ztkraptor

learn to read peoples posts, I contacted Hifonics and they TOLD ME THAT THE LEVEL WAS NOT THE ACTUAL GAIN!!

The only way this amp is clipping is if there is a voltage drop across the board when the sub hits, I don't notice it, lights don't dim and there is no distortion. the level matches the input from the HU. DMM method won't work correctly for some reason with this amp. So I was doing it by ear. The volume I was getting from the sub isn't enough to clip it and isn't enough to do really any damage. new sub, i'm not going to drive it hard. As i stated before, warm is a relative term compared to the temperature outside. the only solution is to test with my oscilloscope and also test the voltage under load. It still doesn't explain the pine char smell i'm getting.

Seeing as nothing but douche bags are on, I'll just have to wait until i get to the office tomorrow and hook up the Oscilloscope. thanks

LOL you can mspaint all you want, you have no clue what or how an amp works its apparently clear.

My god, can' you read? I SAID I DON"T HAVE THE BOOST CONTROL(which hifonics says is the real gain) even hooked up to the amp.

I do realize that alot of people on this forum don't have a clue what they are talking about. I don't have time to teach you about electricity and wave forms. here http://en.wikipedia.org/wiki/Gain this will help.

You're a reall pucking prick kid ^ apparently the forum edits foul language My badd.. I retract that... I actually was not trying be a prick, but come on... I went as far as getting the manual and highlighting the section that you need to check... Then you got all e-gully on me... What did you expect? if you read what i pucking said, I stated..I said that I already matched the input output voltages. And I also said that hifonics said that the real amp gain is from the control remote. get your guido ass off of my topic if you have nothing constructive to say. Sorry mommy and daddy didn't buy my shit and have it professionally installed like yours did.

You're a reall pucking prick kid ^ apparently the forum edits foul language

Thanks, the Level is set to that of the HU. Sub is barely audible I have no external control knob because external knobs destroy things I can't understand how I am clipping a signal. It isn't making sense.

You even highlighted the damned thing and you still call me stupid..jesus kid

Jesus christ, as i stated if you could read, I said that hifonics said that the ACTUAL gain is from the external control knob. they stated that you want to match the output of the HU to the level control. I'm dumb and you can't read?

So, how do i clip a sub with a 1200 watt rms amp? there is no distortion, and the sub isn't turned up high. also, warm is a relative term when its 36 degrees outside.

OP, what are you doing?? You laugh, but have you seen the back of a Hifonics Brutus Amp? There is no gain setting, there is only an input voltage, phase, subsonic filter and a low pass filter. http://www.maxxsonics.net/manuals/hifonics/pdfs/HifonicsBrutus2009AmplifierManual.pdf check it out before you laugh and judge.. The back of my amp looks exactly the same as the 1610 or that series of amps. Yes I know that the "level' says gain in some instances, but once matched with the HU output level it isn't loud at all I'm currently not using the sub remote feature(aka knob) there is no real gain feature, From what i have read, the external control knob is the real gain. so take your roflmao someplace else?

Thanks for the responses. Tomorrow after work I'll take the sub out and check things out. I'm thinking it could be the very very tiny wood particles that the vacuum didn't pull off the wood. Its about the only explaination. I don't think I'm overdriving the sub because I havn't had it very loud. I think i need to pickup a 2 ohm resister tomorrow and fine tune the amp.. It's a hifonics amp and I can't find the gain anywhere on it..so it baffles me. It's possible the Liquid Nails wasn't fully cured and its just pulling some of the fumes out of the joints and cooking them up, I waited over 24hr before installing the sub.

Well I vacuumed out the box really well before I sealed it up. Perhaps it is microscopic dust. I mean the sub is brand new, and I wasn't maxing it out. I assume its just the varnish/glue as you said.

Ok, well My box is done, and the entire system is up and running. I have a few issues but the one and most major concern, is that my sub box smells like its burning..lol I know, weird, but it smells as if it is charing or something and I don't know why. Anyone have any ideas? Is it just the "new box" smell or what? I smelled the port area and its deff coming from the box. Also, it seems to be pretty warm. Its a 15 inch IA LI. The sub seems kinda warm too, the dust cap, not really hott but warmish. Please help. My box is about 3.9cubes and 3.5 inches of port which is about 54 square inches total, its around there.. Any help would be nice.

Why would anyone do this?

Yeah lol he just changed the wire like a week before, and was using a alligator clamp to hold it onto the terminal until he get a new terminal for it.

LOL You might wanna fix those pic posts hahah

Yeah that was a Crossover that blew up, thats the only thing that got damaged. Yeah he was bummed about his car and stuff..cuz I just sold it to him a month ago. Someone came into his lane and he swerved over into the other lane, missed the car but caught a tree. A plus for him and i think it made him feel a bit better. the HU/all speakers and the sub/amp seem to be in perfect shape. Sucks that he has no car to put them in now tho

http://sphotos.ak.fbcdn.net/hphotos-ak-snc4/hs938.snc4/75187_526573436067_61600232_31094827_188159_n.jpg http://sphotos.ak.fbcdn.net/hphotos-ak-snc4/hs1150.snc4/149244_526573446047_61600232_31094828_1873210_n.jpg http://sphotos.ak.fbcdn.net/hphotos-ak-snc4/hs897.snc4/73079_526573750437_61600232_31094845_1891763_n.jpg http://sphotos.ak.fbcdn.net/hphotos-ak-snc4/hs011.snc4/33907_526573925087_61600232_31094856_104572_n.jpg Hes ok, his gf was in the car she broke her ankle but she will be ok We were all just amazed that the box has like barely any damage to it, and it blew the back seats of the car apart like they didn't even exist. Crazyness

I'm not following you? Ive come to understand that fumes from wood glue, liquid nails ect Can effect the glue used in the fabrication of the sub itself. And it looks as if you will have to build the box around the sub, so the fumes could effect it.

pictures or it didnt happen , and dont think about finishing anything untill you know you like the outcome of the enclosure, it could jus tbe total ass and youll want to rip it out. never know. Here we go so far. It better not sound like crap... Cuz its not coming out of there...lol

Well, The bottom, sides, back and port all are in the trunk, just have to install bracing and then the front panel and top, and the box will be complete. Should I carpet it?

I hope your glue won't effect the subs integrity