shizzzon

Here is a picture of it in use approximately 8 minutes after applying it. I will have another pic or video later on today when it's cured and final view of it tomorrow when it's completely cured.

Holy Shit! It was talking air out of your lungs? I have never yet heard of the ancient language of AIR but i heard it was a breeze once you get the hang of it.

I didn't know he had already proposed! Oh and happy Birthday, Mark.

Maybe Krypto needs me to design him a box... uh oh...

this design is bare tuned to 36hz and plugged to 30hz. As mentioned above about no port kerfing, if you have enough solid port area, flaring a port can\will actually decrease spl potential output. That's why you do not see walls always kerfed or flared like crazy! Yes he does still have potential but we can say now that this box is very efficient!

it's 1ohm STEREO, 2ohm MONO stable.(the ap30001d)

if it goes in protect at 4 ohms then u have a problem... the amp is 2 ohm stable in mono.

a picture would be awesome of this metal piece

he is working on the cutsom fuse holders.. The 300A fuse popped on the stetsom 5k and he's workin on installin dual anls to hopefully fix the issue. He just sent me a pic of what he just hit on the meter but i do not know where it was metered at, i'll let him tell us. Also, he is going to brace the rear wall where the port is because he said it's flexing and that wall can only be braced externally so let's see what he does.

don't make all of us drive to california and diagose the problem with all this cheap gas prices goin on right now..

Here is pics of the resin container. Hardener container says same thing...

leave it on then, do not turn it off

it's apparent it's not out of phase. do this- BUT DO NOT LEAVE IT LIKE THIS!- Turn gain clockwise all the way. Turn LOW PASS FILTER clockwise all the way Turn SUBSONIC FILTER counter-clockwise all the way UNPLUG ANY remote knob coming from the amp. Tell us what happens. You run a risk of destroying the sub by leaving your amp like this if and only if it really starts to get loud. What i need to know is if it gets considerably louder, like a LOT louder... IF it is, it's your settings or the remote knob on the amp set wrong.

Just playin.. hehe.. Was your heart racin there for a minute?

OH Noes! I forgot to tell u something.. u gonna screw the whole box design up!

ok... where was the meter?

maybe i am looking at this wrong

NO... u are doing it WRONG... Parenthesis inside AND anything strictly attached to it is done FIRST. 9+3 = 12 2(12) (This STILL needs to be simplified before solving... So = 24.. Now we have 48 / 24 = 2

you are wrong because Parenthesis comes before all that... Seriously like Duran and kirill said.. We should be lucky that these equations are not used in car audio, lol.

wow i havent heard that in forever... But yes, 2 is the answer. Apparently, the other TI calculator wasn't given proper instructions in it's firmware to know basic rules. Sad though.. that one is newer

i seriously think u shouldnt be using an EQ to try and bring out ANY frequency.. especially at 9db if i read that right... if the install isn't loud at certain notes, it's either tuning error, wrong box size, firing direction or just shitty equipment... Forcing a boost at any frequency is going to cause a situation where other notes won't be as loud.. it's practically common sense. So, quit confusing yourself and let your install do the sound for you, dont be god over there without the god knowledge... Can't change output on everything just by changing settings... Greatest effect on changing output is install dependent. that EQ is going to cause you more problems and heating up coils and isn't worth it.

you email this address- [email protected] And malibuon22s... I already beat ur idea, hehe. I'm runnin 4 of em all strapped @1ohm.. but not the 3.5s.. no no no... the 5.5s

soon.. I've already preordered mine. Preorder ends next friday.

how about this- Invert the subs. that way, practically any sub will look great.

honestly at this point.. if it's metal to metal anymore, i'm just gonna mig weld it. And yea tirefryr, i know this glue is epoxy resin based but i was under the assumption that the fillers they are using with the resin has something to do with changing some of it's properties... Either way, like dutchie wants, i'll post up what happens by the end of next weekend after it cures.