Incriminator Audio

Available Monday! 600 RMS and ready to roll!

We are releasing: LI 12 and 15 - D1 or D2 - 600 RMS FL 12 and 15 - D2 only for now - 600-750 RMS DR 12, 15, and 18 - D1 or D1 - 1000 RMS DP 18 - D1 or D2 - 1500 RMS Coming next week - April 3rd! Thanks, Nick

Since we are getting close to the release of alot of new products, I've been getting alot of emails about pricing, so I'm going to post MSRP to give you guys an idea on the direct price point! As you know, no one pays retail on the internet! MSRP: 600 RMS LI 12 - $259.99 LI 15 - $279.99 600-750 RMS FL 12 - TBA FL 15 - TBA 1000 RMS DR 12 - $429.99 DR 15 - $469.99 DR 18 - $529.99 1500 RMS DP 12 - $599.99 DP 15 - $639.99 DP 18 - $689.99 (It's almost here!) Thanks, Nick

I have a gmc single cab ruck. I already have a bed cover and am planning on doing a full blow through (cutting out everything under the back glass) and replacing the back glass with lexan. My problem is that I want to run two dp 21's on a 40.1 but I don't think I will have enough room to run the two subs and the port into the cab. So my decision is probably gonna be between 2 21's with the port somewhere in the bed or 2 18's with the port blowing into the cab. Which of these setups would be the loudest for daily spl? If anyone has any ideas on another way to do this I am open to suggestions. Thanx in advance.

i have an IA40.1 and 2 15" DP's,, i can wire them at 1 ohm or even a quarter ohm,, and still when the music starts to hit ,, it says im runnin at 5 to 6 ohms.. what am i doing wrong? or is that normal??

Ok, so right now I'm running 2 20.1's strapped at 1.5dcr daily and burping at .375dcr. This is on 2 DD3515's w/ 3 Deka 9a31's. I'm pulling my current box out tomorrow (was doing 53's). Will be rebuilding and going w/ a smaller box. The 20's are doing good, but I can't help but think...would a 40 do better? I have never played w/ a 40.1, so I have no idea what they are really like. So, what do you say?

this amp is by far my worst enemy because of it I need to get a new head unit or cd changer it has so much power I can't get a good 30sec. with out my hu skipping like mad. THANKS IA

What are we looking at for airspace on the 21's. I am kinda tossed between the DP 18 and 21. It really is gonna come down to space.

I just got a 12" DP (2008) and im going to be giving it around 3500rms from my 5082hx. what kind of box size would handle that power the best and what tuning should i be after?

Will a massive audio 3000.1 push 2 DP's?

Can a 20.1 operate safely for music "ie bass race or drive by" @.35 ohm on a 16+ volt system?

what size fuse do they need and does anyone know the average curret draw at one ohm load probably 1.5-2ohms reactive. Thanks for any help I can get.

When strapping a pair of 40.1s do you have to change the phase of the slave amp?

Nick- Do you know of any shops in the DC/Maryland/Virginia area that can repair a 20.1 amp? I would prefer to send it to you as no one knows them better than you. I sent you a few emails but just in case you didn't get them can you reply back to brandon.nicholson(at)dot(dot)gov. I'm not for sure what happened this time. It looks as if the power supply may have went out again as the same pieces on the outside edge are burnt. Before I installed the amp this time I had all the wiring re-done professionally. I'm dying without my baby lol. Bass is my Anti-Drug lol. I just received my tax check so repair money is sitting and waiting. Thanks

IA Update 11/29/07 I though I would chiming in to give some behind the scenes insight. Where to start

I'm getting a 40.1 and would like to know if there is a matching 4 channel?

has anyone bench tested on of these I have heard on other boards that they compair in output power to a DD Z1 even though they are rated @ 3600 is this true? thanks

Alright.... here's the deal. I got an IA 20.1 off of the ca.com forums. When I get it it has the following problems, The problem is its randomly going into protect. I resoldered the piece that was disconnected above, I'm assuming it was from the power supply. It doesn't do it often, and it clicks out of protect within about 10 seconds. Is this something that you can fix???

Maybe im just to lazy to look but whats the T/S of the DP 12's

I am trying to find anyone wanting to get rid of a 20.1. PM me if anyone has one to let go thanks.

I know the cones aren't ready for the 21's yet, but the baskets are there, so what's the cutout sizes on both of those, so I can decide which one would work best for my situation?

going to be testing it out in my 6th order bandpass on a Sundown SAZ-3000. I'll post up the results later next week. Here is is next to the competition (still have to drop a recone in it):

Death Penalty Series with MSRP - 12" ($599), 15" ($639), 18" ($689), and 21" ($799) Dual 1 and Dual 2 ohm Standard Black Cast Basket 3" 8 layer Flat Aluminum Voice Coil Triple Black Progressive Spiders with Woven Tinsels Non-pressed Kraft Fiber Reinforced Cone Double Layer Foam Surround Triple Stacked Magnets with Black Nickel Finish Interlocking Aluminum Spider Spacer Assemble CILD - Center Interlocking Dustcap Design for Easy Field Recones ADC - Air Driven Cooling - 6 Aluminum Column Vents for Max Motor Cooling Silver Push Terminals Wrap Around Rubber Gasket The wait is over! The last missing part will be here Friday, so expect pictures this weekend, if not it will be M…