Amplifiers / Head Units / Processors / Electrical

I am going to be running, eventually, 2 BTLs off 2 Sundown SAZ-3000s. I'm throwing in a DC power AD 250 Special Purpose. DC is building it custom for my car and is the best offer I can find. Thanks Robbie. Anyways, now, the LAST THING I have to decide it what battery. I have it down to Batcap 2000(already have 1) and PM 3100. I'm going to get around 2 more for now, more later. What is better for a daily with a whole nutload of power? Could I mix and match? 2 and 2? try and get the best of both worlds? Thanks!

i am ordering knukonceptz 1/0 and im getting my fuses, what size should i get my fuses, i am running 2 from batt to powermaster 2400 and one from powermaster to amp.

im about to do my big 3 in 4 gauge this week, but I'm wondering if I should just sack up and do my amp power/ground + big three in 1/0 gauge instead, for 600w rms.. would i notice any difference or would i just be wasting my money? (i have stock electrical w/ only 4 gauge going to my amp right now) thanks. this is my third question of the day sorry everyone!

im upgrading my battery, and im obviously wondering if theres some kind of limit as to how many amps the new batt could be before i start damaging the alt? and do bigger batteries NEED a big alt or would say a 1500 amp batt be ok with a 120amp alt? i guess i just need a batt that my alt can actually recharge.... im really clueless when it comes to batteries and alts any help is greatly appreciated!

I was going to get the alpine 9886, but I came across the amazing deal for boxing day, Amazing Deal on HU Has anyone had any experience from this particular HU? I havent come across 1 negative review on any site, other than Pioneer's grounding issue, im not to worried about that.

I have one run of 4g to my 730wrms amp, with big three done in 4g, but I'm still dimming really badly. im almost positive its my batt, but i haven't tested my alt yet.. anyway, which of these batteries should i get (to replace stock batt): kinetik hc 1400 - ah:60 amps: 1500 kinetik hc 800 -- ah:36 amps: 950 or something else that will hopefully solve my dimming problem? i dont know much about batts, any advice would really be appreciated. thanks to all.

a friend of mine keeps going on about this company so I looked into it and found a D3500.1 for a reasonable price but the guts didn't look too smashing are they really that good?

Has anybody checked this amp out yet http://www.audioque.com/aq/AQ3500D.htm I know the 2200 AQ is good and does rated power, should I expect any less from the AQ 3500 ?? Thanks

would you guys recommend- 1. running power from battery to the cdplayer instead of using the factory harness? 2. grounding to the fire wall or use the factory harness? deck is the clarion mentioned in my build log (the cheap one that can do active)

ok, if i bought about 20 Feet of KnuKonceptz 1/0 Gauge Power Wire and 6 Directed Electronics 63205 1 / 0-gauge Ring Terminals would that be all i need to do the BIG 3?

Ok so heres the deal, futureshop has a 1000W RMS MTX amplifier on for 200 bucks, i plan on buying 2 of them if they are any good. They are fused at 120 amps and look clean. Any thoughts on mtx?

so my buddys had his amp unhooked for a couple months and today i went over to his house and just reconected the power wire and fuzes because thats all that he had unhooked and when we crunk the car and turned the system on his subs just let out what sounded like a 40 hz tone and nothing else his door speakers were playing the song but his subs were just going non stop the system in question is a power acoustic 820 2ohm mono ampand two memphis tens white and black i havent seen the back of the so i dont know exactly what they are someone help me please

Hello all, I have a Sundown SAE-1000D powering a 12" AA Havoc and a 4-channel Kenwood eXcelon powering my mids and highs. With this setup I was having a little headlight dimming at high volumes. Now even after adding the Kinetik HC600 in the trunk I still have the same dimming problem; no better or worse. I am pretty sure I have it wired properly with the 2-gauge run from the battery fused at the battery running to another fuse within 18" of the HC600 then from there to the distro block. Both fuses are 150A ANL's. The only wiring difference I have from the suggested wiring in the manual is that I have it grounded to the chassis in the back as opposed to having a grou…

so as of the economy being dog chit, i am forced to an extremely small christmas, i will have around 275-300 dollars, so what should i go with between a powermaster2400($280) and a kinetikhc1800 ($259.99) i will be running a rockford fosgate t3001bd with a duralast yellow top and a stock alt with all 1/0 awg, i would love the powermaster but i would also like some other little things ya know. so what would be a better choice between batts

I plan to wire my sub to my amp like this, My question is, would it be the same if i ran 1 positive wire out of 1 positive terminal on the amp into 1 positive terminal on the voice coil and the other positive terminal on the amp to the other positive terminal on the other voice coil and the same for the negative?

Are the preamp sub outs on the head unit low frequency or full range then converted in the mono amp? Excuse my ignorance, I'm as "newbie" as it gets with this stuff. Basically, is there a difference in using them as opposed to line out on the 4-channel amp into the mono?

I recently took out my big heavy soundsystem due to the weight in the back causing traction issues up front.( gonna fix that this summer i hope), but for now i took my two kinetic 1800 batteries out. I went out and bought a cheap battery maintainer thing from advanced autoparts, it says 1.5 amp maintain. My question is can i paralled the batteries together and hook both up to this one maintainer or would i need to get another. To me it seems fine, it would still be seeing 12v to maintain. Right?

What is a signal processor? How much? Why would you need one?

I'm looking for some good coaxial speakers. I had a pair of MTX 4 ways and I liked the way they sounded alot, however I can't find them anywhere anymore. What I liked about them were they were built tough and gave me great highs with alot of detail. Who makes tough built coaxial speakers that come in 4 or 5 way 6x9s? I was looking at Pioneer 5 way 6x9s. Are Pioneers any good? I want a good pair of 5 1/4s and 6x9s. I had Kenwoods, but those sucked compared to the MTXs I had.

anyone have any hands on experience with the Soundstream HR crypt 4 amplifier???? need some good power for my 2 sets of JBL 660gti components and want clean power with no background noise..my JBL GTO 75.4ll sux nuts for background hiss is the HR crypt 4 worth the money??

Need a reasonably priced ($200 or less) amp to power two Alpine Type r 12"s These will be going into a '93 range rover LWB. Hopefully in a custom box facing upwards. As of now i want a Hifonics 1208d. What do you think? BY THE WAY, these subs will be used daily. 4g wiring kit.

to run two kicker cvx DVC 4 ohm speakers (will be running them at 1 ohm). looking to spend between 300-350$ if anyone has any other amps they might suggest. Thanks!

I have a friend (yeah, that's how it always starts) that says when he tunes his EQ on his head unit, he just leaves it flat across the spectrum. The only thing he ever adjusts is the crossovers on the amp(s). This is the first time I've heard of this. He says the head unit's crossover points are usually set in the wrong place so it won't get the most out of it something like that. I have a DEH-P600UB with the 7-band EQ, should I follow his advice or just tune it to what I think sounds good (no distortion, etc.)

anyone had any dealings with them? Just wondered what kind of quality and workmanship they put into there products?

I know a guy that has one of these amps that I can get for about 100 bones. I am more than sure its worth it. I just wondered if anyone here ran it and how good of an amp they are?