wrathdchild281

Hey guys im about to order dual alts for a 03 tahoe. Do i need any extra pullies and also is the belt included? Im gettin it from Dom at Iraggi and hes not replying to well to emails. thanks

I understand now...so what would you guys recommend in my case as far as how many alts and what size?

well if im demoing my system or whatever and have my rpms up will this voltage stay the same? With the setup i have would you go with like 3 220 amp alts which is a total of 520amps at idle or would you go with like 3 300 amp alternators and have more amps at peak and only 390 amps at idle. Im set on the amount of batteries im gonna run for this setup and its gonna be a total either 5 G3100 batts or 5 kinetik 2400's. So with those batts and my daily setup what would you do as far as the alts go?

so if i give them atleast 880 amps from my alts why wont it the voltage stay high at full tilt? The batteries will only keep them from staying over like 12.7 volts or whatever right?

so if i get say 3 300amp alts does that mean if im demoing the car and have the rpms up then i wont have any drops in voltage? I would be sufficiently supplying all of my amps with more than enough amps then they are drawing total.

I tried to look up past forums on this and had no luck. How much will a zx2500 draw at 2 ohms? Im gonna run 4 for a daily setup and im trying to figure out how many alts and what amperage alts i should run to properly supply these amps with enough amperage. thanks

nice man looks real good. Hows it sound? The kicker 2500s and the btls are nice matches. i had the same setup in my dakota but 2 and 2

haha you are! let me know when it blows your socks off.

4 18's walled bro. I had 2 18' btls in my dakota truck walled and it was loud! Im now buying a silverado and getting the crew cab just so i can run 4 18 btls walled for a daily setup. I say go for the 18's and like BKO said just get a back up camera if you think its necessary. Also the btls sound fine to me daily but i guess everyone has there own opinion.

you need to change that avator pic bro..talk about a serious distraction. Im gonna email dom and try and find out.

well the 240 would be to help out the at idle amperage because i will be using it for daily so high rpms isnt always possible. Also why would you pick the 3 300s over the 2 350's and 240? The 2 350s and 1 240 will actually have 40 more amps total at higher rpm.

Hey guys im about to purchace a triple alt set up from iraggi alts for my silverado. My question is should i get 2 350 amp alts and a 240 amp alt to help with at idle amperage or should i just get 3 300 amp alts. Ill be running 12k rms for a daily setup, thanks.

lol BKO.... Soundmekanic what is your spending budget?

They look real good let us know how they sound in your truck.

looks pretty legit to me. I say go for it and let us know how it all works out for ya.

As big as you can go man. Go with either excessive amperage, iraggi or ohio.

deffinitely a fully loaded btl, and ya make sure your careful setting it up.

Real nice score man, I bet it moves some serious air.

Nice work man. After you get that first one out of the way your good to go.

No when i turn the car off it immediately drops back to 8 something volts. You would think driving it around would help charge it but no luck.

Hey guys im in the process of taking out my system in my truck. Well i took out the three batteries and all my amps and subs i have in my cab and when i went to start the car it wouldnt turn on. My volt meter was reading like 8. something volts and to turn it on i have to have it jumped. Any suggestions on what it could be. My fuses by the battery under the hood looked fine. The alt is fine as well it idles at like 13.7 volts. thanks.

Hey guys im looking to try out the maxx link but i have a question for ya. Im gonna be running 4 kicker zx2500.1 amps and 2 18in Btl dual 1 ohm subs. The zx amps are 2 ohm stable and i was wondering if there is any possible configuration to have the amps see a 2ohm load once strapped. Also would i be better without the maxx link and running each amp to each coil? What ohm loads could i see there. thanks

Hey guys im looking to try out the maxx link but i have a question for ya. Im gonna be running 4 kicker zx2500.1 amps and 2 18in Btl dual 1 ohm subs. The zx amps are 2 ohm stable and i was wondering if there is any possible configuration to have the amps see a 2ohm load once strapped. Also would i be better without the maxx link and running each amp to each coil? What ohm loads could i see there. thanks

So each amp will see a 1 ohm load. Do you all think i can run the zx daily at 1 ohm? Should i run into any problems? also what about using that maxx-link.

Im running 2 zx2500.1's and a kx650.4. Ill email nate and also run some more run to the batteries in the back like you said.