Build Logs

Car: 96 Honda Accord 2 door Subs: two 10" SSD subs bp options and copper coils Amp: IA20.1 Rear battery: Deka 9a31 Box: 3 cubes net daily tuned to 34.3hz / competition tuned to 44.66hz The front baffle will be facing the back seats and the port will be facing the driver side.

I did this install last summer. I know everyone likes to look at pics, so I posted up this build for entertainment. Parts List: 2 ~ 4x6" dash plate Infinity Kappa 2 ~ 6-1/2" Door Infinity Kappa 3-way 2 ~ 1" Infinity Kappa Tweets 2 ~ 6x9" Infinity Kappa 3-way 4 ~ T115D2 Rockford Fosgate Power 2 ~ T1500-1bd Rockford Fosgate Power (Powering the subs) 1 ~ T600-4 Rockford Fosgate Power (mids and highs) 1 ~ Stinger SP1700 battery Jensen VM9312HD Flip out DVD H/U Iraggi 300 amp H/O alternator All Stinger wire and terminals Installed by yours truely!

This is a build for Traveling Bass in a Convertible Mustang Top Down :spiteful: (Yes it can be done) This Build Was Done By Andy From VexProductions.com Heres what went into this project Speakers 4- 10" FI BL's 4- 8" O2's 2- 6.5" Beyma 6MI 4- Soundstream Tweeters Ampiflers 1 - T4000.1 Fosgate 3 - T500.2 Fosgate's 1

just a little box I built last night with some assistance from Ernie. Truck: Regular Cab 2005 Dodge Ram 6.094ft^3 @33hz

Here

Well I've started the Ram finally. The tranny is about toast, but I'll deal with that when she gives up. So far I'm just started on wiring. I gutted it and started the wiring yesterday--and cleaned the moldy carpet (door seals are bad and getting replaced)... only about 3 hours invested so far. I didn't do before pics, really didn't think about it. here's some deadener. All I did is replace what was bad of the factory deadener. I have no intent on keeping this truck so I don't care to go all out on it. the factory deadener was crumbling from the excessive water that's been on the floor board. this is about all the deadener you need on the back to keep it from hu…

I received a phone call last night at work from a friend who I have not seen in several months. He moved for our company to start up a new facility. He has done may wild builds in the past some of which I ask him to post. He recently started an account here and ask me to start his build log. So far he has purchased: 8 Kicker cvr 15"s 2 Hifonics XXV Colossus amps Audio Control Epic-160 4 sets of Kicker ds650.2 Deka batteries (not sure of size) He is going to putting this in a Ford minivan and is currently planning on going with a sealed sub enclosure. I am sure that I have forgotten something, but once his membership is approved he will set the build straight. He is inte…

I just got done with a temp box, http://www.soundsolutionsaudio.com/forum/i...showtopic=27944 Now Im gonna start a build log of the rest of my car. hopefully ill finish it this summer. Right now im starting of with new door panels. each door will have 2 7in daytons and 1 morel tweeter. Started off with doorpanels for a junkyard cut of parts i didnt want Put some cloth to flatten out the basic shape now to mount the baffle before sandin, i played it baby poweder...prevents the itchin Delivery today!! Ring terminals I even got a sticker this time and another delivery the same day Tweeters and switches now to start on the tweeters deaden t…

Heres a little job i started over the weekend 2 18s .. he had 2 memphis 4ks, but they are sold so im not sure what this things going to get... i got a late start on the pics.

When i first got it. now.... vid http://www.youtube.com/watch?v=fR3Gknf6snE Fi Q 12" D2 Audiopipe AP-15001D @ 1ohm Scosche wiring It gets a little hard to breathe after a minute or so. Still working on the install a little bit.... Not driving everyday as of now due to no permit (doesn't look like I'll be getting it soon ftl)

What is the best way to fix rattles in my vehicle. I have a Tahoe and pushing 1100W over 2 12" IA's ,rattle problems are in door panels and mostly headliner(specifically the temp. control unit in rear headliner) Anyone w/ a Tahoe that knows exactly what I'm talking about please respond.

A Kenwood KDC-MP538U deck is going to be installed. Knu 4 gauge wires and the BIG 3 will be done in 4 gauge as well. Stock speakers are going to be kept. Sub box is 2.5 cubes net tuned to 32hz. User will be playing all types of music and this is for a daily set-up.

So me and Jake met up today with Edgar in San Marcos to give him his custom made enclosure that he ordered from us made for 2 18 bls. Too big for our cars to carry so we had to take the tahoe I even gave it my signature blessing for maximum spl. Jake liked it so much he wanted to live in the dammed thing. The box came out really nice; ready for vynil, carpet, rhinoliner, you name it! Here are some pics. pix whatever you kids call them these days. Thanks again Edgar!

time to start this since i got everything ordered. gear this time around: Deck-Kenwood DDX6019 Speakers: CDT CL-61is Speaker Amp: JBL 75.4(bridged) Subs: Evo SPL 15s Sub Amp: RF T3k(til it sells) Deadener: Second Skin Damp Wiring: Kicker & Stinger(missing somethin else) Batts: Stock(for now), PM D3100(getting another soon) Alt: Stock 160amp pics of car:

Still need to add some corner pieces, only just added port corner piece yesterday after using the box for 2 months now lol...lazy:

I decided to build a kind of fart box for a local comp to get higher scores. and while i was designing it i thought i could make a second port for daily use and shove it through my backseat. I wanted to get a box for two 15s in the car but the most space i could get with the design i had in mind was 2.375 cubes per sub and i want more. so ill be using this box for this month then work out a new design based on this new box to get 2 15s in my trunk. this box will be a little over 4 cubes, with an external flared port, and lots of threaded rod and carriage bolts. i spent most of the day getting this far

For a single AQ HDC3-A 10" 1.5@37hz Dual flare. Flush. On with the pics.

Just finished the box for my BL 12. It's going behind the rear seat, too bad no one will see it!

Here are pics of "Moms Soccer Van" before it goes in for custom vinyl graphics. Rear windows have been blacked out and urethane sealed To prevent flexing. Passive crossovers flushed into the passenger side under seat drawer. Refer all questions to 02skidoo as I only assisted on the dampening and tweeter install and brainstorming. Brian did all the rest himself. All dampening is Rockford Fosgate Deadskin (1 layer roof and sidewalls) Alt is from Ohio Generator and 3 Kinetik's. Could use a couple more. Now all I need to do is talk the Owner into Sundown and others!

This box is a rebuild due to his last box apparently never being built correctly. A 15yr old guy on ca.com that seems to do decent work built his last box, but it was rattling from day one and Ben thought it was the sub, and I, telling him the whole time it sounded like either his hatch or the box. Either way, the top plate of the box seperated from the enclosure walls and really rattled, making this setup un-playable. So we decided to build him a new one. Ernie started this box yesterday and we finished it up today. old box. new box. we'll have to get some video's of this thing now. It flexs everything in his car, digs down nice and low and distorts my voice e…

This is a joint venture between Evolution Parts, Mach 5 and local fabricator who does awesome work - Hamilton Audio. As per statements made by the owner of Hamilton Audio (Brian): Vehicle - Astro Van Subwoofers - Mach 5 Audio Amplifiers - SounDigital Front end - Beyma Power distribution - Tsunami and ProLink Class - 159.9 Bass Racer and ???? straight fart cannon Box design - wait and see More info to follow...

I know these are just a few and baaaaad pictures, but i wanna show you what im very proud of... This is the thing the enclosure is made of, a stock part of the car which is in the trunk. Finished (fibreglassed and mdf baffle)... Installed Its 1.4 cuft after displacements tuned to 36 hz.... Sound really nice and because the enclosure is screwed in the cars chassis everthing vibrates Its complete stealth after the orginal plate is over the sub.. I know my language sucks but i hope you understand and see whats done faezich And one last question: Looking for someone who can do blueprints for an spl comp. enclosure (flared port?!?) for my spl car ...?

This is the lawn mower I built for a Crutchfield Dream It contest. W7-8, PDX 600 and 150, Pioneer 7000bt, and polk mm 6 3/4s. Optima yellow top 4 gauge wire fused distribution. And street glow Check it out tell me what you like. Its on crutchfield too Also video of build and install.

Im a rookie and this is the first time i've bent MDF. I think I did an alright job, I'm just curious as to what kind of feedback id get from this.

Took advantage of some free time and the nice weather to get started on my box for the DLS sub. let's get some wood cut eh? pieces all cut out and ready for assembly one more piece to go! ready to start marking and cutting out the hole for the flared port opening. the port on the inside. excuse the huge glare from the sun :\ covering the mounting area so the spray won't get on it. a peek inside through the port opening. lots of clearance between the motor and port tune. done! it's 1.62 cubic feet ported and tuned to 35Hz. i haven't installed it into the car yet...ran out of daylight and the mosquitos are out in full force. i'll get it into the car as s…