rmzsuzuki89

Other side. Screws are a lil long for the job, but they do get the job done. Kinda looks cool too, even though all of this will be paneled off. I came back into the garage to this.

Some good progress today. Decided to practice using cardboard for a stencil since I will have to for the beauty panels. Another side up. First 2x10 test fit.

It's really thick. That's kinda what i figured as well, but thought that I should probably get a second opinion.

Gonna be fun straightening all of this out haha. Where it is until tomorrow. I'm surprised that I got any work done today. I've been going since Friday evening haha. And there was a 3 story water slide at the place we stayed on the beach, and I somehow managed to land on my head, then my hip started to slip again haha...But I felt like getting at least a lil done. And a quick question. Does anyone know if the fiberglass that is used to make boat hulls would work for the inside of a box? I have access to about 1,000lbs of the mat, so all I would need would be resin. I figure since I can get it I may as well use it if it would work well.

Got back from the beach around 1 today and decided to do a lil work before everyone that was at the resort with us got back to the house. One side on the back part about to go in. Getting ready to start the shell that will be around the back part. It will be a combo of 2x10's, 2x4's, and 2x2's. So this will make the walls of the back part go as follows: one layer of 3/4" mdf, two layers of 2x10's/2x4's/2x2's, another layer of 3/4"mdf, and possibly some fiberglass.

Thanks

More of my "clamps" haha. There's also 2x4 chunks wedged between the back wall and the battery rack. Little slot for my other grounds. Some fuel. Between the bungie cords and back porch table to hold the wood for the table saw, I was able to get a lot done by myself, and occasional help from my dad...I was gonna quarter in to the back from the floor, but the angle would have be so shallow that I wouldn't be able to drill. I'm going to the beach until Sunday with my parents. So I may or may not get more done today, but there will be more updates early next week at the latest.

Updates! Got a lil more work done today. It's not much, but progress none the less. Our little setup for the table saw haha. Test fit of outer back wall. All glued. Who needs clamps and screws haha.

Thanks Thanks Hopefully I'll get some done tomorrow. We'll see how fast I can get the trailer waxed lol.

Haha Idk who would have a use for it, not too many people around here with 21"s and a full sized suv and willing to give up the 3rd row and all of the cargo area lol. Although some lady that my dad say at the dump took my old wall box to use for her cats lol.

The clean up. The can got pretty damn full.

Well, finally got to HD today around five and picked up 4 more sheets of mdf, a 5 lb box of 2 1/2" screws, and an 8lb sledge hammer. My dad paid for all of it in exchange for waxing the race trailer this week. Didn't get any work done today, should be picking back up on it tomorrow. I did get to put the sledge to use though. Port out haha.

Ya, it's been slow going, hopefully it'll pick up a lil at least...And ya, I'll be using that until I get a 100.4, I'm also gonna put a lil MTX amp and 2 MTX 10"s in a 4th that my gf and I built for her car in until I'm done. They stopped working in her car because her stock HU said F U lol. And perhaps that's the case lol.

Just two bolts in for now. One has to come out because it's too short, but I figured I'd put it in for now. I'm gonna get to Ace in a couple hours to get a few more bolts. That's probably all I'll get done today because I think It's supposed to be pretty wet all day.

My way of keeping glue from running onto my carpet haha. I look pissed for some reason haha.

Got the floor done yesterday, just need to get to Ace and get 3 more bolts to bolt it down.

Thanks

After helping my friend dig a trench for a retaining wall, I got a little bit done. Be it a very little haha. Cut notches so that the floor will lay better.

Thanks. It's coming, slowly but surely lol. Thanks, more coming soon.

Lol thanks

I don't really know what the point of these last two pics is lol.

Part of the lower floor. I'm hoping doing it like this will keep a lot of glue off of my carpet lol. Siliconing unused bolt hole shut, and siliconing around holes for the bolts to be sure that they seal. Bolting down.

Finally got a lil more work done. Starting on the floor. Gluing the step pieces together. Being proud of her work haha.

I have had them on an agm charger about once a week while they were in the garage. Thanks for the tip, I'll be sure to keep a closer eye on them.

All in. Buss bars on and all wired up. There is gonna be a lid that goes over the batteries, so all of the wire will be hidden. The fuse holders will be mounted to the top of the inside of the lid.