Amplifiers / Head Units / Processors / Electrical

I am getting two 600w rms 4ohm subs and I am getting a mono amp. I was wondering If I wired both subs together into the amp, How would the power be split to goto each sub. Also Would it drop the impedance to 2ohms. So if it did that would I have to get DVC subs? So, for two 600w rms subs single or dual voice coil subs, what would be a good mono amplifier to use to push them to the full 600 watts. Thanks ~Thomas

I have an 06 impala and plan on installing my head unit in the next few days... I was wondering if anyone knew if it would hurt to hook my deck up without using the door chime box with the stage 2 harness. I have a bad habit of not wearing my seatbelt and do not want to listen to my car beep over and over again when im not buckled in . Does anyone know if it would hurt anything to just wire up the harness and cut the chime box plug off (or just leave it unhooked) when I install my stereo?

Hey guys i was looking around on ebay and i saw this little gem MKll Version Tripath TA2020 PCB 25w CLass-T amplifier - eBay (item 250628158856 end time Jun-05-10 08:20:12 PDT) What i wondering is that this set doesn't come with any instructions and it doesn't specify exactly what cables it comes with. i want to know what will i need to be able to run this setup. i have a pc power supply that i use to power a pioneer cd player, i was hoping that could work? and if anything that i need , please let me know thank you Brandon. Read more: TA2020 chip amp - Home Theater Forum and Systems - HomeTheaterShack.com

i got 2 RE HC 12s, i have em in a 6 cubed box tuned to 31 hz, wit a mtx 1501d powerin both. I think i hooked them up wrong or something, Cuz my rearview mirror dont even vibrate. and my friend can do that wit 500 watts. i used the wiring wizard at rockford fosgates site running it on 1/0 gauge wire http://www.rockfordfosgate.com/rftech/wiri...x=21&image.y=13. personally, i believe that i should have hooked each speaker to a different speaker output on my amp. Heres some pics ofwaht the outside of amp looks like. http://www.crutchfield.com/S-kNz22QCXzEr/c...&display=XL#Tab and, http://www.crutchfield.com/S-kNz22QCXzEr/c...&display=XL#Tab I dont no what phas…

I am looking to get yet another alt for my car and I know iraggi makes good ones but has anyone used one made by excessiveamperage? I dont want to get ripped off like I have read few have.

Ive been looking at DC alts for my truck and they go from 2005-2009. The 2010 is the same gen and engine as the 2005-2009 im guessing they just left it off the list by accident just wondering if anyone knows for sure if it would work or wouldnt for some reason. thanks in advance.

I been trying to do some research on some 7-7.5 rms amps but not really making a ton of progress. What are some good amps that's within this power range with the exception of dc. i know b2 m1s and ns1 v2 are in the category but what are some others than im overlooking? i need two budget is $3k

Newb here. Im thinking of getting a rear battery in my tahoe. I've done the big 3 in 1/0.Some people tell me to run the positive wire from front batt. Others say run it from from my alt to rear batt. For grounding some say go from negative on front batt to negative on rear batt. Some say ground to the chassis. Some say get an isolator and relay. What am I really suppose to do and do I really need an isolater and relay. What do they do

i have a popping sound though my sub when i turn off my radio or when i change a track, turn it on mute it will do it when i step on the gas , i first had 2 w6( old school 12s) and a directed 600d amp it never did it when i had that set up, but when i put this one in it started doing it after i played it cupble of times, so what could be the reason.

with christmas coming up and me "getting" some polk audio speakers for my tahoe as a gift, what should i get myself?(lol) i am torn between the pioneer and the jvc(i'd probably be getting them off of sonicelectronix) http://www.sonicelectronix.com/item_19739_Pioneer+AVIC-X910BT.html $699 + already has bluetooth - would need to get the steering wheel controls($70) http://www.sonicelectronix.com/item_12317_JVC+KW-NX7000.html $709 + large sexy screen + remote control + garmin nav - bluetooth would be an additional $70 the boot-up times dont seem to be an issue, since from reading they both start audio upon ignition, it would just be the nav that takes a while i want either …

Im building a sealed enclosure for my 2 15" Obsidians that's gonna be about 4 Cu Ft. after displacement. I plan on using my Hifonics Zeus 2000 which has a subsonic filter on it which for my ported enclosure I set about 5 Hz under my Box tuning. There's no option to turn the Subsonic filter off so I'm wondering what exactly I should set it at when using it for a sealed enclosure. Sorry if this lacks detail I'm unsure how/what to base setting it off of so I'm not sure what else to include.

Alright, I can get this amp for 350$ maybe a little cheaper. Would this be good for an 18" btl? I don't want to push 4400 rms, becuase my box is 7cb ft, so I figure I could just put the gain down a great amount. I know these are power hungry, but aren't tehy like 450 amp draw? I would have 2 C&D tech batteries (88 amp/hr with a rating of 340 watts/cell), 2 ought wiring, 200 amp alt, and soon down the line upgraded under the hood batt. Would that be sufficient? Would these be a good match if I set the gain according to like 2500 watts?

I have a stupid question, but can you strap an AQ 2200 to an AQ 1200 and run 2 subs on it or would it put it wayyy out of phase or something

Hey guys, I have been searching high and low trying to find a bass knob for my Sundown Sae-1200d, and I cannot find one anywhere. Any suggestions as to where I can find one?

Well today i installed everything the concept amp and the SX 15. well about an hour ago. i turned on the car and no sound then changed cd. and nottin then i hear a BOOM BOOM BOOM BOOM and look on the side of the amp and it shows cliping. and its going hard to where my lights dim crazy. the sub is a 2ohm sub i wired down to 1ohm for 1200 watts. what could be the problem the RCA's worked this mornign when i had my 500 watt amp. THANKS ALOT.

So Friday I did a thing....ordered a new Jeep. Needless to say im pretty stoked. I ordered it with the Sound+Leather Upgrade. But did not opt for the $700 430 HU. Now im looking for a decent in dash to replace the 130 radio. Im just not quite sure what to look for...the last HU/Processor i bought was about 6 years ago (Alpine d310+h701) Thoughts/Suggestions/Links Please! Thank you in advance https://www.amazon.com/Pioneer-AVH-X2800BS-Receiver-Bluetooth-SiriusXM-Ready/dp/B017LKVCIK/ref=sr_1_5?s=car&ie=UTF8&qid=1491101412&sr=1-5&keywords=double din&refinements=p_89%3AKenwood|Pioneer https://www.amazon.com/Kenwo…

I have the Pioneer AVH-3200DVD And I cant seem to play vids from the USB Can anyone help me out or had the same problem

Ok here's my problem. Whenever I turn up my Head unit (New Sony Xplode) past a certain point my amp will shut off. As long as I have my amp turned pretty far down it wont do it. But I feel like I'm being robbed of the potential of my speakers. I thought that maybe it was the amp so I took my other amp out of my other car and it did the same thing but even quicker cuz it's a 900w Lanzar and the other one is a American Pro 600w. I've checked all of the connections way to many times and never found any problems. Someone told me that the ohms has to match up on the amp and on the subs but i've never heard of that. If any one has any ideas please let me know i would app…

Has anyone else had the whining noise from the RCAs with the 880? I was switching around some wiring today, accidently touched a speaker wire to the ground wire on the amp and all of a sudden I hear a whining when I turn the vehicle back on. When I grounded a single RCA on the front pre-out the sound nearly went away, still there just barely audible So a couple quick questions about this.... When grounding the RCA would I have to do it to every pre-out being used? (white and red of all 3 pre-outs if all were being used?) Is there a nicer looking way of doing this? Should the deck just be sent to pioneer to be fixed instead?

ok i have this amp and i want to run it at 2 ohms how do you wire 4 6x9s that are 4ohm to make an overall 2ohm load while using all 4 channels? http://www.onlinecarstereo.com/CarAudio/Pr...ProductID=19342

I have bought 4 2608d's for my setup and I have several threads where people have said you can get better amps. The thing is you can always get better amps becuase some company will always make something better. I have been installing for 20 years and have seen almost everything from the begining and have fallen in love with many amps only to be let down by the company becuase they stop making something, it's the nature of the biz! anyway I will post actual test results of my setup and prove or disprove all theory's

what are your opinions on these models? Planet Audio AP3000D Class D 3000W Monoblock Apocalypse Series Power Amplifier $354 3000W Max X 1 @ 1 Ohm 2400W RMS X 1 @ 1 Ohm 1600W RMS X 1 @ 2 Ohms 1000W RMS X 1 @ 4 Ohms Planet Audio AC3000.1D 3000W MonoBlock Class D Anarcy Series Power Car Amplifier $219 1500W x 1 @ 4 Ohms 2000W x 1 @ 2 Ohms 2800W x 1 @ 1 Ohms

i have a Kicker KQ5 i picked up for 50 bux. i had it posted for sale, 2 people are interested, but i think i wanna keep it now becuase its black, and lights up green or amber, and amber lights match my interior perfect. i was gonna get the clarion 7 band one i think it was for like 80 new, but it only lights up blue which would be the only blue, and stand out horribly. my amps im getting (MTX) will even light up amber to match! (my nakamichi cd-400 does too) any other EQ's that have amber lighting?

Well today at the TBP bass wars event, I found out that I'm not getting any voltage readout off the RCA's from the headunit. Tried it with several meters and it wont register anything, just shows 0.00 .....So apparently, I'm not getting any RCA voltage input to the amplifiers... Someone suggested I needed a line driver to solve this problem. My question being, would this solve the probem....being that I can get a cleaner signal and can adjust it to the voltage I want.. ? Thanks for any help guys, it is very much appreciated........I'm still learning, so please bear with me...

need some help with gf system she has two 15" RE SX with a p.o.s. amp from sound storm that she picked out for the price, she has a 1800 kinetik batt in the back its loud now but it could b alot lounder so what amp would you suggest