Jwills

Thanks for the advise... i have a 2010 mazda 3 so my seats fold down in to different sections.

Not really a fan of port back sub back for me. This is a link to to a couple boxes accomplishing what I am trying to do minus the center port... maybe it will help explain what im tryna say http://www.caraudio.com/forum/enclosure-design-construction-help/411222-trunk-wall.html#post6244757

I'm currently thinking about building a box for a 12 btl with both the sub and the port aimed into the cabin, sealing off the trunk from the cabin. I have looked at tons of boxes doing this but they all port on either the right or left side of the box. I often have 4 people in my car so this would mean the seats would have to remain up giving the port very little room to breath. My middle seat has an arm rest that comes down and my idea was to have the box port right there so that i can just put the arm rest down and give the port a place to breath. My question is can i port the box in the middle and place the sub to either the right or left of the port. I don't have a in-depth understanding how pressure works inside a box but I'm now trying to do something that would kill db. Hopefully you can understand what im trying to explain but thanks for any help that u can provide.

I wish i could sit in that car when its all finished...

Def looks good... can't wait to see better quality pics

Hey if you find away to get them let me know because I was looking for some bigger FI stickers as well

This is my current box plans for the 1 18"BTL and 1 Saz-3000d I have. I plan on putting all these into a 03 Tiburon(hatch) and competing in spl. Really my only question is would a bigger box better/ is 5.27 cubic feet enough. Thanks box: (outer dimensions) heighth = 16.5 width = 36 depth = 21.5 port: (inner dimensions) heighth = 5 width = 7 length = 10 this port will tune the box to about 34.67 hz which is what i personally like to tune mine to. after port displacement...this will give you about 5.27 cubes of air. so you have room to brace it and not go below the recommended volume. this is also assuming that you're using 3/4 MDF. competition port: (inner dimensions) heighth = 5 width = 9 length = 5 this port will tune the box to about 46.21 hz for comps. you can add to the width if you wanna tune higher, or take away to tune a little lower. after port displacement...this will give you about 5.39 cubes of air

Thanks alot! Now I have run into the problem that i need a box. The dimensions my trunk(hatch so I'm not sure if i measured it right) are W 33in, L 36in, H 16in. Also what should I tune by box at. I know I'm going to have to keep testing and rebuilding.

OK, I'm going to buy 1 18" BTL today and I need to know what options to go with. I want to compete in SPL but I do sometimes want to be able to listen to music. I'm running it with a SAZ-3000 and I don't ever plan on adding another Sub. (I could never fit another) Yup so what options should i get?? thanks

So i guess i don't have the money to go with my original plan and get 2 12s each with a SAZ-3000 on them so i have a new plan. I wanna compete in SPL and occasionally be able to listen to music and i drive a 03 Tiburon GT. How would 1 18" BTL (fully loaded) with one SAZ-3000 do? (i do have the electrical system to run it) Also if i do this what should my box be? Thanks

Hey I own a 03 Tiburon GT and am planing on putting in 2 12" BLTs with 2 SAZ-3000ds. I want to compete in SPL but also want to be able to listen to music (not as important). What type of box should i get ported or seal and should I get a wall or will it just be a waste of wood. I don't want to do a wall unless it will boost me db. Thanks for the help, I don't have a clue what to do.

Well.. I have taken your guys advice and I'm going to go with 2 12" BTLs and 2 SAZ-3000d. Hope this will do as well as everyone here says

I was just wondering if anyone knew of any good car audio shops in Ohio (Columbus would be best) that have worked with Fi audio before and could do a custom wall for 2 12" BTLs and probably 2 TD20001 r/f amps. I like competing in meca's car shows (SPL) and i don't think i should do the box like originally was going to. Thanks

I was just wondering if anyone knew of any good car audio shops in Ohio (Columbus would be best) that have worked with Fi audio before and could do a custom wall for 2 12" BTLs and probably 2 TD20001 r/f amps. I like competing in meca's car shows (SPL) and i don't think i should do the box like originally was going to. Thanks

Also a friend recently told me to go with a Hifonics XXV Cyclops again i would love to know peoples opinion. I would have near known that the other amp wasn't a good idea with out this forum. Thanks

Ya i kinda wanna stay with the BTLs but idk... ill see if i can get the money together to buy 2 12" BTLs and 2 sundown 3000d but if anyone one knows of any less expensive amps that can get the job done tell me but ill shoot for the 2 sundown ones! Thanks alot

I'm now looking at 2 Hifonics Bxi2607 2600W amps.... one per BTL. Will that be enough. I would go with 2 Sundown 3000D but i simply don't have the money to get them now

Hey i just wanted to know what would be a good enclosure for SPL with 2 12" BTLs.... I Drive a 2003 Tiburon GT and do wanna be able to listen to music occasionally. Thanks for the help

Ya i know i need a better alternator and I already have 2 good batteries from my last install (3 15" L7s got stolen from my truck).... and ya I do plan on sometimes listening to music but i really only care about SPL right now... Yes want to Compete with this car

Hey I'm currently thinking about buying 2 12" BTLs for SPL.... I drive a 2003 Tiburon GT and planning to put them in a full wall. Could someone give me some ideas about amps, what options to get with the subs, how much RMS do i need/can they handle, and If this is really the subs I should get? Thanks