jcarter1885
-
Content Count
12,016 -
Joined
-
Last visited
-
Days Won
123
Posts posted by jcarter1885
-
-
It's hard to get good pictures with the trunk light because it's so damn bright, but in person it's perfect. The entire interior of the enclosure is covered in blue light. I'm glad I didnt pay for the LEDs I usually get installed in the enclosure because I never use them anyway.
1 -
looks dope and I love the progress so far. I can't wait to see this wall
0 -
I will take some night shots one day soon, as much as I loved the white enclosure with the blue lights it stood out way too much at times. I didn't want it covered in bed liner again so I went back with the traditional carpet look and it came out fantastic.
1 -
-
-
This enclosure turned out bad ass, I even had my builder make a matching beauty board to keep the enclosure in place.
1 -
Some daytime pictures of the new voltmeter placement
1 -
This light is so bright it's hard to get decent pictures with them on but it came out dope
1 -
Had to clean up the wiring some since it's exposed but can barely be seen, separated power/ground from RCA signal wire. Y'all know I'm OCD about wire management especially if I can see it.
0 -
Used this ammo to hold these volt meters in place while the double-sided tape adheres to the panels.
0 -
Hole cut for cat-5 cord for Sundown bass knob/volt meter.
0 -
Permanently mounted the cars' main voltage meter with double sided tape, looks damn good if you ask me.
0 -
I needed to clear my mind so I worked on the car, got two things accomplished. I figured out how to remove this side panel to get access to my gear box area in my center console. I moved the USB cord coming from my radio from the passenger side where the shop installed it, to the driver side for ease of use. I also made a permanent spot for my car's main volt meter which monitors my up front voltage. I'm working on a spot for my Sundown amp bass knob/volt meter next.
The volt meter will cover the factory USB port since it is no longer needed, hence why I drilled a hole in the housing to feed the wire. I'll use double sided tape to hold it down tomorrow once I clean the area with alcohol.
0 -
On 10/6/2022 at 7:13 AM, Aaron Clinton said:Hey!!! Nice to see some SSA in that ride.
I sure did look for some Xcon or Zcon 12s when I was buying subs, they were at the top of my list but no luck. Still mad I've never tried an Xcon till this day.
0 -
This is how it looks now after the work I did earlier, I'm happy with the outcome.
1 -
These next photos were before I put some work into the car because of my OCD, hated the excess wire I had goin into my DSP. So I untaped it and cut the three excess wires for a cleaner install. I also made the Sundown Salt-4k remote wire smaller since it the connectors on these Audio Control doesn't accept big gauge speaker wire well, especially with thick wire jackets.
1 -
-
On 9/28/2022 at 12:08 AM, black 02 said:are they dual 1's ? or did you take advantage of FI offering Dual .7 coils ? always get .7 coils if at all possible when running a dual woofer set up & 1.4 coils on a 4 woofer set up ..
If I were competing then I would have but for daily I'll be ok with the D1s. But I appreciate ya though
0 -
On 9/23/2022 at 10:12 PM, Tirefryr said:Those look amazing!
Thank you, I agree with you. Fi always makes beautiful subs
0 -
Who would of thought that I would have twins, especially at 55lbs a piece. My trunk, suspension, sunroof and car in general are going to hate me.
0 -
I have a love hate relationship with installing sound dampening but it's so worth it at the end.
0 -
can't wait for the build log man
0 -
Time for a new substage, Dual 12s but which one's:
Sundown Xv3s
-or-
Fi HCs
0 -
On 9/2/2022 at 7:19 PM, Tirefryr said:Man, it's lit up like a strip club in there!
Where those dollars at? Haha
0
2021 Volkswagen Passat Rline
in Build Logs
Posted
Speaker connects outside the enclosure.