Quentin Jarrell

Louisiana is a pretty pimpin place. alcahol is for sale 24 7 at your local gas station a nd walmart. Just al long you dont mind a few rednecks and coon asses

got a ton...literally a ton... of grin in 2.5 pound grain bags i gotta unload out my truck

Yep they use a cotton lining between the copper and jacket. Remember. Welders are using this stuff to weld over several hundred feet. It needs something to help flex at that length.

oh, they'll fit. I got a reciprocating saw that says they will

that would be the cheapest option unles you sold your current sub

Below is 2/0 EB Flex. The discoloration is mold. It has been sitting under a covered car port for about 6 months.

I've used welding supply and the EB stuff. Yes the EB has less strand cound but both contain he same surface area therefore both within spec standards. The EB flex however is a good bit cheaper. I have found that the EB wire does not have any micro ban additive in the rubber to keep mold from growing on the jacket if that would be a problem

.

that's not plasti dip. Look heat gun, squeegees, and extra vinyl on the floor

Save time and money and but the EB flex

It's at Pat's office right now. I already know what the parameters will be as I already had samples tested a year ago. I'm just really anal and like to triple check my work. The box will be small. For a bandpass you can expect an s factor of .7 with a total volume of around 2.5 cft. Going down to 1.5 cft will get you in the realm of a .5 s factor. Pass band will be ~30-75 hz while keeping ripple under 3 db

Satin blue or silver. Or rust oleum hammer finish

The way I see it is these guys spend their hard earned money and more importantly their time on my product I need to try as hard as possible to ensure they know they are supported and appreciated. One of my most important goals is to cater to the needs of people who sometimes without even thinking about it has the biggest impact on sales for my company. As long as my budget allows and it is not against any comp rules I'll be here to help.

.

You telling me my backs been hurting for two days now. On a side note. I'm gonna start slicing on a burp box tonight

If they were smart they would have set up a camera and fined their ass for stealing federal property

Simpson has a few nice ones as well. Y'all look around the interweb and see what you like.

I want something that screams "that dude competes for DSS". Not that's a cool shirt where did you buy it.

Not sure. I want something extremely nice and professional. Not some cheap dickies button up shirt.

The sub would go in the floor but I have ok fiberglass skills. You'd only lose 3 or so inches of depth in the trunk.

I think that applies to anything you like doing that you turn into a career. I know I could care less if I evere install another head unit again.

I will be giving shirts to competitors that will be running DSS product. Since y'all will be wearing them I want to make sure y'all approve. I know some of y'all are pretty big guys, will 4x suffice? I am thinking something along the lines of the below pic. The red would be blue, DSS logo will be on the back and front pocket and if you like your name would be embroidered on the front.

Thanks for the welcome! I've been working and spending time with the lady, but I had some time. I did the best I could to get dimensions, and I even snapped a couple pics. Before we get started, let me show you guys what i'm working with here. So, from how I measured, I want to play it on the semi safe side to make sure it gets in, and to have a tiny bit of trunk space left over. Really though I just don't want have a box that's too big to fit so I played it pretty safe on the numbers. Here's what I got. Entry size 35" inside trunk: 17" deep 38.5" wide from wheel hub to wheel hub (i'd have to remove that stock pitiful sub) 12.5" height Those are my numbers I got. Again, they're a little safe, but I just wouldn't want a box too big to fit. So there's a couple inches give i'd say in a few directions. Now then, back to some questions. I have no idea, when I get the sub, since i'm going single setup biggest sub I can fit, what ohm should I get the XCON? I know nothing of wiring. Also! There may be a spot for the batteries. Under that trunk there's a wheel well with a full size spare tire. Surely I could fit batteries where a full size tire fits. Also, i'm not sure how much an alternator runs, but i'm sure I could work it into my budget. I ave to make sure that wouldn't void my warranty or anything just h. I remember I went to one shop and he was trying to sell me a HO alternator pushing about 216 amps for about $1 an amp I think. It was a year ago though so it's hazy, but i'm sure I could work it into my budget. Just gotta make sure I won't' void anything. Any help is appreciated here to decide which size sub best will fit my needs. I'm really open to suggestions. I trying to be as optimal as possible with what space I have. Perhaps i'll get another battery while i'm at it and throw it in the spare tire well and throw out the tire. I honestly hadn't considered an extra battery. Sounds like a good idea though. I'd really appreciate a designed box if you can take the time to do that for me. That'd be amazing. All I can think of of what i'd want from the box is for it to pound out lows and be loud so I can feel the bass (along with others around me ). So I know ported, and tuned around 32. I honestly don't know how low you can go and be advised to tune that low, but I figure 32 is good. Thanks for the welcome! Don't worry about voiding warrany. It is federal law that the repair shop has to prove the aftermarket has caused damaged to the vehilv causing a voide i nwarranty

I am very very very very very glad they decided to not make it look like a stock vette. It'll gonna tear the new viper a nes arseho without a doubt. especially with the PS2's. And I am a die hard viper fan. I'd still get a gen 4 acr and throw on a twin turbo and spank that ass on the track

I come from 12 years of gifted visual arts so I realy appreciate the artwork. I just not fond of the canvas. However no one can argue with are intellect and skill it takes to create artwork like that. I fully admire it strickly as are I just don't prefer the canvas. I much more enjoy it framed in a venue.