GM959808

Well...... I guess I will just build it and hope it doesn't sound like junk

I work in Nashville. Any help would be greatly appreciated.

Can anyone help with this box design?? I don't know if the port configuration will work. Help please??

Don't know why the box is showing upside down. Sheesh. Anyway... anyone have any ideas? Bad idea, decent idea, port area too small??

I think my port area is way to small. Maybe something like 8.5"x3.25"x17" be better? Boxes 2 and 3 have those port dimensions.

Hope this image works. Its a very rough sketch of what I'm planning. It's roughly 2.5 cu. ft after port and before sub volume is removed. Subs firing down, port forward. This is roughly the outside dimensions I have to work with and am open to other sub/port configurations if they make sense. Subs will likely be SA-10s or maybe Gcon 10s. Torres calculator showed 32 hz tuning frequency, but I'm confused why it asks for a port diameter and port dimensions for a slot port?? Any opinions?

You wont get that direct sound, if you point a driver almost at you and then point it at the ground, you can tell a difference. Different type of sound, its not super pronounced but it depends on what your looking for. If you want it to look really clean and hidden then Id say go that route, but I personally prefer the sub facing up/at you. The only other way I could face the subs in a console enclosure would be out towards the sides. I'm concerned they would get punctured in that configuration.

Negatory, gotta be able to haul the kiddos around

I think I've decided to go with a console enclosure. 2 10s, ported. I'm pretty sure I can get at least 1.25 cu ft per sub. If I face them down, how much will that affect how loud they get??

Gotcha. I think I may build my own ported console enclosure. If I do go sealed, I was thinking Sundown SD-2. If I go ported I was looking at SAs or GCONs. In a console enclosure, If the subs are side mounted, would it make a difference which direction the port was aimed? Single port or 2 ports?

Why sealed if I did the console? I think I could get 2.5-3 cu ft if I extend it forward pretty far. That's unusable space up there under the dash anyway.

That's what I mean. My previous systems haven't had that low, booming bass that I want. Probably in the 45hz and below range.

I have the bucket seats. Thought about the console style. Think a single 10 in a console style, ported, would be way better than two 10s sealed under the seat? I haven't been happy with my previous truck boxes at all and don't really want to go down that road again.Tell me more about cutting the back wall. How it affected the vehicle, how difficult it was, etc. Center console ... We have a few on our team. A single downfire / port forward enclosure ... A single Isoberic front fire / port forward enclosure ... And a dual chambered pair of 8s side fire / ports forward enclosure ... They are all fairly low tuned for SQ and sound great !!! Guess the possibilities are endless there ...As for the cut through ... A LOT of work, add a bed cover, and keep all of your room in your cab. When built and installed correctly, works like a champ !!! Just takes of room in your bed if you are willing to give some up ... Personally I wouldn't consider a cut through unless you are planning to run something like 4 10s or better ... Just saying Well if I went with a cut through I've thought about anything from 4 10s, 2 12s, 4 12s or even 2 15s. I kinda doubt i will go that route. So the center console type system should give me FULL range of sound? That is my biggest concern. My previous 2 10s in a sealed box setups didn't have the lows that I wanted. Don't get me wrong, I want it to hit hard too, just sound quality is more important. Where could I get the box designed/built? I'm decent with woodworking but I don't think i would be happy with a standard mdf looking enclosure for my console. I would want it to look nice.

I have the bucket seats. Thought about the console style. Think a single 10 in a console style, ported, would be way better than two 10s sealed under the seat? I haven't been happy with my previous truck boxes at all and don't really want to go down that road again. Tell me more about cutting the back wall. How it affected the vehicle, how difficult it was, etc.