not change these prices but everybody will be informed of the actual price once the group buy is over! The group buy is set to end 5-26-10. IF it starts to get slow before then, i may end it early. Again, give me a few minutes to post pricing.

WE HAVE PRICING PEOPLE. PRICING WILL BE POSTED EITHER TOMORROW OR THURSDAY. GROUP BUY WILL BE EXTENDED UNTIL 5-26-10

i am sorry, my mistake, you are right. The more espensive it is, the shorter the wait it is. I'm gonna tell you now... We are trying to work with the company to get to sell these things in the US with NO SHIPPING charges past onto customers. That's our 1st goal. 2nd goal... well we'll see.

the db dragers told me resin and sand would be the best option price-wise. They said using Polycarbonate sheeting may actually do better on the mic vs resining and sanding but at what cost does a 0.1db increase suffice if it even did? The view he looked at it was, the adhesive used to adhere glass to wood would be the problem compared to resin which would be part of the wood.

well, the connections will be as follows- Dual or Triple tinsel Leads. 99.99% pure Copper terminal adapter insert into speaker terminals(cylinder shape for maximum contact) A small copper bar attached in between the tinsel leads and the coil inside the sub for the highest current demand possible. Yes... these subs are being custom built.

I don't know if you know this but if your interface box ever gets damaged that comes with the Termlab, that's a $300 replacement! You can buy an entire SPL-Labs kit for that! For those wondering about the comparison between this meter and the termlab, well this is what i know- I own a termlab, a Hyperdynamics and soon an SPL-Labs meter. the SPL-Labs meter was precisely calibrated to match that of the termlab! For those who own a termlab meter know that not all tlab meters meter exactly the same. some are slightly loose and some are stiff. The SPL-Labs LCD meter has a calibrator on the device so if u want to calibrate your SPL-Labs meter precisely to the competition meter around town or your buddies meter, YOU CAN! How cool is that? These meters should never require a recalibration but just for fun, you have that option.

the Hyperdynamics meter is dead on with a termlab and it refreshes a LOT quicker than a tlab does too.. So i couldnt imagine this meter not being accurate. I would heavily suggest this SPL-Lab meter though for people who actually compete.

Lol, yea down to 9v.. there was something wrong there. Will i do agree with you mostly about your point of view, i would say that adding more wire when doing the big 3 will slightly increase efficiency. It lowers the resistance across anything that may have resistance. Also, it prevents wire from heating up due to excessive use which also causes resistance buildup. Of course the wiring is sufficient but it can always be better. Just like i can guarantee i could run a sundown 3000d off of 1 single 4awg wire 17ft long without failure. The wire would always be warm but probably not enough to melt. Adding more wire will decrease resistance to allow higher pressure = voltage potential, especially when things are under current demand.

hehe, it's a wall and the wire will be installed literally inside of the walls of the enclosure so the wire won't interfere with the air flow. So it has to run up the baffle, through the ceiling, down the back then out.

once u exceed the maximum current output capability of the alternator at any given rpm, the voltage will drop to the level of the batteries. That's just how it works. If your batteries are fully charged then it will drop to 13.0-13.2v. It is at this level where when left there under heavy load... any continual drop from here is just eating up those batteries.

Honestly, a single D3100 should handle 2 of those amps but it all depends on how much reserve u need. statistically speaking- the more reserve you need, the more ear plugs you will need

lol, i use a single d3100 and d5100 with stock alt on 21,000w of AQ amps for comp and demoing. So i'd say.... yea, lol.

contact phi on here. He has access to them. See if his distributor still has some in stock.

I expect to hear an extensive review of this meter when u get it too!

cant do snatch and grabs with bulletproof laminate sheeting

for the money, i'd just stick with what u have and if u need any more dekas, buy 1-2 more. If you close to KY, i can hook u up with some dekas for around $100 or a little more brand new, the 9a31s, but it's gotta be local pickup only. We do LOTS of group buys on these batts about every month or so.

caraudiodeals

talk to me about security, i'll give u the info u need to know. I'll warn u now, security isnt cheap. I spent about $1,400 on my car.

if anyone else wants a deal, hop on over to the Group buy thread and put your name down in the FS section.

i dont care if he adds 5,000 runs of 1/0 cable. For him to drop to 13v flat means his alternator is maxed out at the rpm he is at. You can't maintain 14v or higher with a stock alt and a bunch of batteries and wire unless you use a fluxcap which is NOT what i am recommending either. You simply need a high output alt to maintain that voltage level.

SSA and anybody affiliated with SSA is not associated with this Group Buy. Please do not request information about this thread to SSA as they are not selling this product. Thank You! This Group Buy is specifically between me(ShiZZZoN) and with the company who manufacturers this product. All of the following products are available for group buy- USB Meter LCD Meter USB Pro Meter Wireless Bluetooth Meter USB Noise Meter RTA Pro Meter For information about the products, please visit the website- SPL-Lab USA This will be a very large group buy but there is still something else.. The Customer, you, will be able to choose their own measurement range! This means you can choose a device taylored specifically to your needs. Below, I will list ALL available options for each meter that customer may choose. No matter what options you may choose, the price will still be the same! USB Meter- Stock specs - 120-179dB 20hz-120hz Price - $349 Group buy Options- 10-120hz110-169dB, 115-174dB, 125-184dB, 130-189dB, 135-194dBLCD Meter- Stock specs - 120-180dB 20hz-120hz Price - $399 Group Buy Options- 10-120hz115-175dB, 125-185dB, 130-190dB, 135-195dBUSB Pro Meter- Stock specs - 120-179dB 20hz-120hz Price - $499 Group Buy Options- 10-120hz110-169dB, 115-174dB, 125-184dB, 130-189dB, 135-194dBWireless Bluetooth Meter- Stock specs - 130-180dB 20hz-120hz Price - $419 standard, $449 with extra long range Group Buy Options- 10-120hz125-175dB, 135-185dB, 140-190dB, 145-195dBUSB Noise Meter- Stock specs - 80-140dB 20hz-20000hz RTA Pro Meter- Stock specs - 90-130dB 20hz-20000hz Both of the above meter can be changed to 10hz-20000hz. For custom calibration, please PM me for more information. All group buy payments are sent to- [email protected] If you are wanting to change anything listed above from stock specs, please put in payment or PM what you would like your specs to be. Thank You. Payment information- We request minimum deposit of $165 during group buy to be guaranteed group buy price. You can also send full amount as well. If you do not send full amount, we cannot release product for shipping until it has been fully paid. Expected delivery of inventory for this group buy is sometime near end of February 2012.

It is 2 1500s strapped internally. The speaker terminals have dual + and - connections. These are NOT paralleled inside like many new amps are today. They work independently from each other. The amp is rated as follows- 1500wx2 @1ohm 2000wx1 BRIDGED @4ohm 3000wx1 BRIDGED @2ohm

when we first started playin with the APs, everybody was still leary about them... Several months later, me and others started pushin people to use them because of their reliability and performance. There are MANY people in my area right now running these AP amps and nobody has issues with them. Just because they are a mainstream company doesn't mean they are crap because they are so cheap. I bet you didn't know the MAP pricing of an AP30001D is over $600 did you? Just because people can get them half off at other places doesn't make them cheap. The companies that sell them for just over $300 is cheaper than dealer pricing. I know this because our local dealer told us this and doesn't think it's fair, lol.