cloud77

I might be down at a show in Columbus/Mansfield this season, so maybe you can =]

I hope so. but I'm not really worried about numbers. Just some clean old fashioned XXX sound

not walling as if right now, as I may get a new vehicle.

You can fit a 15" but its a snug fit

Well, here are the components to the dream build. Just finished the last one up last night. (2) RE XXX 12" OEM coil 1 stiff, 1 soft spiders Original full face dust caps Amps MMATS HD4000.1 MMATS SQ4100 Speakers: (2) Sets of Infinity Kappa 6.5 components Electrical: Singer 250A 3 runs 2/0 Duralast platinum(front) (still needing rear batteries) Vehicle: '04 Pontiac Grand prix Enclosure talk: I have experience with this driver in different sizes, and had always had good results with the enclosures for them. Haven't done a multiple woofer set-up for almost a decade, but this is what I was thinking.. 4.5 cu. ft. L port, double baffle, window bracing, 45s Going to start with subs back port back, and if I want to I will flip the box around and seal a trunk wall. Anyone with experience with these drivers want to chime in? I'm thinking with the power I had I would want to keep air space around 2 cubes each. Would also contemplate center port, but would change up bracing a bit. Gotta wait for the weather to break to get this built! Now for the photo shoot...

OEM coil, but suspension is different. 1 hard, 1 soft spider

I'm doing (2) 12" build with (2) XXX in the trunk of my Grand Prix. I have 4k..Should I go closer to 2 cubes each?

lol

Almost thought about an IB build for my trunk with 12"s

Awesome man. Really would like to use my XXXs in an IB application some day.

I'm loving it. I have two drivers that I plan on keeping after the days of car audio for this type of application.

been seeing a lot of deer now that I'm not thumpin'

=P

you should be able to fit a group 34

yes, understood. I went with OEM coil and suspension. Just ordered my first recone, on top of a frame, enough glue, and the dish dustcaps with original XXX logos Dave had laying around =] Still need a battery and another run of 1/0. Going to start planning the trunk wall..can't wait until I get my tax refund.

I will use a dual stiff spider on these and be over powering them a bit.

Thinking of building a box outside of trunk and sealing it to the frame leading to the back seats. Can't be more than 34" wide and 14 tall to accommodate fitting it in from back. I hope I have enough width to give it port. And I would probably tune @ 30 with 75-80 sq inches of port. In no way am I trying to be efficient, put up numbers, exc.

Thanks for the input. You trying to get your post count up by posting that? and yes I am.

F that I'll build. seal off. listen. repeat.

Sorry op, but I couldn't help but laugh at the title of this post.

Might wait to run both. Not sure if my car will be able to handle the weight.

lol ^ trying to get post count up?

really want to load them off the trunk though. ugh

Got another addition to the family today. I have all winter to build these...so its time to ponder enclosure ideas. Building into 12"s. Going in the trunk of a 04' Grand Prix Thinking of allocating about 5 cubes to L port. Box can be deep as long as its not over 15 " tall. Was also thinking if a 4th order would be worth it, but its very hard to find info on successful sealed builds with these, So I'm taking a shot in the dark. Sub forward port forward may not fit across very well. It will be tight. But probably would work. They are very heavy drivers however, and would like to have space for bracing. Was maybe thinking aero port to driver side, or..