SPL & SQ / Fabrication

I'm going to be building a box for my friends Ram. Aero ports seem to be the only way to port this box but I've never used them before so im looking for a little help. Box will be going under the rear seat. The sub is a JL 10v3v3 Box will be about 1.33ft after sub displacement Tricky thing is I only have about 3 inches of height for the areo.(Rectangle box with wells on the bottom) The Rectangle part of the box will be W54.5-D13.5-H3 JL Recommends 32Hz 84.7 Slot Port Area

Im needing help i only have a phone no computer and I'm wanting a box built for my new soundquebd hds3 12's i got two subs and my dimensions are 30" deep 35"widr and 18"tall wanting it tuned low around 31-30hz I'm also wanting subs on top facing the roof and port facing the back hatch I'm using a 1200.1 super d class mono Zeus amp with big 3 upgrade and 0 gauge wires but I'm unable to access these sketch up things and box calculators so can someone please help a fellow bass head out and please send me a blueprint of this and a cut list of sides and port and everything pretty please b greatly appreciated

Ok so I am going to build my 3rd sub box and i want to know how to cut the bracings and that stuff. And how to port/tune you box. I am going to put it in a car and i want the sub facing upward and the port too. I do not want an L ported i want like square type one. My sub is a 12 Fi SSD. I want it to use half of the trunk but not be so tall just like an inch after the sub fits. But mainly i just want to learn how to do square ports. Any help plz.

a. Subwoofers in question, number of subwoofers & subwoofer size: Dual SA-10's b. Amplifier being used, specifically the model number: 1200 watt Hifonics Brutus (will probably end up upgrading it to a 2000) c. Fabrication skill level: will be made by a box builder d. Preferred material to be used (i.e. MDF, fibreglass, etc): mdf e. Vehicle which the subwoofers will be used in: 93 toyota celica f. Musical preferences: rap g. System goals: SPL all the way h. 37 Hz range i. max dimensions: 38 length x 20 width x 16 in height

okay new here and was told that you guys could definitely put me in at least a general direction. here goes I have a customer who had three 12" L7's powered by 3 hifonics bx11200's in the trunk of his 96 J30. the box it self was a sealed, non-separated, box that was just big enough to wrap around the woofers and fire at the rear with the box jutted up against the gas tank that resides there. he is asking if there is any way to build a box that would be noticeably louder yet still retain the punch of such a constrained box. he doesn't mind the loss of his trunk so but the real challenge is figuring out how to get the sound to penetrate through the obstacles within the trun…

Hi guys, As the title says, i need a box for my sa-8 but i don't have an enclosure yet. I already saw this thread: But i wanted to get your opinion with this one: can you tell me which one is better? The only difference is the port area. The second one is bigger thus have a higher tuning. I listen to hip hop, rap music most of the time by the way. Any help/insight is appreciated. Thank you!

I was wondering how to build a ported box for 2 18" btl loaded each one in its own chamber for a 03 Yukon and how to tune it between 30 and 35 Hz. I'm looking get some serious bass. What are some dimensions I can use with the speakers facing up? I will be running them on two saz-3000d. Hello again I'm looking for spl in my 03 yukon. I am looking at running 2 Fi Btl 18" on 2 Saz-3000D amps in this amount of space. H 21" W 46.5 D 22-28". So what do you think? I need help with the box and port dimensions. Once I have an idea I will start the building. I need all the help I can get. Thanks

max dimensions are 17"h x 31"w x 27"d i will be running a crescendo bc2000 thinking pretty much the same thing anton miller has setup in his cavi it seems to be really efficient i want to be able to hit the low's really well so im thinking 30hz tuning ? this is what i have come up with so far 27w x 16h x 25d using 3/4 mdf should get me 5 cubes after sub displacement of .14 i should be at 4.72 using a 6" aero tuned to 30hz i need 14.5 inch flared and with port displacement i should be at around 4.5 cubes witch is max recommended for the sa-12's if im doing something wrong please let me no i plan on building tomorrow

These will be going in the back of a Grand Cherokee. I was originally thinking a single SA-12 but I think I like the idea of less box so I can keep more cargo area and my goal is a daily driver SQ setup so I think the 8's will be just fine for my goals and it stays within my pretty small budget. I have never built a ported box before so the design, tuning, and porting all are things I don't have a grasp on. I want to do a box that is wedge shaped to maximize the space available while leaving as much cargo area as I can. One thing I am not sure about is whether or not to go rear firing or top firing. The rear firing will allow for a slimmer box but I want to make sure I am…

I just bought a 18" FI BTLN2 and was wondering what is the best way to build my box. It is going in the back of a '97 nissan pathfinder. I know you need 3/4" MDF for the box but can you use 1/2"? thanks

Doge Neon HU - Alpine CDE-172BT Front Stage : 8" Beyma 8G40-4 in doors Midrange and tweeters still to be decided. 3.5" Pioneer bullet tweeters in dash atm. Sound Treatment: Spectrum Sound Deadner sprayed on undercarriage Front Doors treated thoroughly. Sealed and deadened as good as possible. Car floor and trunk will be deadened and get CCF/MLV treatment. Electrical: Aftermarket 200 amp alternator 2 runs of 2/0 Royal Excelene welding wire run from hood to trunk Big 3 with 2/0 Royal Excelene welding wire At least 1 more battery will be mounted in the trunk area. Amplifiers: (2) …

have an 18" aa havoc and it's going into a 98 pontiac bonneville....want to build a ported box inside the trunk but i don't really know where to begin....the box has to be 6.0 cubic feet after displacement and tuned between 28-30 hz. thanks

Hey Guys Call me a NOOB or Whatever you want, but i need your help, i have tried Kicker L7's, Pioneer Premier Spl, Alphasonik Mayhem and not really achieving alot , only the kicker sounded good but you only get one type of bass, now i want to set up a system thats gona be loud outside and shake the ground, i need your help here because i'm gonna try FI's should i get BL's or BTL's and should i go 2-12" or 1-15", i have a 09 sonata and currently have a MTX TE1501D amp but will upgrade to MMATS 3000.05 next month my trunk is huge but i still need cargo space, so i'm willing to sacrifice 36W x 17H x 19.5D, can you guys plz help me with a box plan also, i listen to mostly r…

I've got some complicated problems. Ok I'll just start with the maximum enclosure Size/Subwoofer Recommendations and we'll go from there. Anything marked with a * is a question/possible problem, please check these spots out. Woofer Recommends This: 2-2.5 Cubic Ft Per Woofer 50" Squared Port Area - 79" Squared Port Area Depending on Box Size. I would like to tune to 33 Hz I think that will sound good?* Enclosure Maximum size and WHY: 36" Exterior Width 30" Exterior Height 14" Exterior Depth Woofer Direction: Subwoofers mounted on top. Port Direction:* There is a door on one end of the enclosure and a seat on the other other end of the enclosure, there is a seat behind the …

Is there someone out there who can help me with a custom enclosure design with a single 10 inch jl audio 10w6v3. The enclosure i am looking for would need to be 1 cubic foot with aero ports tune at 35hz. As far as space i have to work with i draw a simple image of what the space i have to work with.

I recently bought 2 RE AUDIO SXX 12" woofers and plan to build the enclosure (vented) by myself (first time in my life). Since the manufactorer's web site only provides a box calculator for one woofer, can somebody kindly give me some advice on dual woofer enclosure and port measurement? In order for the box to fit in the trunck, the size constraints are: Length < 35", Height < 16.5". I prefer SQ over SPL and hope the bass hit as hard as they can. Thanks so much! The T/S parameters are listed below and more info. can be found on http://www.reaudio.com/woofers.php#goto_sxx Qes: 0.32 (Electrical Q value) Qms: 4.4 (Mechanical Q value) Qts: 0.30 (Total Speaker Q value)…

Well I've almost got enough saved up for a fully loaded 18" btl. I have a 2003 extended cab s10 this will be going in. My maximum dimensions are 23.5"(h) x 18"(w) x 50"(l). Those are outer dimensions. This will be powered by a Sundown Audio Saz-3000d into 1 ohm :bigclap: . I was wondering if 6 ft^3 would be fine with that much power with 80 in^2 of port tuned to 30 hz.

so i have just bought 4 ppi pcx 12'' subs and i need help building a box but im not good at all with knowing how big or long to make my port. i have a two door tahoe and i have plenty of space height 22'' width 46'' and length 37''. here are the specs each sub needs 1.25 cubic feet so 5 cubic feet all together. speaker displacement incuded is already included port diameter 2.6'' (inside) per sub port length 12'' per sub Equivalent Square Port 2.3x2.3 per sub if anyone could help that would be awesome i would also they the box to be around 30 hz's too

Hi guys new to the forum ,not new to car audio .I need help with my truck ,I want it to have slamming bass.The problem is not much room so I changed to buckets to allow for a console box. I have a t line with a sundown 6.5 and it is ok.I'm giving it 300rms but it's not doing what I want.I'm going to build a new box and have measurements of space for the new box. I'm planning on using a c.t sounds 900.1 amp for the new setup.The measurements are 10=h 32=l 9=w inches. Which box builder said 1.09 cubic feet ? I was thinking 2 8 soundqubed hs08, 2 D.C. 8s,sundown x-8 or ? Any help would be appreciated I planned on ported enclosure.

So i made a 4th order bandPass for 2 obsidian 12s out of birch. I started sanding the enclosure and filled it all the screw holes sanded all those spots with 60/120/220 grit sand paper everythings smooth(so i thought) i started painting the enclosure with kryole dual primer and paint(spray can) i thought it would be good to use that lol well im pretty stupid to think that was gonna work great. The corners are very dull along wIth the edges that are sanded and the top and sides are super shiny and it looks like shit. Whats a good paint to use to paint birch with and have it turn out super glossy. My goal is to have it very glossy and not be able to see with the edges meet …

i got a box that is 40x32x17 and trying to tune it to 32hz can someone help me find how big i need the port hole

I have a phoenix gold ti 12d and i'm wanting to build a 2.75 cu/ft SQ box tuned to 25hz. which are the specs. that site recommends for it. i have a mtx te 1501d that will be powering the sub in my 08 4dr toyota tacoma. i'm not the greatest with math and formulas so any help to make this buildup as painless as possible would be great. thank you

im looking if you have some photos of pvc tube with aeroport im looking forward to prove this on my car thanks i have some photos and i wanna see if you have som more for the experiment thanks something like this but i want to put 3 aeroport per pvc tube some smaller aeroport to check if this is better than sealed pvc ohh its for 15 RE XXX

there is no information on their site, anyone know where I could find the info or who to email? I want to put these in a box up against the incomming 4 Funky Pup 8s

i have i box that i need to find out what it's volume is and what it is tuned at. it is made of 3/4" mdf and has a double baffle. outside dimensions are: H 23 1/4" W 20" D 45" inside port dimensions are: H 5" W 18 1/2" D this i am not sure which measurement i need if i measure from the face of the port to the back wall it is 44 1/4" deep if i am to measure the length of the wall which divides the box to form the port it is 38 3/4" deep there is a 45% in the back of the port. thanks in advance for the help. would like to learn how to do these calculations also. perhaps if some one had the extra time i would love to see it drafted up into…