topgun

I'm going to rock this physics test.

Got a legit answer for my question over on DIY audio.

"Studying" for an EPII test that is tonight.

http://www.incra.com/product_tsf_lsts.htm I want one.

Sean's gain is all the way down if I remember correctly.

Same thing.

Sure some of you have seen this before (I have... but I enjoy reading it none the less) Something everybody should know * One Top Fuel dragster 500 cubic inch Hemi engine makes more horsepower than the first 4 rows at the Daytona 500. * Under full throttle, a dragster engine consumes 1-1/2 gallons of nitromethane per second; a fully loaded 747 consumes jet fuel at the same rate with 25% less energy being produced. * A stock Dodge Hemi V8 engine cannot produce enough power to drive the dragster supercharger. * With 3000 CFM of air being rammed in by the supercharger on overdrive, the fuel mixture is compressed into a near-solid form before ignition. Cylinders run on the verge of hydraulic lock at full throttle. * At the stoichiometric (stoichiometry: methodology and technology by which quantities of reactants and products in chemical reactions are determined) 1.7:1 air/fuel mixture for nitromethane, the flame front temperature measures 7050 degrees F. * Nitromethane burns yellow. The spectacular white flame seen above the stacks at night is raw burning hydrogen, dissociated from atmospheric water vapor by the searing exhaust gases. * Dual magnetos supply 44 amps to each spark plug. This is the output of an arc welder in each cylinder. * Spark plug electrodes are totally consumed during a pass. After

Wow, found out I had to check the stupid box at the very top corner that said Yes, I have searched. me = owned.

Fricking diyaudio.com, telling me to search before I can post a new topic. I did search god damnit.

*Reading Martin King's site more*

Ok, question here: On a 1/4 Wave enclosure, find wavelength of Fs of the driver, then divide by 4, stuff the length of the line, driver at one end, open at other end. This is my current understanding of how to build a 1/4wave (correct me if I'm wrong), my question is how does the size of the line (high/width relation) affect the amplitude of the wave produced? Is there some magic ratio that I'm forgetting or something? Or is there a link on where to read more on this? Or just tell me I'm a fricking idiot if I've got it bass ackwards

Redbull tastes like ass to me, my cousin absolutely loves it though.

Eh, if I drink coffee it is leaded, straight black, nothing in it.

Fricking Sexalicious.

*out to study*

It looks like I can get back into the range at KSU so I can start actually training again.

Got the wild idea of putting my DD1008 in a little box for my computer sub till I can get something new... The only bad part is a DD 1008 sounds like utter chit last time I played with it. *That might be because it was tuned to 40hz though...* Can't hurt to play though.

fudge. I've got to go study physics for the test tommorow afternoon First thing first though, time to go find a 30pin USB cable to charge my mp3 player.

I've never heard anything of building up a new Hemi, actually, I've never really heard anything good or bad about them, except the joke of "That thing got a Hemi?".

My boss and his wife went out and got some icecream, and they brought some back for me too.

Can do.

Got a PE order with 2 TB 3" drivers, binding posts, veneer, and a few other items that should be here tuesday.

fudge me. Why do I always want to over complicate anything audio.

wait, you bribe your customs officer with cartoons? well, i have to get around the fees... Seems like a kickass arrangement to me.

Crap, I just had the idea of putting four of the 3" TB's per side and porting them in a mini array type thingy. Hmmmm