basshead7890

Yea, it was a little louder I couldn't believe it either, but they work though

1. Product: Sundown SAX-100.4 2. Specs: 4/3/2 Channel Bridgeable Class-AB Amplifier MOSFET PWM Power Supply Stable Into 4 Ohms Bridged or 2 Ohms Stereo Load Variable Subsonic Filter Independent 1/2 and 3/4 Channel High Pass Filter Variable with x 10 Range Selectable Switch Independent 1/2 and 3/4 Channel Low Pass Filter Variable with x 10 Range Selectable Switch HPF/FULL/LPF Selectable Switch Independent 1/2 and 3/4 Channel Electronic Crossover Slope Selectable Switch with 12dB and 24dB Octave Variable Input Level Control Input Sensitivity : 200mV ~ 6V Subsonic Filter : 10Hz ~ 500Hz Signal Input and Line Out RCA Connectors Multi-Way Protection circuitry (Thermal/Over Current/Speaker Short/Speaker DC protection) Tested Voltage & THD: 14.4V & Less than 0.05% THD Operating Voltage : DC10V~16V Power Input Rated power output ----RMS power, 4 ohm stereo 100W x 4CH ----RMS power, 2 ohm stereo 160W x 4CH ----RMS power, 4 ohm bridged 320W x 2CH Signal to Noise Ratio >90dB Low pass frequency crossover 50Hz~500Hz (CH1&2) 50Hz~5KHz (CH3&4) High Pass Crossover 50Hz~5KHz (CH1&2) 50Hz~500Hz (CH3&4) Variable Subsonic Filter 10Hz to 500Hz Frequency Response 10Hz ~ 40KHz (+/-1dB) Bass Boost 0~18dB Variable Bass-Boost Frequency Control 35Hz to 120Hz Frequency Response 10Hz ~ 40KHz (+/-1dB) THD@RMS Watts <0.1% Channel Separation 75dB Fuse Rating 30A x 3 Input Sensitivity Variable 200mV~6V (+/- 5%) Dimensions 252(W) x 58(H) x 480(L)mm 3. Description/Condition: 10/10mechanical 7.5/10 cosmetic A little dusty and a couple of small nicks & scratches. 4. Price: : $250 shipped No Trades 5. Pictures: \

Not yet, I just threw that together last night to make sure they would fit and fold up

Here's a mock up of the amps

Execution Audio 1/0 for 2 ground run from front to back

1. Product: 2 Skar Audio SK-2500.1D 2. Specs: Class D Digital Monoblock Amplifier Compact & Versatile Design Linkable / Strappable 4 Way Protection Circuitry : Thermal, Voltage, Speaker, DC RMS power @ 1 Ohm : 2,500 Watts x 1 Channel (14.4v) RMS power @ 2 Ohms : 1,450 Watts x 1 Channel (14.4v) RMS power @ 4 Ohms : 790 Watts x 1 Channel (14.4v) RMS power @ 1 Ohms : 2,900 Watts x 1 Channel (16v) Frequency Response : 15~270Hz Input Sensitivity : 6V~0.2V Signal to Noise Ratio : 95dB Damping Factor : 200< Low Pass Filter : 35Hz~250hz Subsonic Filter : 10Hz~50Hz Bass Boost : 0dB~9dB Phase Shift : 0~180 Degrees 1/0 Gauge power and ground Terminals Working Voltage : 8.5V~16V Remote Gain Knob Included Line Out rca Connection Dimensions : 520mm (Length) x 241mm (Width) x 64.5mm (Height) 3. Description/Condition: Has a couple of small nicks and scratches and the mounting feet are a little bent 10/10 mechanical 7/10 cosmetic 4. Price: : $1000 shipped or $500shipped each Only trade for Sundown Saz 2500v2 or v1 5. Pictures: ** DO NOT DELETE ANYTHING BELOW THIS LINE OR THREAD WILL BE DELETED ** ----------------------------------------------- This message is automatically inserted in all classified threads. Please be advised, all buyers and sellers should satisfy themselves that the other party is genuine by providing the following via PM to each other after negotiations are complete and prior to dispatching goods and making payment: 1) Telephone number. Call the number back at a unspecified time and make sure that it is the person's correct phone number. 2) Name and address including postal code 3) Valid e-mail address. Send an e-mail requesting a response to information about the deal being made. DO NOT proceed with a deal until you are completely satisfied with all details being correct. It's in your best interest to check out these details yourself. If transaction was completed on ****, please use iTrader to record feedback. Potential buyers/seller should check iTrader feedback also before continuing transaction.

Yea

I traded my 1500s for these This is how they were shipped

lookin good

2nd coat of paint

First coat paint

Thanks and yea but I'm just going to stick with black thanks

one of my Funkin' Audio RCA cables had a short in it when I got it, so I contacted DIYMA and they sent me 2 of there's for free

I haven't got a chance to meter it yet

I like it, to me it sounds better and easier to mount

What motor will be using it?

The recone I blew Also I just picked this up

That's horrible! You didn't go ham on it right off the bat did you?Yep full tilt like did all my other subs. Never had a problem before.I personally would not go balls out until at least a couple hours play time to loosen the suspension a bit. Out of curiosity though where was the failure at?I think the coil unraveled, when I press down on the cone it barely moves and I can hear scratching. My other coil was still working when I reconed it. Only reason I recone it was because when I bought it the cap was lose and I put goop and the original glue on different places on the cap coming loose so I put more goop on it till it just became an eye sore.

That's horrible! You didn't go ham on it right off the bat did you? Yep full tilt like did all my other subs. Never had a problem before.

Got it playing and it blew 30 min later