Subwoofers / Speakers

I have a 12 spoke SI D2 and right now it is running in a sealed enclosure and it is not suiting my needs. I was told if I ported it, it would be a whole other sub. Supposedly sound incredible. Just wondering if anyone could help me out with some box dimensions for a ported enclosure. THe best way to get ahold of me would be to email me at [email protected] Thanks Adam

Why is it that the IXL 10 and 12 inch subs have 1000 watt power handling ratings but the 15" and 18" are rated at 800 watts??

Will there be more components produced? I so much want to get my hands on the 327`s. If you still can make these it`d be great to receive them along with a T-shirt And as i understand, a lot of SI products are ordered from UK lately. Seems the Audi A2 with the Baz-box has caught attention

How are these things? I know not many people like Hifonics but has anyone delt with these

I have a mach5 audio MJ-18 i would like to throw it in a ported box but space is a huge issue. I could do 3.5 maybe 4 cubes at 34hz. will be giving the sub between 600-800 rms. i know its not optimal but it would be better than sealed correct

Currently my plans are to go with a 12" PG Titanium Elite 12" with a PG RSD1200 amp. The setup would be ported, probably 2.5cf tuned to 30-32Hz. But I'm afraid that it migh not be enough. I want something that makes it hard to take a breath at full tilt or makes my vision blurry. Can a ported 12" do this with only 1200 rms? I drive a 2008 Hyundai accent so there's not a lot of room. I could do a 15" but it would HAVE to be sealed. What would you go with? A ported 12" or a sealed 15"?

i can get a pair of koda 6.5 inch components with the tweets and crossover for 175 bucks.. i want something with good midbass but i dont want only midbass. does that sound like a good deal? i had been thinking about the rainbow dreamlines for 300 but i dont know how they compare to the kodas, have heard good things about both but never a comparison. they'll be going in sealed kickpanels in my 87 trans am

Hey everyone, I'm planning on starting my build on my wife's car throughout the summer and want to build a SQ system in her car.This is what I have to work with. I'm skilled in carpentry and know a bit a bout fiberglassing. I'll try and post some pics later to get a visual about the build. FRONT 3-4" front speakers deep into the windshiled (you know the kind) 6.5" door pod openings There is room for a tweet mount above the 6.5". Rear Door 6.5" door pod opening. I could also find a stealthy place for a tweet here also. Rear Deck 6x9" opening I was thinking of installing AA POLY's in the 6.5 openings in the front and rear doors. As far a tweeters, I'm open to suggestions. …

okay now im stuck between the two....a fully loaded 12" btl or a 12" nightshade. which would you guys choose, im sure they are both great woofers.

As I was making some room in my Jeep to get ready for my big move, I took out the subs and noticed that one of them had the dustcap loose and shreds of paper were in the box! Thankfully, the cone didn't shred. The sub still functions but it looks awful. Oh well, part of the game I guess.

Ok so im pretty much getting brand new everything What I have now... HU: Alpine CDA- 9831 Current Amp: Rockford Fosgate Punch 500S And I got a rf 12" sub in the back. Speakers: factory Car: 1997 Honda Accord SE So far I'm planning on.... (havn't bought any of these yet) Im pretty set on the sub and amp, not so sure about the speakers. Subwoofer: 15" SSD w/ copper wire (i want it sealed, but coudlnt find the specs...) $215 ( I might go with the 12") Amp: AudioQue 1200D $240 Front Speakers: im looking at these http://www.cadencestore.com/ProductCart/pc...mp;idproduct=95 $70 They looked like a good deal, but I just want some feedback because I'm pretty new at this. If you…

Hey guys i'm looking for a set of components. With the $500 im playin around with, I figure I can buy a new sub amp, probobally a viper 1200.1 for my subs. I will use my 300 wRMS x2 amp to power some components, which seems like a lot but i think I could get by with gains set low. do u guys think thats safe? anyway my budget for comps is less than $200. I will be installing the mids in my doors, imaging isnt a major concern for me, and I cant build kicks anyway. I'm pretty sure I will do some sound deadening, so I need comps that will do well infinite baffle. midbass is pretty important to me, and I can't stand harsh-sounding tweets, so I guess that means a silk tweeter i…

A little about me. I have been out of car audio for a while. My last setup was two MMATS audio P3 12's in a ported box which was great in my Ford Ranger. I recently bought a MB Quart Discuss 1500.1 from a member here and ran it at 2ohms to a Hifonics Atlas 12 which blew within two days. That was admittedly my fault for turning the gain up too loud. I have a single cab Dodge Ram and would like to stay with one 12" subwoofer. My usable space is approximately 30"(w)X15"(h)X11"(d) for 2.12^3 ft of space. I would like to run the amp at 1 ohm @1500 watts and can spend around $250-$300 for the sub. Can anyone point me in the right direction? Thanks. Looking for a somewh…

Ok guys here's my situation I'm debatign between 2 12's or 2 15's D2's I have plenty of space and power and this is going in my 05 ext cab silverado which would you pick ? 2 12's or 2 15's My power on tap is a orion 2500D and i have about 10 cubes to toy with.

Hi, I'm new to this forum, and i need some opinion, what you guys think of this setup? 4x RE Audio SE 15's in 6.7~7.0cuft Sealed Enclosure power by 2x Sundown SAZ-1500D giving them like 750wrms each. 8x RE Audio RE 6.5 Components power by 2x Sundown SAX100.2 giving them like 75-100 wrms or 1x Sundown SAX100.4 giving them like 80 wrms, I read that the RE 6.5 are rated 50wrms can they take more than that? will the 8x RE Audio RE 6.5 be enough for the 4x SE 15's? What Alternator size will be good for this setup? The ones that have experience with both MTX and RE Audio, will the 4x RE SE15's Sealed be louder than 4x MTX 7500 15's also sealed? sorry for so many questions but …

anybody know of any good component sets for around 100$,size 6.5 with 1 inch tweeters.i been lookink at kiker ks but there around 150$.

Trying to post a design I drew up. Dont worry it is not stick figures. I want to get your opinions on this box and amp rack. If anyone could allow me to send it to them through email and then post it I would appreciate it. I tried to use the "image" option and it did not work.

Just for my curiousity's sake, how many of you have been in contact with Nick, ordered a sub and paid for it already?

Ok so running two rockford p3 15's 2.5 cubic per sub still within Rockford specs of 1.86 to 3.0 cubes. Subs are d2 wired on a RF T1500BDCP at 2ohm so subs seeing a few hundred watts over rms should I be ok with subsonic off? Amps filter is 28hz with a 12db slope . A few people said because I went with closer to the large side I should use the filter but I'm not sure I lose a lot of low end with it on .

Does anybody know if the generic grills they sell at Parts Express will work for the 302's? If not, do you have any suggestions on grills for these?

nick whats the Xmax of the Mags?

well i have a eclipse 8808 sub ( three actually) that had some kind of short were the voice coil leads are soldered to the terminal leads. this has been awhile now so i decided to cut it apart and when i got to a fresh part of the vc leads i was able to see the coil was still good so i cut off the coil as close to the cone as i could mainly to save for dimensions. well i decided to order a rockford fosgate he recone to give it a whirl. the mounting locations for the surround and spider are perfect, but the coil is way to short, and a little to large at its outside diameter. so i am attempting to graph the eclipse coil onto thr rockford fosgate former. i can't glue anythin…

OK... Currently I'm running a pair of PPI DCX 12, they've been good to me, I enjoy them, but they don't have a lot of excursion & it seams like they bottom out on me at times... Lately I've been thinking about getting a RE XXX, either a 12 or 15... What would you do?

Im looking for a sub to replace a 10" IDQV2. I will be running it off a JL 500/1. I like the specs on the Fi SSD and the SSA Icon but dont really see a huge diff between the 2, other than getting the copper coil and BP Power (whatever that is..) on the SSD. Can someone please tell me what BP Power is. I searched but didnt find a clear answer.

I got myself a Diablo Audio HF8000.1. i cant decide whether to go 4 AQ copper coil 12s in a proper size box (8.5), or 2 Aluminum coil 18s in a little too small box (10.5). im not looking for numbers, just a daily beater. my goal is to get loud but retain some decent sound while listening to music. pretty much just sounding decent while listening to music but loud.