edouble101

At the end of the video it looks like a distorted my phone's camera sensor lol.

I got my automotive 4/0. I will be adding a run from alt to rear battery and a ground run. Here are pics compared to my Stinger HPM 1/0.

I will soon. I have a few annoying rattles to tackle first.

You waste no time!

Stinger 1/0 is about $4.59/ft this 4/0 is $2.98/ft, 35% cheaper. + More copper = better voltage over longer runs - less flexibility

I ordered 50' of this 4/0. Pics compared to my Stinger 1/0 HPM that I have been using. BTW Stinger HPM is on the small side for car audio 1/0. I am curious how this wire compares to flexoprene 2/0.

I love 4Runners. Have fun with it!

Nice planning! Have you used PWK before?

I will have to check those out!

I would love to get this on a meter someday. I wouldn't doubt one bit if it was +145. Sounds so good doing it

Thanks Stefan! I gotta say, this single 18" Z.3 is f'n nuts! Sounds amazing and gets as loud as I hoped it would! I am anxious to hear how this sub system is going to sound after the sub is broken in. My Excessive amperage alt and external regulator are holding voltage consistently at 14.5v, even during heavy bass hits. I can get the voltage to dip into the 13's if I adjust the volume waaaayyyy up. 50' of 4/0 is ordered Glad to hear the Z3 is sounding good, and loud. I wish you could hear it! This setup is just balls to the wall nuts! Thanks again for helping me get my enclosure dialed in

2.0^3ft tuned to 33hz will be just fine for a single 12" Z.3 I choose the Z.3 as well. I like to be able to get nuts with the volume control once in a while but my real passion is for clean, detailed music. The Z.3 fits the bill. Amazing driver.

How would you compare the SP4's to other drivers you have had?

Good job on your first event! That Blazer looks nuts. Whats in it?

This really is a shot in the dark. You have two very well matched drivers and now you want to find a tweeter to fit that pair. Check out the Morel CAT 408. It might be a good fit for your set and a good candidate for kick panel mounting location. I still prefer tweeters up high. Too bad the cross over point is right in the middle of vocals. You are limited to mounting the tweeter and mid very near each other. I prefer a-pillar setups. Have you considered that?

Nice looking truck! This should be loud!

Nice build! I bet this is loud as fawk!

I have a Nikon D7000. That picture actually isn't very good. I have blown out highlights on the 900.6 I just snapped a single pic in auto. If I would have closed the car doors to shut out some of the daylight and shot in manual mode I would have had a better picture.

Thanks Stefan! I gotta say, this single 18" Z.3 is f'n nuts! Sounds amazing and gets as loud as I hoped it would! I am anxious to hear how this sub system is going to sound after the sub is broken in. My Excessive amperage alt and external regulator are holding voltage consistently at 14.5v, even during heavy bass hits. I can get the voltage to dip into the 13's if I adjust the volume waaaayyyy up. 50' of 4/0 is ordered

Looking good so far. Tuned in for more progress pics!

Thanks All controls are assessable with the seats bolted down

The amps are mounted. I still need to build my false floor. The 900.6 is powering my component set for now. Shitty picture, I was in a hurry Up next: Make a false floor, fix roof brace and finish making a trim panel for the aero port. After that is front stage

Excellent company to sell!

The sundown Z series subwoofers are geared towards SQ. And like all sundown drivers they will take a beating and get loud if you want them to. SSA icon is also a good sounding driver. The Z is another great option