SPL & SQ / Fabrication

So basicly, box in trunk, 2 18's and 1 amp. for whatever db and iasca i guess, but for iasca i would have 2 amps

I built my box fits good....but the damn thing is to tall lol so i got to rip it aprt cut the rabbits and fix it pisses me off took 2 weeks to make and i fudgeed up but owell itsmy first box

Hey guys, I have been modeling different alignments for my Dayton RSS265-4 HO woofers. I like the look of 1.2-1.4 cu.ft after displacement for both of the tens, tuned around 30 hz. My question to you guys is how much port area I should shoot for? Would two 3" aeros be adequate? According to the modeling program, I would exceed 25m/s vent velocity using 2 3" aeros, but not by much. This install isn't meant to shatter spl records and each woofer will probably never see more than 300 watts, so taking this into account I don't really think I need such large port area. Looking for suggestions, Thanks

Hello, im building a box for a loaded 12 btl. i have an odd shaped box i made to fit under my silverado back seat. my question is how should i run my port/s. the box is wedge shaped with 3.6 cubes gross. the box dimentions are 11.25 high in front 8.5h in back 53.5 long and 16 deep. any idea on port location? trying to get 14 sq/in of port per cube seems hard. thanks steve height1 11.25" height 2 8.5" length 53.5" depth 16" the sub will be facing up on the drivers side

i'm thinking about making a box for my trans am to these specs, but i dont know if its going to be big enough for my rl-p's. i know it should be simple, but i've tried for hours and can't figure this out for myself. could someone please tell me how many cubic feet per side i'm going to get out of this box if i build it? i would REALLY appreciate it. http://thirdgen.org/techbb2/showthread.php...threadid=306257

After doing the math i come up with a .825 cubic foot enclosure which doesn't seem to leave me with room for ports. Can someone help me out here please? What should my internal volume be? I used the box calculator at the12volt.com, is there a different calculator I should be using? Thank You to anyone who can help me.

what tunning should i use for my box , i need it for LSQ should i do, 25-30-35 or 40 ??

If i where planning on useing external ports for my SPL set up (probably a pair of 6") to decrease cancelation and turbulance would it still be a good idea toconjure up some type of brace for the port? i would assume so but im not 100% sure. Keep in mind i want to easily be able to change the length of the port not only for trial and error testing to get the highest score but also so i can give it a daily tuning for the ride too and from the competitions and so i dont have to lug the Ava out of and into my truck every other weekend.

Hello all! I am looking to reconfigure my trunk set-up in my Mazda 3 and am looking for some feedback on my idea to see if this would give me my desired result. Currently, I have the subwoofer firing straight to the back of the car, with the port opened up to the rear deck ( I use a flared round port). The problem is that the rear deck is completely solid and this causes quite a bit of rattling, even after deadening the whole trunk. What I am considering doing is rebuilding the box to have the sub firing straight to the back of the car, with the port opened up on the back of the box. In order to do this, I would need to put an elbow on the PVC port because the box will…

Im an authorized Soundstream dealer and MECP certified installer. I do all sorts of installs from cdplayers to custom fabrication. If you have any quesitons please feel free to let me know. I would be glad to help in any way. Mike

Sorry for another question (just taking advantage of my day off). I just finished up damping my door panels, the sheet metal, framing, and plastic panels,as well as the rear hatch with eDead 120 and Damplifier Pro. Probably have used about >80 ft^3 so far. I am doing my entire roof and going to do the floor soon too but I am having trouble deciding what to do next. I keep reading very different theories about what to do, whether to use closed cell foams or open cell foams and where to use them. Some of you have recommended websites to buy different products but just need to know how much and what to buy. I have a lot of room in my doors between the interior plast…

Does port/woofer aiming really matter that much in an SUV? I'm looking at placing the box in the passenger rear corner with the woofer firing cross cabin and port forward.

I am planning a box design in which I am using two 3" aero ports. The ports are supposed to be 7 inches long. My question is when using aero ports does the actual tube have to be seven inches or does the entire port assembly (flares included) need to be 7 inches?

Hi guys, I will be building the pre cut enclosures I calculated under RE enclosure calculator but there are a few things I would like to verify. I would like to tune the box between 33-35Hz @ 1.8-2.0 cubic ft. However, I just read that the RE calculator is not accurate. So I searched and found this website Enclosure Volume Calculator (EVC) and made the following calculations: Box Width 23 Inches Box Height 15 Inches Box Depth 15 Inches Material Thickness 0.75 Inches Number of Drivers 1 Total Total Port Volume 258.188 Inches3 -----> see calculations below: Port Width 13.5 Inches Port Height 1.5 Inches Port Depth 12.5 Inches Driver Volume …

Hi folks. I just picked up a pair of L7 10's to go in my single cab 06 Sierra. I would like to go ported if I can make it play loud and hard enough over a sealed setup to be worth while, however I am not sure as to what my best bet would be in terms of porting for this. The enclosure dimentions will be18"Hx57"Wx7D which is good for 2.91 cubes if my math is right. I've been running 1 12" powerbass L12 in a 2 cubic ft ported enclosure with the sub behind the pasenger seat and one 4" port firing up from the top on the oposite end and it has sounded pretty decent, but I want to run more power and get louder and due to mounting depth issues a more substantial higher power ha…

i just had my wood cut from lowes (they did a bad job cutting) and i was wonder what size screws should i use to put the together? i dont have a router so what else could i use to cut the hole out for my sub? i have some titebond wood glue and some heavy duty liquid nails here.

how does it measure the frequncy of the port if it does not know the displacement of the sub?

I Recently Talked to Chad Kyupers Drivers Start Shipping a week from today. While talking to him i mentioned 6cuft@29Hz, he said he had a guy do 4.5 at 30Hz and its output was INSANE with only 800w. he said 6@29 with 1200w should wang hard so im down to 2 enclosure options, both with equal port area (77sqin) only one iwth 2 ports and one with one. originally i though there was going to be no way to get the ports on the same plain as the driver, so i designed a side firing enclosure and the port a straight shot. then i came up with the idea to get the port on the same plain... see image below http://i11.photobucket.com/albums/a167/CBFryman2/avatest.bmp the bottom thing…

Do I have a 12 Xcon and I was wondering the best sub an port placement.

Just checking pricing on various different places. What places do you guys use for your resin/matte/cloth?

I have talked with rob and rusty from dc on everything to do with my upcoming design for summer 2012. I am going to go with 2 xl 12s on two SAZ-3500Ds, backed up with juicebox batteries and a 220amp excessive amperage alt. The box will be a little smaller than recommended seeing as DCs love smaller boxes when they are overpowered. Now my question for everybody that I cant seem to get a hold of is port area, would I be better off giving it a little more (Kerf port btw) space (say 18-20sqin per cuft) or the "normal" range of 15-18sqiin per cuft? My goal is to get decent numbers in the low 30s. I do not have the depth either for aeroports. A 5" aero though would be 21 sqin p…

Just a for instance: Say you have an enclosure 40" wide x 32" long x 30" high, The port is 38.5" wide (facing forward), 6.5" in height, and 24.5" in length - tuned to approximately 34Hz (I'm assuming a driver XMax of 20mm.) The Net enclosure volume is 14.40 cubes, less driver displacement. You have the option of placing (4) 15" subs on the top baffle, or (9) 10" subs. Which do YOU choose, and why? What subs would YOU do? Roughly 1.5 cubes each for the 10's, or 3.37 for the 15's. Either way, it would be possible to run whatever amp at 1 ohm Mono - Strapped SAZ3500's, anyone? I'd be VERY interested to see/hear/speculate what the XCONS would do......

I was wondering if I could use metal L brackets in the inside or outside the sub box the reduce the vibration or flex? I saw the wood ones, but those take space inside the box and my box is quite small and I don't wanted any more smaller.

Stupidly I bought an 18 Fi BL and didn't realize I couldn't fit the recommended box inside my trunk...its anywhere between 4-4.5 cubic ft..Is there anyway I can build a new box similar in size that will increase the current SPL levels and help not suffocate the sub-woofer so much?

http://www.partsexpress.com/pe/pshowdetl.c...=25&rak=390-802