General Audio

Heres a review of the unit. They also have a group buy at caraudio.com going for it. I read the whole thread and I seem impressed. I downloaded the plugin for windows media player and I like the way it sounds on my headphones. I don't know if I would buy the unit, but maybe in the future if more people have good results. However, it looks very promising. I am gonna copy the text here because it is hard to read at ECA. http://forum.elitecaraudio.com/showthread....threadid=109732 Okay so here it is. I feel i've tested the unit for long enough to get a good feel of what its capable of. First off i just want to say i have no connection to Waves (the maker of maxxbass) and i D…

i have this http://cgi.ebay.com/TSUNAMI-RDS9100-UNIVER...1QQcmdZViewItem and i hooked it up today but it says my voltage is 8.7 when i go back to the amp it says 14.05 anyone know what could be wrong? when i check my wires that go to the tsunami connector and put my dmm on the pos and neg it reads 14 but not on the unit. i bought this brand new 4 or so months ago and dont have the packaging or anything. and i cannot seem to find the manual online anywhere.... today i hooked it up to just my starting battery and it still was reading 8.7 any help is appreciated.

I have the MB PVF 213's in kick panels, and want to install these in my door. It says to run wires through the 213's first then out to the 164's. Each has it's own cross over so why would you do this? I'm running them off a RF T600-4 4 channel amp. I thought you would just run the 213's off front channel , then run rear channel to the 164's and you would be good. Then set my cross over's on my RF 3sixty.2 to HP on front , get it were I want it at, then set the BP on rear where I want it at and it would be good to go. What am I missing? What would be good settings for the cross over points to start with? Thanks

Ok I use MDF on a weakly basis and I have never had any problems with it doing anything to me while I

Any recommendations for a MDF paint primer? I would prefer the typical gray color of primers. I've heard that you need a special primer, but I wasn't sure. I did a search but most places said use primer as a general term and didn't specify a certain kind of primer or anything. I need know to smooth out and prime my old DCON boxes and also some SSA logo cutouts. Thanks

Does anybody know of any places that sell quality mdf rings? I want some rings made for some 6 3/4 mids. The only reason why I'm not trying to make them is because I don't have the tools. I would hate to buy all the tools needed just to make a ring or too. I know those tools would collect dust. So, I would rather just pay someone because its easier for me.... Yes, I know about the swelling of mdf when wet. I plan on treating them with rubberized undercoating and applying dampener to fully cover the ring.

Whats involved in doing a MDF roof? My headliner is shot, and i don't want to spend 350 for a replacement headliner. I think it would be nice cause I could make a console for the roof to mount stuff..

In case you couldn't tell I have a pair of Seas Excel 7" W18NX-001 & Seas Prestige 27TBFC/G tweeters. These things sure are beefy. I've never seen a tweeter quite like this one up close in real life hehe. Can't wait to get these things mounted and installed this weekend. I will be posting a nice review on them and the MD43 after about a month of listening and making sure everything is all set up and ready to be assesed.

How do you use hz and know how to use tuning? How do you know what will be the loudest frequency or which one creates the loudest bass? quen

So who all is going to be there, gonna be a 1x show with alot of cool rides and setups. Anyone from SSA gonna be there? Will be at the golden state mall in bakersfield california

When: Oct. 5th Registration & Cliniques Begin @ 9 AM 3X Triple Points - Judging Begins @ 11 AM Where: Bullitt County Fairgrounds I-65, exit #112 - 15 miles South of Louisville Shepherdsville, KY LSQ will be inside Hosted by: E2 Audio/Team H.B.I.C. Trophies for top 3 places in each class, as well as other awards, and payouts for class winners if over 4 entries in your class. Here is a link for more info. http://www.mecacaraudio.com/flyers/10-05-08KY.pdf If your near this would be a great show to come out to.

I was at a show and I got a picture taken of me in front of my truck and the guy said he was going to put in the MECA Magazine. Where can i find this?

OK, i've been doin research on this and i can't get a hold of excessive amperage or Iraggi so maybe someone on here may know. I had planned on running a Lanzar 6000D with an Alpine PDX 4.150 300A iraggi alt with HC1800 and HC2400. Well, i've been doin some research on alts and it said once you reach 300A alt case size, it is extremely large. In order to have adequate cooling, they are normalls about 12" wide by 18" long! There is no way that could fit in there without doin some extensive re-running of the AC lines, but Iraggi makes alts this high which is odd. I drive a 2007 Scion tC by the way, 141hp dyno-ed stock auto, 161hp at the crank. Ok, it is also true that for …

http://www.ce.org/certifications/mecp/default.asp what r the answers to these test??? david i say your the smartest.. let me know

I am a Mecp advanced level installer working on my masters certification, and I was just wondering I work for Best Buy and the certifications are mainly for pay raises because you make a lot more if your certified. Anyway my question is how much does the certifications matter outside of buisness like Best Buy. I have looked at a lot of job opportunites and none of them really seem to care if your certified or not as long as you can install.

well the positive on the box terminal melted and warped. this is the second time it has melted but the first time it didn't get ruined completely. but this time it did. the wiring from inside side of terminal to sub is 12g and the wire on the outside side to amp is 16g for 2000 watts rms i know it should be 8g. i know. but havent had the money to buy any yet. both times this has happened it has been the same case: the sub wouldnt hit until almost at 2/3 volume. or if i messed around with the terminal peices. (tightened and loosened them) in the first case i came to the conclusion that the two gold prongs that you see in the pictures on the inside side of the terminal…

Hey there everyone....I have a few friends who do a little free "tweak and test" thing for SPL every couple weeks. The next one is Saturday, August 20th (weather permitting of course.) It will be from 4pm-9pm at the Brunswick car show. The city holds a car show/crusin gig every Saturday at Laurel Square Shopping Center. They have their own space to do test and tune, just look for the EZ-UP tent and some loud cars around it. The address is 1733 Pearl Road, Brunswick Ohio 44212. It's about 18 miles south of Cleveland and about 20 miles north of Akron. Of course its free. They will be having a competition there in the fall where all money paid in to compete gets paid back to…

I have this mojo sub and I needed to build a box for it. I have tested it and it is 4ohm dvc. I wanted to know if anyone had the specs to it like freq. response. and all that good stuff. Also I would like to know if anyone has had any experience with it and how much power I could give it.

have looked and searched and have found almost no info about them http://www.champaudio.net/merlon_menu.htm thanks for any help.

so i see alot of people like to mess with all the "professionals" at audio shops and such, so please, share your stories

Just curious if anyone on these forums listened to metal, and what kind of setup they had... Ive kinda been drawn away from spl and more towards sq. i would almost assume that a sq setup would suit my needs more than a spl setup, considering the type of music i listen to. Dont get me wrong, i listen to a select amount of rap, but, the majority is going to be metal... So i guess im looking for some conformation on this situation.. much appreciated

Anyone near the Atlanta area and would like to hop on a meter let me know. Here is my little niche in the garage. It is a Linear X. Not the greatest spot, but it gets the job done:)

I have called all the local car audio shops trying to find someone with a TL. I just don't want to spend $650 on a meter, when I could buy another sundown audio 3000D for that. I'm just asking if anyone knows of a place that has a TL anywhere in the montgomery or birmingham alabama area. Thanks. Are there other types of meters that are close to that of the tl, but aren't as expensive?

I know the Term-LAB is by all means the best to use but is also really expensive. Are there any other meters out there that are good and cheaper?

Looking for someone with 1200+ RMS @ 4 ohm willing to spare a day and test the SoundSplinter RL-s with me.