SPL & SQ / Fabrication

I'm just looking for some pointers on where I could look for reputable information on designing 2 way passive, 2 way active and (after some practice) eventually 3 way active front stages. Just stuff like, what to keep in mind as far as driver selection, particular features to look for when choosing a certain driver, and how to design passive crossovers. I was daydreaming and hit a roadblock when I realized, what the hell do I even know about a quality front stage? I can't say much at all, other than, deaden, and airseal the speakers. So I feel like it's time to start learning, might even have some applicable tips on hand for when the new truck is ready I'm plannin…

I am looking at some new midbass drivers and it looks that they should be ported. So if and when I build this enclosure in/on my door is there a recommendation on where to point the port in this application? thanks in advance.

I'm thinking about building a new box for my 15" DC level 3. My current box is slot ported to the back with the sub firing up towards the trunk lid, 3.3^ft tuned to 32 hz. I was thinking about building a box firing into the cab (BMW 330CI). Im not too experienced with building boxes but think i can manage this. Has anyone here done this kind of box before and can give me any pointers?

Long story short my friend built my box and it turned out horrible it wasent his fault he did not have enough tools or supplies but I'm getting a shop to build me a new one and I have an original design but its to wide but I can add to the height my dimensions are 22 deep 33 high 55 wide the box design is 27 high 27 deep and 54 wide wouldn't the volume even out if I went 32 high and 22 deep?

So I am designing a new enclosure and this one will have a center port. I have concerns with my port width when it reaches the rear of the enclosure. This is for 2-Zcon 12's,SAZ3500 power,currently box will be at a net volume roughly 7.8 cubes tuned at 32 the distance from the port wall to the flare is 4.33 inches if you cant read the photo Since it is in the center do I need to maintain the same width(in my case 6.5inches)? Is there a rule of thumb for this? Here is a pic of what I currently have designed.

Does anyone know what the tuning is of the dual X15 box sundown recomends? And how many cubic ft it is?

Looking for someone to help me design an enclosure with a kerfed port. I have been trying out doing it on scrap wood in my garage for a while and wanting to try it out on one of my enclosures. I have someone wanting an enclosure built right now and figured it would be a good one to start with. Its for 2 sundown sa8v2's in a trunk . I was told there Going to be on 1-1500 rms. . .Max dimensions - 30 wide 10 tall and 16 deep. (Ill ask if any of the dimensions can get bigger) Wanting it subs facing up and port back. Tuned in the low 30s. 30-34. . . . . Listens to mostly rap music.

Have a 12" icon showing up soon and would like to get an enclosure ready for it. I've been using the bitpusher site to help me calculate the box. This is what I have so far Now I prefer to use a Single 4" precision port. I'm unsure how to calculate the entire port area I have with this setup. Reading through past threads and SSA's recommended 2.25 cu ft tuned in the low 30s. Also saw in a thread that for that size box I should aim for around 35 sq in of port. Pi * r * r doesn't calculate the length? Missing something somewhere maybe someone can help. Is a single 4" aero going to give me enough port area? Anything you see wrong here? One other thing. Going off the picture…

I have been messing around with WINISD for the past day or so. Trying to model my 12" Zcons and follow what these graphs are telling me. 1. When I enter the parameters using the autofill for some of them my graph peaks at around 100hz even though my box tuning is much lower. Why is this?Can someone help this NEWB to understand what I have done in error. 2. Also if I enter the paramters of the web site it gives me error messages saying they are incorrect. If I let it autofill some of them then it will graph. Any explanantion why this is? Thanks in advance.

I built a sealed box for my 12" ICON to proper size for my mustang, but I've recently sold that car and picked up a small hatchback. I want to stick with the sealed enclosure design for this car to minimize the amount of space. Whats the smallest I could go enclosure-wise for the ICON? Would it be possible to go smaller than the .9-1.25cu ft size thats recommended if the difference way made up with polyfill? Ideally i want as small as box as possible but I still want the sub to sound great.

i have a 96 sonoma king cab i need help designing a ported box tuned in the 30s to kill lows if some one could help i just need a blue print to biuld off of

Hey all. I've been riding with the ICON sealed for some time and want to put it in a ported box. Really not sure how to make sure the design is correct or even how to work WinISD but below is what I've gathered. I was posting on diymobile and got some help and was suggested a ported box, 2.0ft^3 @ 30hz will give the flattest response. Below is a copy paste from the sticky of "making a correct box design thread" Vehicle : 08 Acura TL Location in the vehicle: Trunk Space available (Length x Width x Height): 23x19x14 (Can be wider and deeper than height) Subwoofer make and model: SSA ICON Subwoofer Size: 12" Number of Subwoofers: 1 Type of Port (Kerfed, Slot, Aero, etc.…

As I begin my adventure in the SQ lanes, I have been doing a lot of research and studying. My general synopsis is, for SPL, in a vehicle, we want the most reflective material possible, such a concrete, or marble, so that there is no loss in energy. Obviously this is not practical, but in this example, it will work. Ok, and for SQ, we want the total opposite, we want complete absorption so that none of the higher frequencies reflect, which can cause interference, overlap, and many other issues. From what I've seen, things such as egg carts, foam, or MLV would be the fix. So what I am asking, what would be the best and most particle material to use in the vehicle for sou…

I am using a audiocontrol 3055 to tune my system once its parts arrive. I like the kicker KQ30 but it has 1 in and 1 out for RCA. this would make me think i need to have amps with pass through. if i am outputting a 0.2V signal from my HU to my KQ30 and a 8V out of the KQ to amp 1, 2, 3, 4, and 5 would amp 5 have a 2V signal or a 8V signal? how many amps can i daisy chain in this manor before i run into issues. secondly i have a KX3 that i do not believe i will need but if i end up using it would i run into a SQ issue having HU > EQ > Xover > amp? would that added processor cause issues with sound quality? a third question is if i am to have all my amps/proces…

Do you guys think an 8" aero port would be enough port area for 2 12" zcons? They would be in about 6 cubic feet after displacements. On around 3500 rms. Tuned around 34hz. I want to go with a 10" port but an 8" would be a lot easier since I'm only going to have about 36" for the width. You think I should test it out and try or do you thinks its forsure not enough?

My 12" ICON is coming in the mail today so I want to finalize a design before before having my buddy build it for me. What I want to know is if I have calculated everything correctly and will in fact end up with 2.3ft^3 at 32.5hz. Here's how I measured the port length. 19.2140 + 14.8723 + 1.375 = 35.312 The the12volt calculator says that this length gives me about 32.5hz. Did I design this correctly? Also, I just used the displacement listed on the product page which is .16. Does doing a double baffle affect this? Click here if you want to download my SketchUp design

This is a WINisd plot of my final 3. It is comparing 3 ETHOS 12's against an EVIL 18 and a pair of ETHOS 15's. The ETHOS enclosures were taken directly from some of Quentin's suggestions, and the EVIL 18 was a shot in the dark based on my space limitations. How accurate is WINisd in calculating real world SPL? Based on the modeling an EVIL 18 equals three ETHOS 12's at peak tuning (hard to believe); the ETHOS 15's win all...The EVIL 18 is pitted against the three ETHOS 12's for SB2 class reasons, the pair of ETHOS 15's is for I don't give a damn what class I compete in reasons.

Hey guys, I have my second Xcon and needing new enclosure but have been debating staying ported or going back to sealed (save cargo space) Anyway, I am first time user of Winisd and not sure if I did this correct so could someone let me know if it looks ok? How do you interpret this graph? To me it looks like ported is the way to go. (I modeled using two 15" Xcons at 1000rms each) Let me know if you need any additional info about my setup...believe my SUV cabin gain peaks @ 49 Hz.

What all do I need to model my zcon for the new enclosure? About to start building and want to have the enclosure design as good as I can.

Hello, this weekend I hope to construct a center console for my truck. The vehicle is a 99 ram 1500 quad cab The box will take place of the center bottom seat cushion, allowing the top flip up portion to still be utilized as storage. The box will house 2 FI Q10 D2 subs with everything but high qts option The box dimensions are H:10" W:15" L:30" Box material will be 1/2 birch ply home depot project panels Box gross volume is 2.11 Port will be precision port dimpled inner + outer flare 4" diameter 24 inches long for a net volume of 1.67 cuft and port tuning frequency of 27.43Hz according to torres. Box will have flame kissed woodgrain with a very dark cherry stain and s…

Let me start out by saying that I have been out of the car audio game for some time, and I have never been as concerned with SPL as much as I have been with overall sound quality. It has been a mystery to me for some time as to why no one uses high efficiency subwoofers: for example a pro audio subwoofer. If the main concern is to get loud, why is this option never mentioned or even discussed. Many car audio subwoofers I see are in the range of 85-90 dB at 1 watt measured at 1 meter. Maybe closer to low 90s for a large woofer. On the other hand, many pro audio speakers have much higher efficiency, 95dB+ for 1 watt at 1 meter. To me it seems that efficiency would be…

When you build a box with a swapable port, how to you determine internal box volume, as in, what it needs to be once the port is in? I'm going to build a box for the BTL that's 7.5 cubes and want three different ports, 26hz, 34hz, and one for whatever my peak frequency in the vehicle with be. I'm not sure, but wouldn't the different port sizes also affect tuning by changing box volume? I feel like this is really simple and i'm just punching myself in the face here. What am I missing?

So I keep getting told that an active front stage can be and usually is better than a passive component setup. Now, doing the front stage is very new to me. I've really only done a co-axial set powered by a 2 channel amp. I'm going to need some help with speaker selection and ways/tricks to make sure everything is installed/tuned correctly. To put a number on a budget, I would say $400. That number is just what I have set aside for the front stage currently. Sound deadening is not included with that budget. This is going into a 2014 Fusion. I don't want to cut any holes in panels and I can't fiberglass so stock locations will be used. Which is a 6.5 and tweeter. I will b…

I ordered 2 18 zcons Thursday and today I did some measurements and got 48w 25h 32d all inches and that's with my back seat out of my ext cab sierra I listen to mainly rap with a little bit of everything I was thinking around 32 htz for tuning there going to be on a saz 5000 I'm sorry if I forgot to add anything

About to start the new enclosure for my 2 zcon 12s. It will be a trunk wall. I will be trying a 10 inch round port this time. I'm wondering how many cubic feet you guys think I should aim for with the new enclosure? ? Will have an aq3500 at .5 on them but Will be adding another 3500 as soon as I can find another. . Going to be tuning around 33-34. any suggestions?