Quentin Jarrell

Yea they disappeared. I will have the 15 back up and I finally have 12 results as well.

Yes the Ethos 15 uses 3 stuff and one soft spider.

Waiting on sample for it. The initial Primo driver is being assembled now.

X

The spiders are stackable as the Ethos uses four however being a true progressive spider they have a conture that keeps them from sandwiching without effort. It takes a bit of compression to get them sandwiched tightly The baskets are prepped. They aren't ground down to the bare metal just as the top coat isn't ground down to the steel in a car to make it hold. It's just not needed. And if any glue joint did cone unglued it would be covered under the 3 year warranty.

uploaded just for Sean........................

Depending on how slow this front moves through we may get 6 inches or so that'll stick.

The DSS adds about 25 deebeezz but yea I have/ can have others.

Ethos coil pricing added to top

Give me till tomorrow and I'll PM a total with shipping. Do you mind if I roll it up to fit in the smallest USPS box as possible to save shipping? If you are happy with pricing I'll send over a paypal invoice.

Sean I just might need to borrow a sled for tomorrow

This cold front coming through is starting another migraine. And I'm plum out of imatrex.

Honestly not sure. I've never had a TI basket in my hands. The 18 gaskets fit the 6 spoke 18'' frames.

Which Protank? 1, 2, or 3? I have a 2 and 3 and like the 2 better. I was frying coils in my PT3 every 2 days or so. But the PT2 is solid. Very nice. Not trying to bury your thunder... But I have amazing vape mail coming tomorrow. I am super stoked. I have a Nemesis arriving, an Aqua Atomizer, a Kayfun clone which is similar to my Russian, and a few batteries. The Nemesis is a HUGE deal. They build them only 2 or 3 times a year and if you are lucky, you can snag one within a few hour window. There are currently (after this run) less than 1000 built in total, not just this run. It's a big deal. That's what you get for running Korean. If it was Chinese built you wouldn't fry ur coils. Smokin all that dirty power is bad for you.

While I work on my store, below are some parts I have to offer with pricing. Orders of $75 or more will receive FREE SHIPPING. Orders less than $75 will be quoted on a per order basis. ALL orders except orders containing cones will ship USPS. Gaskets will be folded to fit in flat rate shipping unless otherwise asked not to. GLUE KITS tba 12 SPOKE BASKETS 12 inch $26.8 15 inch $31.40 ALLEN HEAD MOTOR BOLTS 10mm long $.42 25mm long $.50 8 INCH PROGRESSIVE SPIDERS soft $4.5 medium $4.5 stiff $4.5 stiff w/ 100 amp leads $18 stiff w/ dual leads $tba TERMINALS 8 gauge spring terminals $3.5 CONES 10 inch $15 12 inch $17 15 inch $21 18 inch $32 GASKETS 10 inch $6.5 12 inch $7 15 inch $8.5 18 inch $11 CA GLUE $tba accelerator $tba rubber glue $tba flux $tba solder $tba DUST CAPS 6 inch poly DSS logo caps $2.30 3 INCH COILS "Ethos coils" dual one or dual two ohm four layer flat wind aluminum on aluminum former $30 former height 115mm winding width 70mm ID 76.657mm (recommend a 75mm or smaller pole) OD 82mm (recommend a 85mm or larger plate ID)

Have a few brand new ones laying around. If you don't mind them folded I can ship the two for $30.68. They will be shipped in a medium flat rate USPS box.

They are about 63 pounds. I just call it 65 pounds for the 15 and 60 pounds for the 12 Not the worst glue job I've seen Jon.

.

pics of your mad glue skills? lol

Q is on the high side for sealed. It'll work but with smallish sealed boxes system q will be up around .8 to 1

Yea. I was bleeding the breaks without the caliper on the rotor. I had to completely remove the rotor from the line to recompress it to get it back on. Even with the line off it was a bitch to compress.

I have another charged motor coming soon. Just for you I'll build one up.

did the same exact thing to my civic a few months a go. had to release the e brake let pressure off the lines and re blead the break lines. fter purring the capipers back on of course

get in it

My build house has finally went through my pile of stuff and found my "Primo" motor . This sample will be made into a 12 however will be the first driver available in a 10. The Ethos has just way too much balls to be made into a ten. I might have initial testing results on it in a week or two...maybe.