sundownz

Based on the market segment I am hitting on -- a true sub-woofer -- the motor size isn't much of an issue. ----- When you move on to something that is, by design, also a midbass / midrange the smaller motor is a consideration; see NS-6.5CS : http://www.diymobileaudio.com/forum/1721077-post10.html Even then the motor is still fairly large (for reference the NS-6.5CS set has about 12mm linear). Obviously alot smaller than the X-6.5SW but not a tiny motor at all. For reference; the NS-6.5CS midrange costs ~2x to produce than what the X-6.5SW does -- I don't see that hitting the market niche of the X-6.5SW.

Also... ETA is pending on them but my best guess on it is November to December.

Been working on this guy for a while now... what I hope to be final prototypes just arrived a few days back. Based on our testing I am going with a 750 RMS rating on these. I won't say people will not be able to run more... but that is our official rating. They will cost $210 from an authorized dealer. Production models will, of course, have a gasket and magnet boot. ----- * Compared with SA-8 v.2 * Compared with SA-8 v.2 * Compared with X-6.5SW * Compared with X-6.5SW

We have sold several 100 sets -- feedback is overwhelmingly positive. There are not a fancy LOOKING set but the sound is pretty incredible in the price class -- VERY smooth across the board. The only folks that aren't entirely pleased prefer a sharp metal tweeter sound; as ours is a smooth silk dome. There are no plans to eliminate them from the line; simply to tweak them a bit as time goes on.

No there is not. It would not glue to the cone properly as it glues to a flat diaphragm.

Spec sheet from factory LMS : I measured Le on my Woofer Tester II as that was not included at 1.81 mH

Our life-test at the factory passed 300-watts RMS for 12-hours full bandwidth in a sealed box -- so I will probably rate it around that.<br /><br />JUST got the e-mail in confirming that -- we'll also do our own tests.

We got the first prototype in here to test and I LOVE IT !!! Cannot wait to get rolling with this project They should cost $130 MAP from an authorized dealer. * With Blackberry Z-10

Z v.4 18" D1 : Z v.4 18" D2 :

Z v.4 15" D1 : Z v.4 15" D2 :

Z v.4 12" D1 : Z v.4 12" D2 :

See below for X series production parameters : ----- X-10 D2 : X-10 D4 : X-12 D2 : X-12 D4 : X-15 D2 : X-15 D4 : X-18 D2 : X-18 D4 :

These are ETAs -- estimated time of arrival. They can vary a bit. X-18s first segment : THIS WEEK; should fill all the "individual" pre-orders X-18s second segment : 8/28/13 Z v.4 10s : Should already be shipped... we built all of these as none were made in production quantity. Z v.4 12s first segment : 8/12/13 (should fill all pre-orders) Z v.4 12s second segment : 8/28/13 Z v.4 15s : 8/28/13 Z v.4 18s : 8/28/13 ------ Other items that are sold out : SD-2 10" D4 : THIS WEEK SD-2 10" D2 : 8/12/13 SD-2 12" D4 : 8/12/13 SD-2 12" D2 : 9/5/13 SD-2 8" (D4 only) : October SA-8 v.2 D2 : 8/12/13 E8 v.3 D2 and D4 : October E-10 D2 and D4 v.2 : Within 7-10 days E-12 D2 and D4 v.2 : Within 7-10 days E-15 D2 and D4 v.2 : October to November Z v.3 Motors : 8/12/13 * We are still producing them. NeoPro v.2 (ALL sizes / 4 ohm and 8 ohm) : 8/8/13 ------ MOST of the X series are sold out at our warehouse as of now... once the dust clears I'll get more info on what we do have left. I started more production of these first week of June; so that should mean we'll have more early to mid September. In the mean-time WoofersEtc will have a good bit on hand of most if not all X series drivers; both customers and dealers will be able to order there. They also have many of the above listed out-of-stock items in their inventory as well -- and again, dealers and customers can order there as WoofersEtc is also a distributor.

New cast frame with under-spider venting, revised motor ventilation -- thus higher power handling. Also come with grilles... and we moved them to a new build-house as well for tighter QC standards. All at the same price

NeoPro-v.2 Info below. They will be in stock mid to late August. New power ratings : 6.5 - 180 RMS 8 - 200 10 - 300 * Included Grilles And mechanical drawings : http://www.sundownaudio.com/misc/protos/NeoPro_v2/NeoPro-10%20V.2%20mechanical%20drawing%2020130716.pdf http://www.sundownaudio.com/misc/protos/NeoPro_v2/NeoPro-8%20V.2%20mechanical%20drawing%2020130716.pdf http://www.sundownaudio.com/misc/protos/NeoPro_v2/NeoPro-6.5%20V.2%20mechanical%20drawing%2020130716.pdf

I've mainly been updating on Facebook but we have been heavily involved in moving our location about 20 minutes down the road to Claremont, NC to a much larger facility for most of July. We now have functional shipping, testing, and build room areas at the new location plus a few office guys have transferred over as well. It has been a bit of a long process but it's coming along nicely. I have not yet moved my office or Debbie and the accounting / invoicing systems so it's been a bit inefficient as the data has to be transferred to the new location to ship (aside from Yard Sale) -- but the goal is to move all this by Monday and have everyone working in the same location by then. This should bring us back up to speed again. Also... at some point we will have to cut off the phones for a bit to move our phone number and phone system -- I will post up before we do that and update when the process is completed.

It has come to our attention that 3 Kings Audio is selling Sundown Audio products. They are NOT authorized and products bought there will NOT carry our manufacturers warranty. All of our authorized online dealers are listed on our web-site. It is only possible for us to ensure the quality of products sold through authorized sources; do not trust an unauthorized source as you also cannot be sure of the authenticity / A-Stock quality of the product. Any dealer or distributor found to be supplying unauthorized online sources will be terminated. We would appreciate any information that anyone may have about the source of these unauthorized products.

Occasionally the factory will over-print one type of box (D2 or D4) and use a label to correct it -- I am unsure why they would have re-labeled a box and made it wrong; but that appears to be the case here. If we were notified when the product arrived we would have swapped it out right away as it's a factory packaging error. As the product has been re-sold and used for some time at this point there is not much we can do nor is there any more useful life in this discussion; so I will leave it here and close it.

They are shallow enough to fit many factory apps; our dealers requested them as close to 4" as possible so they would work for that -- so yes, it's a target market for them. I have a very nice application in my truck for them -- I'll be down-firing 8 of them behind the rear seats in a ported box.

We are still developing the soft parts a bit at our factory; here is a video on the 2nd prototype with a small revision we made to the surround material : "Early sample test. We are tooling a new spider to go with it as well. There is some high frequency sound which is a little bit of clipping of the source unit." "Test at one frequency / maximum mechanical travel -- testing for ruggedness." At this point we are beating them silly just to test ruggedness -- so we are pushing them well into mechanical noise territory to do so. When I get my hands on them I'll do more videos at varying levels of excursion, etc.

SAZ-5000D and NS-1 v.2 Photos : * 5000D has integrated PCB fan.

Info on the other amps will be coming along as well ; but not today -- so I didn't forget; just stay tuned

Some 150.2 and 100.4 v.2 photos : * SAZ-1200D above the SAX-150.2 * 150.2 crossovers * 150.2 internals. * SAZ-1200D above the SAX-100.4 v.2 * SAX-100.4 v.2 crossovers * SAX-100.4 v.2 internals

Been doing alot of work on some new amp products -- I don't get the time I used to on the forums to keep everyone in the loop but I'll go ahead and announce them today! Production is starting this week so we are looking at ~90 days or so. I won't be starting pre-orders right away but do expect a pre-order at some point once I get more solid time-lines. SAX-150.2 ($400 MAP) : Two channel Full-Range Class-D design (similar to 125.4) -- also runs on 19v like SAX-125.4 SAX-100.4 v.2 ($400 MAP) : Four channel Class-A/B design with similar crossovers to the 125.4 -- but a lower price as it's an A/B amp. Now featuring a fan as with most of our new stuff. This model will run to 16.5 volts. SAZ-5000D ($1520 MAP) : All new case tool about 3" narrower than the 4500D/NS-1 casing; similar design to the 4500D but beefed up to carry a 5000 rating from us. NS-1 v.2 ($1900 MAP) : Same new case as 5000D; will be about 3" narrower / 3" longer than current model with pretty well identical internal components and same price. Many customers were looking to go narrower so we've been working on this for a bit. ---------- Some of the SAE amps will also be launching -- MAP will be close to what I discussed originally. I posted about the "E" line prototypes some time ago; I was very happy with them. Now a few are coming out this year. Case tool will look similar to the newer case SAZ line. These come with remotes / are stable to 16.0 volts (not 16v system stable). There are some changes compared to prototypes and I will get more information up before any pre-ordering goes up. ---------- SAE-600D ($209 MAP) : The board is like the "500D" I posted about a while back that well exceeded the power expectations. http://www.caraudioclassifieds.org/forum/sundown-audio/89173-ns-1-sae-500d-prototype-pictures.html SAE-1000D ($269 MAP) : Little smaller version of the 1200D board posted about earlier. http://www.caraudioclassifieds.org/forum/sundown-audio/107782-sae-800d-1200d-50-4-prototypes.html SAE-50.4 ($159 MAP) : More basic crossover function from our other gear -- Class-A/B design. Pretty much like the prototype but with our tooled case. http://www.caraudioclassifieds.org/forum/sundown-audio/107782-sae-800d-1200d-50-4-prototypes.html ---------- I will start releasing more information as we get closer to pre-orders. Info that isn't here already and pictures will be coming along!

As we get everything ironed out and fully tested we'll be able to make a time-line ; as of now I don't have a date.