Amplifiers / Head Units / Processors / Electrical

I am about to start building my system in my ex cab toyota truck. I am not sure if I am going with 2 Fi Q15's or 2 BL15's, fully loaded yet. But I need a amp that puts out around 1000 watts RMS at 1 ohm for around $360. So far I have been looking at these: Hifonics 2600W for around $350 AudioQue AQ2200D for $390 Which one of these should I get or is there any other amp out there in this price range that might be better?

alright, I have 4 guage wiring right now, not installed. and there is some 1/0 on here I was considering buying, but if I dont need it then why spend more money. I am going to do the big 3 in 4 gauge, there will be a run of probably 8+ feet to a D block under my seat where a 4ch amp will sit. it will enter a D block, and leave as 8 gauge to the 2ch. another run of 4 will leave the D block and make a trip of about 6+ feet to the sub amp behind the rear seat. I am going to set the gain on the sub amp at 800 watts, and not sure whats happening with the front stage, but worst case scenario - rear channels will be 100x2 and fronts 75x2. so Ill be pushing 1150 watts at the mos…

Well I have ran into something here and I think I may have gotten lucky on my part.... My friend who is going to help me install my car system here whenever I get everything together. He told me that he has a 5 farad cap and that I could have it from him for a few cases of...beverages. Now I am curious about this seeing as I was told to stay away from caps and just get a battery bank. What questions should I ask him when deciding if I want this or not? He says its pretty new and was only installed into his car system once. Then he took it out due to too many tickets over a week (must have been dumb about it) and never put it back in. Now for the serious question here, sho…

Hmm, how do you figure out what fuses to run for inline power and distributor block? Right now they are matched with the amps, but they should be matched with the wire, right? Here's what I have now: Soundstream TRX1500D (120A) Soundstream TRX2.550 (60A) Inline Fuse = 250A Distribution block = 60A & 120A Power wiring is all 1/0 except after distribution block (2x4AWG) Question is for next year, I'm doing some upgrades: Soundstream RUB1.2500D (250A) Sounstream RUB2.600 (60A) Wiring will remain the same except I'll be running 1/0AWG from the block to the 1.2500D What fuses should I choose? Do I need to upgrade anything else? Alternator is 200A. Lemme know if you see som…

when puting the fuses back in my amp i broke the thing that holds the fuse. so right now i am just running a lead (with a fuse in it) from the holder thats not broken to the power 12v on the amp. will this be ok to keep this way. or is it wasy to just heat up the solder and put a new holder in and where can i get one. could i get a in line fuse holder and run from one lead to another and solder them in. i cant run just one amp.. there in a common camber box all 4.

hey whats up im looking for a huge battery for my secondary battery something that can handle burps really well and a lil music here and there what are the differences between these two and which ones better thanks

I have a Fi BL 15 and im trying to figure out whats better the Terminator 4000d or the saz 1500d? the terminator is cheaper, is the quality good? which one is easier on the electrical system? Cleaner sound? thanks

Ok i have a audiopipe ap3002 and the it stoped working and now the power light is flashing. is it toast or can i fix it??????

So i was taking out the radio on my bosses truck and this is what i find..... ] That's one for GM, Chevy, Ford, Nissan, and VW lol

Will this amp work alright for a single p3 sub. Just had it given to me HELP!!!!!!!!!!!!!!

Crunch Powerzone P 900.4 4-Channel Amplification 900W 2 / 3 / 4-Channel A/B Class Amplifier 115W x 4-Ch @ 4-Ohms or 225W x 4-Ch @ 2-Ohms or 450W x 2-Ch @ 4-Ohms Dynamic Music Watts we have this and (2) IA 187 12"s ..... dual 4ohm. what do i need to do to wire the two subs in order to get the most out of this amp? thanks Chop

Have a guy that wants to trade me a pair of modified Stetsom 2K6D's for my pair of SoundStream 6500D's. the 2K6D's are modded and he has run them down to almost .25ohm before. He says at nationals last year, he strapped them and ran them on a 1.4DVC subwoofer and got over 9Kw out of the pair...? I hear they are pretty under rated but I have no personal experience, I know the 6500D clamped just over 4200 @ 1ohm on 13.8v~... EDIT: These are the older Stetsoms, not the newer "Vulcan" ones... what are your thoughts?

Ok I was told the Sundown 4500D is a bad amp because the 86% eff @ 4ohms at 100Hz, so I was told to look into the HellFire 2500.1, the MTX TA92001, and the T1500-1bd. I am going to be getting 2 12" BTLs, fully loaded daily drivers. Anyone have any words of wisdom?

Hey everyone, Got a question. Are Power Acoustik amps any good? One on dealer cost car audio pretty cheap. Opinions please....

I have had one of these guys sitting around in my room for a while now. The only info I've ever really found was this thread from 2006. Anybody have any other info?

ok so i got a new HU and i connected everything according to what i know. my HU is a jvc kd-g820 when i plug the wires to the HU it makes a noise that you can hear is working then it stops but when i try to turn on nothing happens. my question is do i have to connect the illumination wire to the orange or to the 12v which is yellow ? since nothing happens when press any buttons

I was looking at Powerbastard's alternators, and they don't have a direct fit for my 1991 Acura Integra....but.... they link me directly to the Fitzall 220+ Alt.... basically it's a universal HO alternator for imports..... I was looking at it, and the bottom foot doesn't look as deep as my stock unit (just looks like I need to get a shorter forged bolt from a hardware store), but other than that looks like it would mount up fine.... they say it's 110A @ idle and full 220A @ 1,200RPM's.... 220A is great, considering a 91 Integra alternator, stock, is 30A ,lol.... I was wondering if anyone has any good feedback on the powerbastards??? I know everyone is gonna shout Iraggi o…

Ok, so I decided to go with a Alpine 9887 with the time imprint. my next question is can this deck do a good job if I run my mids active? I have never tried to run an active setup before, and was hoping you guys could point me in a direction as to how it all works. I know you need to run each speaker on a seperate channel of an amp. So, I will have to buy another mid amp. Now would I just use RCA splitter on say the front right to get my mid and highs seperate? Now I also read that you have to run it in full range and control it all of of the deck EQ is that correct?

Ok so today i was resetting the gain on my Sundown Audio SAZ-2000D. I was using a 50hz tone using a dmm. I realized that once the gain was turned up to a certain point it started to make a weird humming sound. I could hear it from inside of the amp on the side closest to where the settings are. Any ideas of what it may be? The 50hz tone I have repeats in 10 second intervals. I can only hear this humming sound from the amp during the 10 seconds. And yes I'm not hearing the noise coming from the speakers inside. Why does the amp only make this sound when the gain reaches a certain point?

epicenter....... when/why do people use them..... are they a waste of money??

My friend wants me to put these in his truck and I want to get everything out of them both. The sub is single 2 ohms 300 watts rms, and the amp is 300 watts bridged at 4 ohms and 150 wattsx2 at 2ohms. Is there some way i can wire it to get the 300 watts or is he going to have to deal with the 150 or get new equipment? Thanks

Due to some unforeseen circumstances (dealing with a disreputable online retailer) it appears like I will shortly be in possession of 2 amps instead of one. I had just wanted a 2 channel amp to power my Phoenix Gold RSD65cs components and then I was going to determine whether or not to add rear fill or a sub with another amp down the road. But now, I have an MB Quart DSC280 (80x2 at 4ohm) and a Planet Audio RX4.400 (100x4 at 4ohm) to be delivered this week. My wife is less than impressed with this turn of events and says I can only keep one and will have to sell the other. My first question is, assuming I follow orders, which amp do I keep. I'm pretty sure the MB Quart …

I don't know much about this battery, but was wondering how it worked. http://www.sonicelectronix.com/item_13167_Kinetik+HC16V+-KHC-16-.html Would it be possible to connect the 12v post to my normal system (12 volt alt), and connect the 16v post to the amp and have 16 volts on that side? From the description that's what it seems like, I was just wanting some clarification. Thanks

i got a md1d amp from usamps it has a bass knob with a little led light in it does anyone know where they sell a led bulb that small so i could change it to a different color?

How much wire should i purchase from knukonceptz for the big 3? and should i get the 0 gauge or will the 4 gauge be just as good? I have a 12" fi bl on a sundown saz 1500d in a 2 cuft box tuned to 35.5hz. thanks