Amplifiers / Head Units / Processors / Electrical

Hi can anyone help, I have a kicker sx900x2 amp which drives one L7 15" sub what is the best amp setting I could used to achive the best result? ray

Looking at a setup for my car inolving 2 12" l7's, Is the 1200.1 SX amp a perfect match for the two of them wired down to 1 ohm???

my setup will be a 3way setup for my front stage consisting of; 8"(undecided) in doors 4" CDT gold 2way set in kicks 12" iCONs in trunk HU is kenwood DDX7017 (somethin like that) amps will all be kicker(undecided on models) so my question is; is the KX3 3-way active crossover from kicker a good option? if not what would be better? im debating on also putting a set of some 6.5 midbass drivers in the panel next to my door for a bit of rear fill, i know its not most peoples taste, but my 3way setup is worrying me about missing some fill. if i decided to use those rears would u just use the 2way crossover as well as the 3way for the front? is there anything im missing? thank…

Ok, I just got this amp from a friend, I was unaware I needed a 300 amp fuse for it, but I hooked it up anyway without one. It works fine without the fuse, but Kicker plainly states it needs the 300 amp fuse. So, I go to a local shop and buy the Kicker fuse holder and a 250 amp anl fuse, they did not have 300 amp fuses so I figured 250 was better than nothing. Also, Kicker recommends 1 gauge minimum, I have 2 gauge power and ground in the car now, I plan to upgrade ALL wire to 1 gauge, but my question is, will the 2 guage hurt the amp while I am scrounging money for wire? I noticed that the right side of the amp gets hot, the Kx lines are supposed to have fans in them so …

do you think that a kicker kx600.4 amp will work for a pair of 12 cvrs. do you think it will sound good. thx

what would you guys pay for a good working Kicker KX 800.2 thanx

I was looking at getting the Kicker KX3 Crossover to let me run active. I'll have a pair of Ascendant Audio Carbon Fiber Mids and a set of Morel tweeters. A 4 Channel will be powering the speakers. If I wire the tweets on the front channels and mids on the rear channels, should I be all set? I'll obviously bandpass the mids, and just use the HPF on the tweets. Ive read the manual, but the controls are odd. I looked into the AudioControl 4XS, but this is cheaper new. Thanks for the help

which one would u pick. well i have a mtx 1501d with stock everything right but this amp is power hungry. i'm looking to get the kicker ZX1000.1 and mayb it will be less stressful on my electrical system. 1. mtx 1501d 2. kicker zx100.1 3. crunch ground pounder 2500d

what would be a god amp to run it?

Alright, I need to go 4-way active with 2 sets bandpassed... I thought my only option was to run a crossover, I didn't realize the SX Kicker amps are bandpassable on every channel? So I can run 2 SX900.4 with the remote instead?!?! Please help! Thank you! Jordan Crossovers 10Hz – 16kHz variable HP frequency adjustable in 1/12th octave steps 30Hz – 20kHz variable LP frequency adjustable in 1/12th octave steps 6 – 36dB/octave variable crossover slopes (up to 48dB/octave on the 650.1) HP, BP, and LP on every channel http://www.diymobileaudio.com/forum/member-product-reviews/6375-running-active-setup-using-kicker-sx-amps-dsp.html

anyone have experience with these? I was thinking about getting a 400.2 or 500.2 to power to power my front stage(once i can decide on a set) because they look like they have a lot of features for the money. Anyone know anything about these amps?

Just bought a pair of Kicker SX900.4 amps from HiFi Connection for under $300 each (through their ebay link). Nice 4 channel amp for that price and they are an authorized dealer! Brian

I was just browsing the wooferetc website and I found that they are having a really great deal on the kicker war horse amp... http://www.woofersetc.com/p-6814-warhorse-wx100001-kicker-1-ch-20000-watt-amplifier.aspx seems like a really great price for 10k watts. Just throwing it out there for you guys that want a lot of power.

Can get a great deal on one and was trying to get some Specifications. http://www.carsound.com/reviews/amps/zr360.html http://www.crutchfield.com/S-nvAPS3E4lWG/c...;i=206ZR360#Tab http://www.kicker.com/06/tech-support/manu...s/ZRAmpsMan.pdf I know that this is a cheater amp but dose any one have any experience with this amp or any one who has ?

I have two dual 1 ohm 18 BTLs fully loaded in a single chamber box...12 cubic feet after subs and port...with two kicker 2500.1...my gain was all the way down...my bass boost on the amps was half way up with the bass on my head unit at zero...when ever I turn my remote bass up the amps starts clipping...I had two MTX 8500 12s that hit louder on the local meter...I have a 275 amp alternator with another one on the way with two red top optimas all zero gauge wires power and ground wires...can someone help me out...I know these amps are better then this...

has any 1 Sean a berth sheet from a zx1000.1 what was its top rms and @ how many volt's. And are they 1ohm stable

the kicker zx1000.1 has a 0-18db variable bass boost at 40hz.. my question is if i want to run my IDQ15s ported and tuned to 28-30hz would the bass boost hurt the sound of the subs?

This may be a stupid question, but i want to be sure before i go and buy this. I want to run this amp(kicker zx200.4) for only one component set. I could just bridge it so it does 100 watts x2 at 4 ohms, right? or is bridging a 4 channel to a two channel not a good idea? thanks

I am getting 2 15" AA havocs (hence the name lmao!) 1250 watts rms per sub ... i have noticed that they are going to have to be dvc 2 ohm per sub (no other options for ohms)... My question is which amp would be better to power these subs... i kno alot of responses will be sundown... and i am leaning toward sundown but thinking realistically i could wire the sundown to 2 ohms and get 1600 watts split between 2 subs or i could go with the kicker and get 2500 split between subs... i really want the sundown but i dont want to underpower the subs... i am stuck and getting indecisive... which would be the better buy...

i was thinkin i wanted to get a 3000-3500 watt amp for 2 15" BL's but i just thought to myself that im not goin to compete with them, so is having the extra 250-450 watts really worth it??

just got my amp. in the box it came with a paper that says "Total Maximum Power Output: 930 watts." can anyone explain what exactly this means? like is it at 2 ohms at a certain voltage or is it the 2 ohm and 4 ohm ratings total added? or what? thanks!

Are these amps underrated? Anybody have a birth sheet or a estimate of what the 750.1 will really do @2ohms?

Used Birthsheet 2960rms $375 shipped is the price what do u guys think?

Got this e-mailed to me today. It is a great deal. Not sure about the quality. But for 300 bucks. it is worth looking at. http://www.partsexpress.com/pe/pshowdetl.c...tnumber=263-950 Later, 2003blkhemi I do not represent phoenix gold or parts express in any way. Just passing along a good deal.

So i want to upgrade. But not immediately. like. May not upgrade for a whiiile. But have chance to get a bigger amp. so total hypothetical. I currently have an AQ1200 in my truck with full 4 gauge wires off stock alt and batt. could I, run an 2k amp off of this set up. Never goin over like, probably quarter gain to half. (prollly long time before that amp would clip) 2k amp being a db drive okur 2k. I know anything above 1.5k comes with 1/0 inputs. But could i run it off of the 4 gauge til i can upgrade the rest of the set up is my basic question. Any of your guys' vast knowledge would be great!! thanks in advance!