General Audio

ok so i just checked my tweeters out today and their blown....so i was wondering what tweeters should i get ( i just need two) and the ones that blew were diamond audio s600 hex. Also should i use bass blockers this time because i believe that they blew because they were getting to low of a frequency.

i have been searching the web for some 0 gauge ring terminals and all i can find is 2 packs for like almost 10 bucks or each sold separately, but i need like maybe 20-30 total. anyone know where i can buy bulk packs of them....??????

So my front speakers stopped working and its not a big deal they were cheapo sony 5 1/4"'s, temporary until I got my components. And it was raining one day while I had the speakers were out and I saw the amount of water that runs down the door and gathers at the bottom and then drains out.. This cannot be good for my speakers, and considering there was rust on the back of the burnt up speakers this has to be the culprit. I was planning on putting a nice set of components in but there is no point if they are just gonna get destroyed by rain water.. What would you guys do?

Something funny has been going on with my sound system the past two weeks. I've been noticing that the bass from my subs and door speakers sound distorted . This is not all the time though, my system will sometimes sound perfectly clean and then go back to playing with the distorted signal again. My electrical is currently stock with 2 gauge wire, a capacitor and my sub amp is a sundown sa 125.2 which does get very hot. I have previosly blew all the fuses in my amp but they were replaced at a local shop. My voltage is usually bouncing around between 10 and 12 according to the meter on my cap. What do you think my problem is and how can I fix it?

let me know what you guys think

Ok, my dumb ass can't figure this out. I have a pair of dual 4 ohm 12's. If I wire each sub in series to make 8 ohms then wire the 2 subs together to get 4 ohms, would that mean a pair of strapped 1500d's will see 2 ohms each? Thanks for any input!

I have some questions, hope I can get help. Where can I buy 2/0 AWG wire? Whats a good brand? model? Does 2/0 gauge really make a difference over Zero (1/0) gauge? Is anything thicker (3/0, 4/0) than 2/0 overkill and waste of space? Thanks

ok so i have 2 dc level 4 15" with the level 5 dual 1 ohm coils and they are rated 1500 a piece and im only pushing one hifonics bxi2010d (its max is 2000 at 1 ohm) to them so i know its not nearly enough power that they can handle and i know that the amp prob isn't putting out 2000 at 1 ohm. My question is should i get another hifonics bxi2010d and run one amp to each sub or should i look into something like sundown? like their 3500d or something like that??? thanks in advance for the help??

hey guys, building a new box for my 18" btl, as the old one wasnt done right and was my first build so yeh, here are the specs, just wanted to run them by you guys before I go off and start. cheers

hey guys i have 18in fi BL dual 1ohm being powed by JBl gto 1200 amp and just wanted to make sure i get a speaker wire that will allow enough flow of power and still fit. any help i'd appreciate it.

I built 2 boxes lately and I will be doing a 3rd soon, and I love buying tools so I "need" a router. I dont want to spend an arm and a leg, but I will spend what is required to have a decent setup(not harbor freight). I want to be able to do speaker hole cut outs with it, round the edges of the box and ports, and anything else that is usefull. Im not sure what bits I would need either, I was thinking 3 one to make cut outs, one for rounded edges, and one to flush mount on a double baffle. Also I think I need the jasper circle jig unless there is a better/cheaper alternative.

ok, im have a big, big problem right now. i dont know what i want to do with my truck. im really into the whole "wall your truck out and go deaf" thing. but now that i have a extended cab truck, i dont know that i want to do it. im still trying to decided on giving up all that room to do this. i was talking to a friend, and he asked what if people wanted to go ride around and stuff. so i dont know what i really want to do. im stuck in the middle here. on one side, i love car audio and on the other, i like chilling with the friends. can anybody sorta led me in the right direction?

I am looking to upgrade my current setup. I have a Directed Audio D2400 pushing 2 Hifonics Brutus Subs in a ported pre-fab box. It was a pretty good setup, but now I want more. I have been looking at the AQ sdc2.5 15" woofer. I would want to power it with a Hifonics 1200D Brutus Series amp. Running it at 2 ohms, which would send about 900 rms to the sub. I researched, sub and amp is a little under $400 total . Is there any setup that is better than this for the price. They are going in the trunk of an 04 Grand Prix. Thanks Justin

My bro has some mach 5 spl15 and wants to finally do something with them. I remember he recommend 1500 rms for daily but cant remember box size. does anybody remember? the spl12 on the website say 40-70L.

Hi fellas. I am on the market looking for new eardubs. I was pretty happy with my original ones from Sony Ericsson till they stop working and I bought some cheap ones which are very bad. My phone is SE Walkman W810i. The sound was awesome with its eardubs and I am looking for something at the same or better level of quality. Must feel good in my ear, sealing good the environment sounds like road noise etc, very good response in all desired frequencies and deep bass. And not very expensive. I see some for 20-30$ on ebay with shipping which sounds good. I have no knowledge at all about eardubs and that's the reason I am doing this thread. Read good things about Sennheiser a…

Ok here is where I'm at, I have a Pioneer AVH-P4100DVD (2) MB quarts 6 1/2 components (2) MB Quarts 6x9s powered by a Soundstream PSA4.260 and (2) Soundstream RW 12 Subs (600 watts RMS each) Powered by a SoundStream PSA2.760 (760 Watts RMS bridged @ 4 ohms) Wired like so: How ever I was not satisfied. And low and behold, today my PSA2.760 took a dump. I called the company where I purchased it and they said they will send it out to get repaired or I can upgrade it for a small price to a Soundstream PCA-2000D. This amps specs are 4ohms 1100 watts, 2ohms 1500 watts, and 4ohms 2000 watts Bridged. What I wanted to know since this new amp is more powerful should should I add…

So I was searching this forum and others and I found this stuff called BIRCH PLY. my thoughts are it looks sexy and cost more than mdf. but my question is how does it compare to mdf? does 3/4 mdf= ½ birch ply or 5/8 if ½ is to small? are there any downsides to using this type of wood? also can someone confirm if birch ply is 1/2 the weight of mdf? (say 3/4 mdf vs. 3/4 birch ply = 1/2 the lb's) I am considering using this type of wood for my box rather than MDF b/c my next setup will be a heavy one and eliminating weight will be good in my part or I will HAVE to buy a luggage kit for my car which is ~300$ my next setup will be: 2-saz2000 = 40lb~ 2-NS 15inch v1 subs = …

well my set up is in the sig. i played the three6 mofia song late night tip (slowed down) and my amp cuts out. i can play any other song same vol and every thing just asking if some one knows y it dose that.

Hello all, as mentioned in my newbie intro I made my way here on recommendation while searching for a solution to add some bass to my 2010 Camaro. I wanted to post up and see what thoughts/suggestions others may have. Here is my current set up: 2010 Camaro - stock. No upgrages to electrical - stock sound system which is the Boston Accoustics. What I am wanting to do is add bass that is clean and tight. I do not want really to be noticed 20 feet away and I do not want the "excursion effect" where its all warbley and distorted. I typically listen to Rob Zombie, Godsmack, Rhianna, Lady Gaga, ect. No rap. What I am looking at so far: Subthump sealed mid size side drop in…

im running 4 amps and a additional one for mids and highs, with a total of 8,360 watts. i wanna go XS Power, what model should i get and how many? please give me feedback, i also have a 250 amp h.o alternator if that helps. ?

I usually am used to seeing boxes with the shape of a port like a L, but the box was to be tuned to 32 hz and is missing the piece of wood that is found behind the cutout usually... what is wrong here?

Lately I've been looking into Fibeglass subwoofer enclosures and I'm just wondering if they function any differently then an MDF enclosure? I've done some research and wouldn't think it would affect the sound if it was properly constructed but alot of people online have said that MDF is the way to go. Is that just because MDF is so much easier to work with or does fiberglass really affect the output of the woofer? Also, after looking around the site alot of people here use fiberglass for speakers and midbass drivers but not many use it for Subs and that got me worrying about it too. If any of the Guru's here could shed some light on the subject it would be greatly appreci…

I saw lots of songs on a list here but I noticed that there were no songs from the Southern hemisphere. I know of many songs like Reggeaton that have awesome rythm and bass. I uploaded one to one of my websites. Take a peek and let me know what you think. Listen until the bass kicks in. Thanks. music

So like it says. Where do you guys have your bass knobs? What sneaky spot in your car did you hide them? Do you have them in the open? Pictures would be awesome. Trying to get some ideas.

Just ordered a Sundown Audio SAE 1200d. Finally after 2 months