edouble101

After all Fi design and builds SSA woofers which are the best so this sub has to be good

You install looks good, much better than most. If you didn't achieve your goals with it, now you have a baseline!

I scooped up a few sets of mids and tweeters slightly used or on sale. I built a baffle that I can demo these drivers on and I compare notes. The audible differences between mids is drastic. Tweeters not so much. I have yet to hear a midrange that doesn't need a tweeter. A tweeterless system lacks "air" or "atmosphere" IMO. It is a personal preference and I recommend that you buy a few drivers and test them yourself. If you are careful enough with the speakers you could even return them to parts express afterwards. BTW I also recommend you buy drivers based on installation limitations than t/s specs. Hearing is believing, specs don't make a sound.

Is the suspension stiffer on the rearward stroke? Probably not a big deal for a subwoofer though.

Product Brand & Model: Morel Piccolo and MT250 http://www.woofersetc.com/p-4789-supremo-piccolo-morel-1-exotic-inverted-tweeters-with-lotus-grilles.aspx http://www.woofersetc.com/p-11298-mt250-morel-28mm-6-ohm-silk-dome-tweeters.aspx Condition of all items: BNIB as shown in pictures Total Price: : Piccolo $470 shipped MT250 $290 shipped Paypal only, no trades Shipping Terms: : Tracking and insrance, either FedEx or UPS. I normally ship no later than next day. Pictures: - Unless you are a Upgraded member, or your last 10 iTrader feedbacks are positive, you must post a picture of the exact item you are selling.

Nice!

You have to admit man, that's easy info to get. You could have found it faster than the time it took you to make this thread.

I saw that too. I passed it off as being a recone.... Hmmm.... BTL redesign?

Product Brand & Model: Eclipse 32440 Condition of all items: New, like new, very good Total Price: : <$300 depends on condition, PM me your asking price Shipping Terms: : I'll pay

Holy shit

Thanks!! SOLD

1. Product: *AUTHENTIC* MOREL® HYBRID INTEGRA 602 6-1/2" 2-Way CAR AUDIO COAXIAL SPEAKERS 2. Specs: 6-1/2" 2-Way Hybrid Series Coaxial Speakers w/ Passive Crossovers Power Handling: Peak: 600 watts per set / 300 watts each side RMS: 200 watts per set / 100 watts each side Impedance: 4 Ohms Frequency Response: 50-25kHz Sensitivity: 91 dB Paper composit cone Hexatech™ Aluminum vc EVC™ structure Acuflex™ coated tweeter Hybrid magnet motor Shielded magnet MXR direct crossover Hybrid Integra: integra time aligned structure Uniflow™ chassis Octopus Grille Large 2" voice coil Includes pair of MXR passive x-over networks 3. Description/Condition: BNIB 4. Price: : $425 shipped, paypal only NO TRADES 5. Pictures:

I know nobody on this forum that repairs amps. Although I do know a guy that does excellent amplifier repair and restoration. You can look home up on DIYMA (ShawnK) or I could PM you his number. Extremely knowledgable guy.

BTW those Knu distro blocks are AWESOME!!!!

I am helping a buddy revamp his install. He was using a JL Audio component set for the font stage and JL Audio 12w6 subs powered by JL Audio Slash amps. He bought my P99RS from me and is now running active I gave him a quick four hour tune while drinking some beers and we got the JL's sounding really good. Good enough to be winning competitions but he wanted more. He bought a set of Seas components and is hoping for a better sound. I recommended a different route but this is what he choose. We have a lot to go yet on revamping his install. Here are a few pics of the Seas midrange install. Old MDF baffles that I told him had to go. I made new baffles out of cutting board. Unfortunately I didn't take pics of this step. I used my router with a circle jig to cut the baffles. The boards are 3/8" thick so we doubled up on them to get 3/4". I used hot glue to join the baffles and used ht glue again too seal them the to metal door and used four screws to fasten them. I applied gasket tape to seal the drivers to the baffles since the baffles flexed out of fat once being attached to the door. We are no done yet with this install, I will have to take more pics once we meet up next. His setup will be in the winners circle for 2014

Finally got the amps installed around 11pm yesterday. I quick listen with no tune : sub bass is fairly flat, really digs the lows with authority . Even with no tune whatsoever the "up front bass" was very present with a blues track that I demoed. Amplifier gains were set about 3/4 max and we definitely have to revisit those for more adjustment. The front stage needs retuned badly. Literally have every inch used in this trunk.

Truck looks good real good

NICE!!!!!!!!!!!!!!!!!!!!! I have a set of MW4's and MT250's, I know they make good stuff! If you are getting rid of the 6.5's I am interested in buying.

I am really anxious to see how the doors turn out. Those TB 6.5" midbass drivers have a huge ass, damn!! The TB W4 Ti driver is a great mid. I believe you are using the bamboo version which I have not tested. The only midrange that I have heard that I like as much as the W4 is the CSS VWR126X, smmmooooottthhh mid. I do not know what tweeter you have there. I have tested a bunch and I am anticipating the KAXBLTWT. Should be an excellent small format tweet..

Congrats on the win!

If have used an Arc Audio KS series amplifier and had no problems with it.

Depending on which Boston Acoustics sub you have, I would build a ported enclosure for it. If that doesn't satisfy your needs then I would consider more cone area and double the amplification power.

sssllllooooowwwwlllllllyyyyy getting this done. Red paint Amp rack base is welded up One of the mounting brackets before paint prep Painting the base and supports a dull black Tape off

Any new pics to post?

Good job