March 18, 20169 yr 56 minutes ago, Adrian_D said: Yay transmission rebuild: All the kings horses and all the kings men couldn't get me to put a transmission together again.
March 18, 20169 yr 10 hours ago, dem beats said: And make her a handmade card. Broads love that shit. Glue a leaf to it and shit will Be on like donkey Kong. Hand written love note is always a good addition too.
March 18, 20169 yr On 3/16/2016 at 9:50 AM, ///M5 said: Good. If you need something call I just wanted to let everyone know that Sean"s equipment is amazing (Polytec that is) I got to spend about 4 hours setting up measurement points to measure micron movements, then run it in the Doppler software and watch 3 different views of the sonotrode, we then made some material cuts to get the results we needed to make sure there were no frequencies in our desired operating range and ran the Doppler again to see if the face of the sonotrode was working optimal. It was truly awesome for me to get to do this and see how it works. I now have a much better understanding for how small those unit can measure and how the Doppler graphs work. I worked my manager pretty hard to buy me one, but so far he is resisting.
March 18, 20169 yr 5 hours ago, dem beats said: Need to buy more weight. Bangin out 300 for reps finally. That feels so juicy. And I also feel like a bitch. I used to warm up with 350 So I could bang out 720 for a few reps on the smith or >600 free. C'est la vie. Ain't nothing but a peanut. Beast mode!
March 18, 20169 yr I finally got to spend time with a very good buddy in his element. Over the many years of working in my facility, I have help him develop die cutter stations for the nonwovens application. Yesterday we spent the day at his machine shop and way more than I had expected! I even got to make some cuts and set up the tool angle for sharpening. Here is a link to give you a little look. http://www.icd-inc.com/gallery/
March 18, 20169 yr 6 hours ago, dem beats said: Need to buy more weight. Bangin out 300 for reps finally. That feels so juicy. And I also feel like a bitch. I used to warm up with 350 So I could bang out 720 for a few reps on the smith or >600 free. C'est la vie. Ain't nothing but a peanut. 300 on what? I consulted a multi rep max chart and I should now be in the 700 club! I based everything on a 5 rep "max" even though I do 5 sets of 5 for everything but DL. Doing 2 plates on squats now. Can't wait to be doing 2 plates on Bench
March 18, 20169 yr Was it a single point or scanning? They have both. I assumed single from the text.
March 18, 20169 yr 1 hour ago, nem said: I finally got to spend time with a very good buddy in his element. Over the many years of working in my facility, I have help him develop die cutter stations for the nonwovens application. Yesterday we spent the day at his machine shop and way more than I had expected! I even got to make some cuts and set up the tool angle for sharpening. Here is a link to give you a little look. http://www.icd-inc.com/gallery/ Awesome!!
March 18, 20169 yr 15 hours ago, ///M5 said: Shit. My wife turns 40 this weekend. Any ideas for a gift?? One of these. Fun times for all.
March 18, 20169 yr 14 hours ago, dem beats said: And make her a handmade card. Broads love that shit. Glue a leaf to it and shit will Be on like donkey Kong. That would be Donkey Dong since we're speaking of Sean.
March 18, 20169 yr Dammit, I drove an older Mustang and I REALLY enjoyed it more than driving Ava. It's like the difference between my truck and Lincoln. I like both, but the truck is just so raw and in your face. The Lincoln is quiet, soft, and relaxing, like you're not even driving. I don' think I should keep this car.
March 18, 20169 yr 5 hours ago, ///M5 said: Was it a single point or scanning? They have both. I assumed single from the text. We did 20 points across the sonotrode, I believe.
March 19, 20169 yr 11 hours ago, nem said: I finally got to spend time with a very good buddy in his element. Over the many years of working in my facility, I have help him develop die cutter stations for the nonwovens application. Yesterday we spent the day at his machine shop and way more than I had expected! I even got to make some cuts and set up the tool angle for sharpening. Here is a link to give you a little look. http://www.icd-inc.com/gallery/ Very cool!
March 19, 20169 yr 13 hours ago, MKader17 said: 300 on what? I consulted a multi rep max chart and I should now be in the 700 club! I based everything on a 5 rep "max" even though I do 5 sets of 5 for everything but DL. Doing 2 plates on squats now. Can't wait to be doing 2 plates on Bench I can squat it about 10 times, bench 2-3, deadlift indefinitely depending on time between reps.
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.