sundownz

These are due in about 4-5 weeks from today. Neo-Pro 8 - 100 watts RMS / 8 ohms * Neo-Pro 10 - 200 watts RMS / 8 ohms * * Assuming proper crossover frequency for your application; typically 80 Hz or so but perhaps higher or lower depending on the power and size of door. Frequency response is good to ~5000 Hz on these -- they are a high Qts design for IB door installations in a car audio environment. To order send a Paypal to me at [email protected] Pre-Order as follows : Eastern USA : States not listed under western USA. Neo-Pro 8 - $80 shipped EACH Neo-Pro 10 - $95 shipped EACH Western USA : ND, SD, NE, KS, OK, TX, NM, CO, WY, MT, ID, UT, AZ, NV, OR, WA, CA Neo-Pro 8 - $85 shipped EACH Neo-Pro 10 - $100 shipped EACH AK and HI must contact me for quotes. ---------- ----------

I'm guessing that a large amount of these amps will power the big "PA speaker" setups -- so numerous speakers can be wired per channel in parallel.

In-stock ETA is first week of May. Did not make original early April ETA.

I will be looking at a big two-channel again but not quite the same as this one... I want lower impedance stability which this amp didn't have.

Looking good !

Back from SBN so time to start catching up - had a good time !

The SA can take some good burp power... we have done 2.2k on an SA-8 stock copper coil @ 68 hz -- and they use a smaller 2" coil vs 2.5" on the bigger SA

The v.2 does everything the v.1 does.

http://www.sundownaudio.com/misc/Russia/Russia_Magazine.pdf Full PDF of the Magazine -- the the Mazda on Page 61 - 65 Nice cover shot too !

Come on by

Essentially the only real T/S change is the Le -- which dropped from 7.70 mH to 4.85 mH on the D4 coil

D2 specs with a very short break-in period : Re : 3.94 ohms Fs : 34.62 Hz Qes : 0.52 Qms : 4.34 Qts : 0.46 Le : 3.57 mH Vas : 17.16 L BL : 23.28 NA Mms : 328.7 g Cms : 64.27 uM/N SPL : 83.11 dB 1w/1m Xmax : 19.0mm one-way Bl^2/Re : 138

I got my samples in with shorting rings and new pole flares -- I will be breaking them in to measure T/S within a week or so in order to get "official" updated TS for the site for SA-10/12/15 : * NEW FLARE * OLD FLARE The flare will also allow people to immediately identify if an SA has a shorting ring or not -- as only SA-10/12/15s with this style flare will have a shorting ring.

Essentially what I'm saying is stating the "efficiency is horrible" is not correct; as sensitivity does not = efficiency -- at least not on sub-bass material. Which is why I posted the linked thread originally If you climb to over 50-60 Hz then, sure, a sub with a higher "sensitivity" would gain in output -- but for what people want in a true car audio sub-woofer (small box / tremendous low-end) this type of parameter set works great. It's very similar to the SA line in parameters.

Please read : What your statement should read is... "Looks like it will have great bottom end in a small box"

D4 specs with a very short break-in period : Re : 7.00 ohms Fs : 34.61 Hz Qes : 0.57 Qms : 4.45 Qts : 0.51 Le : 5.05 mH Vas : 17.39 L BL : 29.23 NA Mms : 324 g Cms : 65.1 uM/N SPL : 82.7 dB 1w/1m Xmax : 19.0mm one-way Bl^2/Re : 122 With break-in the Fs and Qts will drop a bit as well.

All items listed before sold... will update again some time soon.

That has been gone for year now! i know it has been...im just giving jake a hard time for not bringing it back Still working on it

It is something I have considered but haven't seen a huge market for at this time since we offer multiple coil configurations people can get the power they need @ 1 ohm.

For the month of March our SAX multi-channel amps are on special ! SAX-125.2 : Regular - $250 MAP SALE - $205 SAX-100.4 : Regular - $385 MAP SALE - $345 SAX-200.4 : Regular - $815 MAP SALE - $650 You can order from your favorite local or online dealer OR you can Paypal me at [email protected] to order. This is for the month of March only and in the USA only. For Alaska and Hawaii SH quotes e-mail me -- otherwise the above are shipped in the continental 48 states.

Some of the parts were completed -- I am awaiting pictures and information. As with anything really cool it is taking longer than expected

If we are super busy, like right now, it takes longer to ship items and/or to respond to inquires.

We haven't re-coned any E8 v.2s yet. Have alot of inquiries on v.1 re-cones but I need the adapter made for the frame which I haven't had time yet.

Yes, if you want a quote email me.

Oh, I meant I was paying Sundown. So that's why I'm so surprised you giving up somebody paying you to work. Shame. My feelings are hurt and I will not work under these conditions. I don't remember that -- did we really talk about that ? Lol. No. I kid I kid. I was hoping when I said I would pay to work you would figure it out. But if I would of lied, does that mean your down with me coming to work? *laughs* Anymore I can barely remember stuff as so many things are going on - probably could have fooled me