zZZzzzSnooze2nd

You got that vid up?

Got some XCON & DD M2b action for You!! Beating Down the Mirror too XD

I went with direct leads because the push terminals broke off & it was dangling! So I took both off. This XCon is the first generation, it is just under 5 years old. It was reconed before about 2 years ago, and just started using it. it was a bad recone job lucky I ordered 2 recone kits, Dustcap came lose first day out & it was flapping. spider came completely off later. I wanted the job done right, So I did it myself. I think I did it right. I'm proud to say I am no longer a Recone Virgin.

Hey guys, the recone kits came in. He was wondering what Epoxy adhesive to use, He wants to put the same type back on there. He don't have one that drys rock hard like the one that was on my SSA Subwoofer. Before he does the recone, he wants the right stuff holding it in so it don't fly out at me I guess, lol. So if anyone knows the glue that SSA uses, it will be much appreciated. I have no clue if there is only one kind of epoxy glue or different types, I'm assuming there is different strengths? Thanks

No problem, It's all good. I was wondering if the kits came with the glue? the guy doing the recone said it is a more harder glue on my Sub then what he uses on the other subwoofers.

Hello guys, Just here to let you know the recone kit's didn't come in.

Thanks Guys

Got wrong tracking number. Shows it was picked up, But it was Shipped and delivered somewhere in California. Still got nothing here in Canada, BC. I looked & can't find a phone number & emailed them, I guess it is all backed up. So, here I am at the forum now. Maybe here will be faster? #3627 Two SSA xCON 12" D2 recone kits. shipped to V2N-2S8

Made it myself awhile back, Just to see if it will fit the enclosures I was making. It is a perfect copy of the Xcon 1G to see if there is good clearance for mounting depth & to see how the finished product will look.

Tuned to 30Hz Ported, 2.75 cu.ft

I was just wondering if 4 of these batteries will be good for a car audio system. 2,000 watts RMS? This is the only best battery that I can fine in my own town. I can't get XS Power or anything like that. They do sell Kinetik at this one place but they are marked up 50% higher then SonicElectronix & I don't want to mail order any car batteries. There Shuriken batteries at another store too. there marked up high like the Kinetik. I like to buy them in store, If anything gose wrong with them. I can just drive to the store & return it. These Nautilus AGM Deep Cycle batteries are in stock ready to buy. Motomaster Nautilus AGM Deep Cycle 12 volt Battery C$259.99 Brand Name - Nautilus Cranking Amps - 1110 Application - AGM Dimensions - 13 x 6-5/8 x 9-7/16-in Amp Hours - 100 Group Size - 31 Free Warranty Replacement Period - 18 Total Warranty Period - 48 Voltage - 12 Weight - 71 lbs Reserve Capacity - 200

I meant stage inside. Use it on stage in a magic show. iMusic only.

So, maybe i should center the port, Huh? I wanted a tune of 18Hz that's why it is thin.

Yes port is on the top, It was at the bottom but wheels are going there so i flipped it. Port is really wide and only a inch high.

Now if I'm going to use L7's I'll need 2 IPR 6000 running at (4-Ohm@2,000w RMS x2)

(2x) Quad L5 Kickers in a 24cu.ft @ 18Hz, For Stage use. Could use L7 or Solo X! Oh yeah, No SoloX in 15" size. But for the L5 with 3,000w@2-ohm x2 with Peavey IPR 6000. Talking weight here so will be rolling Quad Subs. Let me know whats on your mind good or bad.

Sure, It was late so i removed it from enclosure. I was thinking of making a Bandpass box for it. That can be a Sealed box when Ported side is removed. Not too sure what is the best way to keep them together.

http://www.youtube.com/watch?v=qnkkE-C8QX8

12" SSA XCON D2 Re 3.7 Ohms (1.85 per coil wired in series) Fs 32.4 Hz Qms 5.24 Qes .39 Qts .37 Mms 222 Vas 35 l Sd 480 cm^2 BL 20.65 SPL 86.7 1 W/1m Xmax 31mm Enclosure Recommendations: Sealed: .9 - 1.25 cu.ft. Sealed: 1.35 - 1.5 cu.ft. optimal Ported: 1.75 - 2.25 cu.ft. @ 26-33hz Ported: 2.5 - 2.75 cu.ft. @ 26-33hz opt. Sub Outside Dia.: 12.500” Cut Inside Dia.: 11.150” Displacement: 0.17 cu.ft. ok, BTY the Sub Outside Dia is 12.750” with Rubber seal on.

Nope I didn't fined them, I Made it using Google SketchUp 7. I'm going to remake the hole thing, I forgotten a few things.

I have the 12" SSA Xcon D1, What is the Displacement of this sub? I would guess it's 0.18 or 0.19cuft? Take a look!! It's a work of Art...